Philips 20TA1000/98 Cable BOX with RF in / Outputs, Cable BOX with Audio / Video Outputs

Page 6

CABLE BOX (WITH RF IN / OUTPUTS):

1

2

3

Connect the Cable TV signal to the IN jack (or RF IN or CABLE IN) on the Cable Box.

Connect an RF coaxial cable (not supplied) to the OUT jack (or TO TV or RF OUT) of the Cable Box.

Connect the other end of the coaxial cable to one end of the supplied L-Adapter as shown, and connect the other end of the adapter to the TV jack on the LCD TV.

The Cable TV signal from

 

 

 

the Cable Company

 

 

 

 

 

 

 

OUTPUT

 

 

 

CH

CABLE

TO TV

3

4

 

 

IN

4

Plug the DC adapter into the DC IN 16V jack on the LCD TV.

 

Plug the power cable into an outlet and switch TV set on.

 

5

Set the Channel 3/4 (or Output channel) switch of the Cable Box

 

 

to 3 or 4. Set the TV to the same channel. When watching TV

 

 

 

programming, change channels at the Cable Box, not the LCD TV.

 

 

 

HELPFUL HINT

 

 

 

Immediately after unpacking and plugging in your new television,

VGA

 

PC

 

 

 

run the auto program function to set up the TV for the broadcast

 

 

or cable channels available in your area. If you do not run the auto

 

program function to set up the channels , your television may not

operate properly.

DC Adapter

 

Please make sure that you have selected the TV mode with AV key

 

on your remote control, before installing TV channels.

 

 

Power

 

Cable

75

Coaxial

Cable

CABLE BOX (WITH AUDIO / VIDEO OUTPUTS):

This connection will supply stereo sound to the LCD TV.

1

Connect the Cable TV signal to the IN jack (or RF IN or CABLE

 

 

S - VIDEO

IN) on the Cable Box.

 

 

 

 

 

 

 

AUDIO

 

Using an RCA-type video cable (not supplied) connect one end of

 

 

VIDEO

2 the video cable to the Video Out jack of the Cable Box. Connect

 

 

 

 

 

 

the other end of the cable to the yellow VIDEO jack on the side

 

 

 

 

of the TV. Video cables are usually marked with yellow and are

 

 

 

available from Philips or electronics retailers. Video jacks on most

 

 

 

equipment are yellow.

 

 

 

Using RCA-type, stereo audio cables (not supplied), connect one

 

VGA

 

3 end of the cables to the left and right Audio Out jacks of the Cable

Video Cable

PC

 

 

Box. Connect the other end of that cable to the Audio jack on the

 

 

 

 

 

side of the LCD TV. Audio cables are usually marked with red and

 

 

 

 

white and are available from Philips or electronics retailers. The

 

DC Adapter

 

 

right audio jack is red and the left audio jack is white. Match the

 

 

Audio Cable

 

cable colors to the jack colors.

 

 

 

4

Note:

Plug the DC adapter into the DC IN 16V jack on the LCD TV. Plug the power cable into an outlet and switch TV set on.

Use the AV button on the remote control to tune to the AV channel for the cable box signal. Once tuned, change channels at the cable box, not the television.

When you watch programs using VCR, it’s recommended to select SOFT Mode via Smart picture.

Power

 

 

 

 

 

 

Cable

Cable

 

 

 

 

 

 

 

 

 

 

 

 

TV signal

 

 

 

 

 

 

 

OUTPUT

 

 

 

 

 

CH

 

 

CABLE

TO

3

4

L AUDIO R

VIDEO

 

IN

TV

 

 

OUT

OUT

Cable Box

6

Image 6
Contents Contents Installing LCD TV on the WallUnfold the Base TV Channel Installation Presentation of the LCD TVAccessories Battery InstallationRemote Control Operation Antenna TV Basic Cable TV ConnectionHelpful H INT Auto Program Setting UP Channels Manual Store of TV ChannelCable BOX with RF in / Outputs Cable BOX with Audio / Video OutputsHelpful Hint Video Connections HD ConnectionsPC Monitor Inputs