Philips 44PL9523, 55PL9223, 55PL9523 setup guide Groove

Page 72
Align the groove on top of the new lamp’s housing with the corresponding groove pocket inside the TV, then slide the new lamp into place.
7 Tighten the thumb screws clockwise until finger tight only. Do not over- tighten.
8 Slide the lamp door closed. IMPORTANT: The door must be closed completely to the left. Otherwise, the TV will not operate.
9 Go to page 73 for instructions for set- ting the Lamp Rating and resetting the Lamp Lifetime Counter.
CAUTION: When installing the new lamp, do not touch the glass envelope. Oil from skin can reduce lamp life.
6
CAUTION: When removing the lamp, do not touch the glass envelope. It may still be hot.
Grasp the handle, then pull out and slightly down to remove.
WARNING: The lamp contains mer- cury. Dispose of the lamp in accor- dance with local, state, and federal regulations.
5
Continued from page 71.

Replacing the Lamp

5

6

Groove

7

8

INT

EXT

9

Go to page 73 for instructions for resetting the Lamp Lifetime counter through the TV’s on- screen menu.

72

Image 72
Contents Hdtv Monitor Liquid-crystal-on-silicon Lcos High-definition ImagingProduct Ownership Dear Philips product ownerImportant Safety Instructions Contents Features Information about TV Signals Resolution informationYour High-definition-ready Set Interlaced ScanDescriptions of Jacks, Cables, and Connectors AV 1 Input Jacks Signals accepted Ntsc Panel Jack Compatibility InformationPre-connection Recommendations Positioning the TVConnecting a VCR Color Coding Used on Jacks and Plugs to simplify connectionsConnecting a VCR and Cable Box Back of TVConnecting an S-Video Device Back of TVConnecting a Standard DVD Player Helpful HintsConnecting a Progressive-scan DVD Player Back of TVConnecting an HD Satellite Receiver to YPbPr Connecting an HD Satellite Receiver to DVI ListedConnecting Surround Sound Equipment Front SpeakersConnecting to the Side Inputs Video Game System Labeling the Audio/Video Input Sources Mode TV, CBL,VCR,AMP, HD, SAT, DVD, or CD Volume VOLSource Select Picture FormatPower-Standby VCR Prog functional only in VCR modeAlternate Audio Surround SoundProgramming the TV Remote to Operate Accessory Devices Using the Code Entry Method0809 Setup Codes for Accessory Devices VCR VCR Mode VCR TimerPower VCR ProgUsing Active Control Plus Active Control Plus+ SettingsUsing the Zoom Control Adjusting/Setting the Picture Controls Picture Control SettingsSelecting a Digital Processing Option Selecting a Dynamic Contrast Option Press the Cursor Right button to select PictureSelecting a DNR Dynamic Noise Reduction Option DNR is not available for use with input sources AV3-AV6Turning on Color Enhancement Selecting an AutoPicture Option AutoPicture OptionsSelecting a Picture Format Option Your TV’s Picture Format OptionsPicture Automatic Adjusting the TV and Headphone Volume To control the television volumeTo control the Headphone volume Selecting a TV Equalizer Option Adjusting TV Speaker Balance Turning Loudness on or off Selecting a Sound Mode Option Using Alternate Audio SAP Setting the TV for Stereo Programming Turning the AVL Audio Volume Leveler on or off Adjusting the Delta Volume Selecting an AutoSound Option AutoSound OptionsUsing Closed Captioning CC-1, CC-2, CC-3, or CC-4-DialogueSetting the Sleeptimer Setting the On Timer Using the Channel List Removing Channels from the Channel List Using Lock Channel Using Lock After CancelBlocking Programming Based on TV Ratings TV Ratings from TV BroadcastersBlocking Programming Based on Movie Ratings Movie RatingsTurning the Antenna Attenuator on or off Using Surf Using Dual Screen and PIP When using Dual Screen When using Large or Small PIPWhen using PIP3 or PIP6 To reposition the PIP screenSelecting a Picture Freeze Option Freeze Replay Photo finishResetting the Audio/Video Settings to Factory Default Values Minimum mode default mode Selecting an On-screen Display OptionSetting up or Changing a PIN Personal Identification Number Setting the Subwoofer Control Setting the Clock-Auto Clock Mode Auto Clock ChannelSetting the Clock Manually General Source Using Installation Features Language and Autoprogram For LanguageFor AutoProgram Cleaning the Cabinet Cleaning the ScreenCleaning or Replacing the Filters Replacing the Lamp Groove Resetting the Lamp’s Lifetime Counter You have changed the lampTroubleshooting Remote-related Checks Remote control does not work TV-related Checks You have no pictureYou have no picture and no sound You see scrolling imagesProduct Specifications PictureIndex Picture ControlsThis page intentionally left blank This page intentionally left blank Philips Limited Warranty