Philips VR 260/07 Adapting remote control, Recorder. Each button has been allocated a specific

Page 44

MAIN MENU

CLOCK

AUTO INSTALL

MANUAL SEARCH

TV CHANNEL ALLOC.

RECORD SPEED

AUTO STANDBY

TV SYSTEM

SPECIAL SETTINGS

EXITPMENUOK

Adapting remote control

If you are using two video recorders which both react to the same remote control codes, you can use this function to change remote control and video recorder to other codes.

What are remote control codes?
Each time the button on your remote control is
pressed, an invisible infra-red signal is sent to the video
recorder. Each button has been allocated a specific
code, which ensures, that the video recorder will carry
out the corresponding function. If two video recorders
respond to the same codes, the remote control signal
emitted will be recognised and performed by both.
Therefore the possibility exists, to allocate different
remote control commands (with other codes) to this
video recorder. This means that the uninterrupted use	PARDON?
of both video recorders is possible once more.	PARDON?

1Press the MENU button on the remote control.The on-screen menu appears

2On the remote control press the buttons SELECT and 2 simultaneously, to set the video recorder to “VCR 2” (or SELECT and 1, to set it to “VCR 1”)

What must I set?
If two video recorders respond to the same codes,
they are either both set to “VCR 1” or “VCR 2”. Please
change the setting of only one video recorder! The	TIP
factory setting of the video recorder is “VCR 1”.	TIP

3Confirm with OK. The screen will show “RESPONDS TO VCR 2” or “RESPONDS TO VCR 1”. The on-screen menu disappears The adjustment of the remote control is complete

8My on-screen menu does not disappear

4The video recorder does not recognise the change of remote control codes. Repeat steps 2 and 3

8After the buttons are pressed “VCR 1” or “VCR 2” appears in the display of the video recorder

4Repeat step 2to reset the remote control to the displayed settings

PROBLEM

ADAPTING REMOTE CONTROL	44	ENGLISH

Image 44

Contents Table of contents VR 260/07 WithRemote control Introduction Important notes for operationMost important functions of your new video recorder Important information for customers in Great Britain Connecting the video recorder Preparing the remote control for operationConnecting to a TV set with a scart socket When using this video recorderProblem Confirm with OKCheck the cable connections Connecting additional devicesThere is no test image Initial installation Setting TV channels, date and time for the first timeWhat is an on-screen menu? What is a channel, or a special channel?Searching for a TV channel manually Following the corresponding instructions on Screen.PARDON?What is a decoder? Allocating decoderDon’t know the channels for my TV stations Desired TV stationUsing a satellite receiver Check decoder allocation at a glanceTo which TV channel on the video recorder a decoder is This channelSettings Searching for TV channels automaticallySorting and clearing of TV channels manually Changing the time and date Additional 0.Therefore for 9 you must enterNavigation in the main menu Operating instructionsGeneral information Playing back Ntsc cassettes PlaybackPlaying cassettes Selecting tape position display type What types of display are available to me?Display shows the playing time Remaining until the end Cassette 0000 hours / minutesReset / display tape position Button GBookmark at the appropriate place on the tape Later by pressing a buttonStill picture / slow motion Immediately to playback Play compact VHS cassettesOptimizing still picture Removing picture interferenceOptimizing tracking Manual recording Starting recording manually Stopping automatically Lining up manual recordings Selecting the recording speedStandard Play / Long Play / Auto Long Play Duration of the programmed recording,Recording automatically from a satellite receiver Is practically no loss of quality during transfer. WeIs switched off Activate / deactivate direct recordingCannot select on or OFF That direct recordings are not possibleMaking a direct recording Programming timer with Video Plus+ Programmed recordingsSignals on * or off Explains how to set the desired recording speedActivate VPS/PDC Even if they are rescheduled. In the input fieldProblem solving Video Plus-Programming ProblemsolutionProgramming timer without Video Plus+ What is a memory location?Store up to six timer programmings Friday or WEEK. for recordings which areProgramming Timer Without Video Plus English Problem solving Timer programming And/or v are flashing in the display of the video recorderTurbo Timer-Recording Problem solving Turbo Timer programming It has been manually deleted Using the NexTView LinkDelete / check / change programmed recordings 10Other functions Adjusting automatic switch-offAdjusting the child lock Replaying cassette continuously Repeat PlayChanging the TV system TV systemsProcess and show several transmission systems Select AutoAdjusting the OSD information What is an OSD?On-screen menu by following the corresponding Instructions on the screenEnergy-saving mode Adapting remote control Factory setting of the video recorder is VCRRecorder. Each button has been allocated a specific Both video recorders is possible once moreUsing the TV remote control Remote Control CodesThese signals are transmitted Display.PROBLEM11Suppressing interference Optimizing the modulatorSwitching the modulator on / off Switching off the modulatorWith a scart cable, you can switch off the modulator When there is interference with the picture or soundPossible Cause / Solution 12Before you call an engineerEnglish English Video recorder / display English