Philips FTR 9965/12 manual Tips, Displayed time is wrong

Page 25

Tips

 

Poor Picture

Have you selected the correct TV system in the manual installation menu?

 

 

• Is your monitor or house aerial located too close to loudspeakers, non-earthed

 

 

 

audio equipment or neon lights, etc.?

 

 

Mountains or high buildings can cause double pictures or ghost images.

 

 

 

Sometimes you can improve the picture quality by changing the direction of the

 

 

 

aerial.

 

 

Is the picture or teletext unrecognisable? Check if you have entered the correct

 

 

 

frequency. See Installation, Manual installation, p. 6.

 

 

• Are brightness, sharpness and contrast out of adjustment? Select Factory

 

 

 

settings in the Setup, General menu, p. 8.

 

 

 

 

 

No Picture

Are the supplied cables connected properly ? (The aerial cable to the receiver

 

 

 

box, the other aerial to your recorder, the VGA cables to the display, the power

 

 

 

cables.)

 

 

Has the child lock been switched off ?

 

 

Is your PC switched on ?

 

 

Do you see a black screen and the indicator in front of the monitor lights up

 

 

 

green, this means that the display mode is not supported. Switch your

 

 

 

VGA-source to a correct mode.

 

 

• In case of weak or bad signal, consult your dealer.

 

 

 

 

Digital distortion

The low quality of some digital picture material may be the cause of digital image

 

 

distortion. In this case select the Soft setting using the Picture menu, Smart Picture,

 

 

without changing the picture settings manually.

 

 

 

 

 

No sound

No sound on any channel? Check the volume isn’t at minimum.

 

 

Is the sound interrupted with the mute key ¬?

 

 

 

 

 

No Surround

Check if the headphone is not plugged in.

 

sound

Perhaps the channel is not broadcasting good quality surround sound.

 

 

No sound from the rear speakers or the centre speakers? Select an appropriate

 

 

 

surround mode, according to the broadcasted sound signal or adjust the

 

 

 

volume. See Surround Modes, p. 12.

 

 

 

 

No solution found

Switch your TV off and then on again once. Never attempt to repair a defective

 

for your picture or

TV yourself. Check with your dealer or call a TV technician.

 

sound problem ?

 

 

 

 

 

 

Menu

Have you selected the wrong menu? Press the MENU key again to exit from the

 

 

menu.

 

 

 

 

NEXTVIEW

Orange indicator on front of the TV during standby / No NEXTVIEW info:

 

 

See Acquisition and updating of NEXTVIEW information, p. 16.

 

 

Displayed time is wrong:

 

 

The broadcaster on programme number one does not transmit the correct local

 

 

date and time. Use Reshuffle in the installation menu to place another broadcaster

 

 

on programme number one.

 

 

 

 

Remote control

• Check if the remote control is in the correct mode.

 

 

• If your TV no longer responds to the remote control, the batteries may be dead.

 

 

• You can still use the MENU key and the -/+ keys in front of the receiver

 

 

 

 

23

Image 25 Contents
Flatl TV Cable Contents Preparation Use of the remote control RC4301 Active control see p Picture format Keys in front of the TV receiver boxMenu key to confirm your selection Installation menu contains the following items InstallationTo use the menus Select the menu language and countryManual installation Automatic installationStore TV channels Select your choice with the cursor rightReshuffle the programme list Give nameSelect Favourite TV channels You can change the order of the stored TVGeneral TV SetupSource TV menu DecoderPicture menu Active Control Sound menu Features menuOn timer SleeptimerSelect subtitles Child lockDisplay options Dual screen / PIP / MultipipScan PIP 3, PIP 8 or PIP Define the position of the single PIP screenCall Nextview / Teletext guide Nextview / Teletext guidePicture/NEXTVIEW Teletext Guide Nextview guidesBasic functions Teletext GuideAcquisition and updating of Nextview information Teletext Switch Teletext on and offSelect a Teletext Previously selected teletextTeletext menu Connect Peripheral Equipment With Component Video Output Connectors ExternalRecorder VCR-DVD+RW DVD playerMulti channel Surround receiver Side connectionsCamera or Camcorder HeadphoneRecorder or DVD with EasyLink VGA menuSelect one of the menus with the cursor left/right Audio- and video equipment keys To switch to standby For pause VCR, DVD, CD For recordSelecting submodes for DVD+RW, SAT, CDR Record with your recorder with EasyLinkDisplayed time is wrong TipsPower consumption around 300 W Ambient temperature + 5~ + 40CWeight excl. packaging 4 kg Dimensions wxhxd Receiver 43.5 x 10.5 x 33 cmPage RecorderDVD English Receiver menu Activating CinemaLinkSmart Sound,Treble, Bass LoudnessSpeakers menu Surround menuManual installation Automatic installationGive name Reshuffle See the Instructions for Use of the TV or receiver boxFlatl TV VGA Unpacking and wall mounting instructions Operation Monitor Display modesUse of the remote control Use of the menus and the menu system Colour temperaturePicture 1 menu Picture 2 menuSound menu Setup menuPlasma Display characteristics Ambient temperatureCare of the screen Control of peripheral equipmentPage 3122 126
Related manuals
Manual 44 pages 25.05 Kb Manual 42 pages 14.22 Kb