Philips 60PP9502, 55PP9502 manual Setting the TIMER’S Start Time and Stop Time

Page 43

Using the Onscreen Submenus: Features

SETTING THE TIMER’S START TIME AND STOP TIME

You can set the Timer to switch to a selected channel at a specific time while you are watching another channel, or when the TV is in standby mode. (Standby mode is when the TV is

plugged into the wall outlet but turned off.) If you want, you can also set the TV to turn off at some time after the TV switches channels. Follow the steps below to set the Timer’s START TIME and STOP TIME.

BEGIN

1 Press the MENU/SELECT button on the remote control to show the onscreen menu.

2 Press the CURSOR RING DOWN

twice to highlight FEATURES.

3 Press the CURSOR RING RIGHT to enter the FEATURES submenu.

4 Press the CURSOR RING RIGHT again. Then press the CURSOR RING DOWN once to highlight the START TIME control.

5 Press the CURSOR RING RIGHT to highlight the time indicator area.

6 Press the NUMBER buttons to enter the correct time. If you make a mis- take entering the time, use the CUR- SOR RING LEFT or RIGHT to move among the time input slots to make corrections.

NOTE: You can also use the CUR- SOR RING UP or DOWN to cycle through digits to input the time.

7 Press the CURSOR RING UP or DOWN to select AM or PM.

8 Press the CURSOR RING LEFT repeatedly until START TIME is high- lighted. Then press the CURSOR RING DOWN to highlight STOP TIME. If you want the TV to switch off at some time after the changing of channels, follow steps 5–7 above to set the STOP TIME.

9 Press the STATUS/EXIT button to exit the menu.

See pages 44 and 45 for instructions on selecting the Timer’s channel and activating the timer.

PICTURE	TIMER
SOUND	AutoLock
FEATURES	PIP
INSTALL	CLOSED CAP
	FORMAT

			POWER
	7	VCR	ACTIVE ACC	3,4,
	7	PIP CH	CONTROL FREEZE	5
9		UP
9	SOUND
	STATUS/		MENU/
	EXIT		SELECT
	8	MUTE	2	1
			2	1
	1	2	3
	4	5	6
	7	8	9
6	TV/VCR	0
	A/CH	0	SURF
		POSITION	PIP

FEATURES
		TIME
	TIMER	TIME
	AutoLock	START TIME
	PIP	STOP TIME
	CLOSED CAP	CHANNEL
	FORMAT	ACTIVATE

FEATURES
TIMER
TIME	8:06 PM

START TIME

STOP TIME

CHANNEL

ACTIVATE

FEATURES

TIMER

TIME

START TIME

_ _:_ _

STOP TIME

CHANNEL

ACTIVATE

FEATURES
TIMER
TIME
START TIME	8:00 AM
STOP TIME
CHANNEL
ACTIVATE

FEATURES
TIMER
	TIME
	START TIME
	STOP TIME	_ _:_ _
	CHANNEL
	ACTIVATE
FEATURES
TIMER
	TIME
	START TIME
	STOP TIME		9:30 AM
	CHANNEL
	ACTIVATE

43

Image 43

Contents Hdtv Monitor Warranty Verification Important Safety Instructions Contents High-definition component and digital visual interface DVI FeaturesWhatYou Can Connect to Standard Panel Jacks Panel Overview Standard Inputs and OutputsWhatYou Can Connect to High-definition Input Jacks Panel Overview HIGH-DEFINITION InputsRear of TV Connecting a VCRANT Connecting a VCR and Cable BOXSee the section below on using the Audio OUT control Connecting and Using AN Audio HI-FI System with Your TVMaking Optional SURROUND-SOUND Connections Rear of DVD Player Connecting a Standard DVD PlayerCH3CH4 Connecting AN S-VIDEO DeviceAV4 Connecting a DVD Player with PROGRESSIVE-SCAN CapabilityConnect S-VIDEO and audio cables. Note This example uses Connecting AN HD Receiver to the HD INPUT-AV 4 JacksConnect coaxial cables AV3 Connecting a CamcorderConnecting and Using Headphones with Your TV VCR Programming the TV Remote to Work with Accessory DevicesPlease read through all the steps before beginning Using the CODE-ENTRY Method to Program Your TV RemoteUsing the Search Method to Program Your TV Remote VCR DIRECT-ENTRY Codes for A/V Accessory DevicesTelevision CH & TV/VCR Using the TV Remote with Accessory DevicesSource you want to watch Using the AV and Source Select ButtonsAutoSound Options Using AutosoundColor Picture Using AutopictureSurf List Empty Using AutosurfProgram List CVI Using Program List and Alternate ChannelSleep Timer Control UsingPicture-adjustment Options Adjusting the Picture ControlsPress the STATUS/EXIT button to turn the menu off Setting the EYE Fidelity ControlPicture Sharpness Tint Setting the Dynamic Contrast ControlConverge RED Adjusting the Manual Converge Controls Converge RED/BLUESwap Adjusting the Manual Converge Controls Multipoint RED/BLUEAdjusting the TREBLE, BASS, and Balance Controls Using the AVL Audio Volume Leveler Control Selecting the SURROUND-SOUND Modes Selecting a Surround-sound Option Using Remote ControlSelecting the STEREO/MONO Sound Mode Selecting SAP Using Remote Control Selecting the SAP Second Audio Program FeatureSelecting SAP Using TV Buttons Speakers Using the Bass Boost ControlFeatures Setting the ClockDisplaying the Time Time Setting the TIMER’S Start Time and Stop TimePress the Cursor Ring Right to enter the Features submenu Selecting the TIMER’S ChannelSetting the TIMER’S Activate Control TV TV-Y7 Directed to Older Understanding AutolockTerms PG-13 Parents StronglyFeatures Setting UP the Autolock Access CodePIP Install Closed CAP Using Autolock to Block ChannelsPress the MENU/SELECT Using Autolock to Block by Movie RatingUsing Autolock to Block by TV Rating Control does not affect channel blocks see Turning the Autolock Blocking Control on or OFFUsing Autolock to Block Unrated Broadcasts Using Autolock to Block Broadcasts That have no Rating Press the STATUS/EXIT button on Reviewing Your Current Autolock SettingsMute Using the Closed Captioning ControlSelecting a Picture Format Using the Remote Control Using the PICTURE-FORMAT ControlSelecting a picture Format Using the TV Buttons Turning Active Control on or Off Using the TV Buttons Using Active ControlHD INPUT-AV Model SpecificationsSpace for HD INPUT-AV Setting ColorVideo-game images and scoreboards Care and CleaningTV has no power TroubleshootingYou are not able to get sound Glossary of Television Terms Index Washington/Baltimore call Philadelphia Factory Service LocationsHouston Page Page Page Projection Television Limited Warranty