Rerecording (Tape Duplication) 31
AUDIO and VIDEO OUT Jacks on source unit | CC13C1MG |
(VCR or Camcorder) | |
AUDIO VIDEO | STOP R |
EARPHONE | EJECT |
|
VIDEO AUDIO 
OUT
IN
Audio Cable from |
AUDIO OUT to AUDIO In |
Video Cable from | AUDIO and VIDEO In |
VIDEO OUT to VIDEO In | Jacks on TV/VCR |
1
Make the connections shown above, using audio and video cables (not supplied). Connect the source unit (VCR or camcorder) to a power source after connections are made.
2
The source unit will play your tape. Insert a prerecorded tape in the source unit. If playback begins, press the STOP button on the unit.
3
The TV/VCR will record your tape. Insert a blank tape in the TV/VCR. Make sure the tape’s record tab is intact. The TV/VCR power will turn on automatically.
4
Point the TV/VCR remote control at the TV/VCR. Press
Number buttons 0, 0 so that A/V IN appears on the screen.
The TV/VCR is now in Line Input mode.
5
Point the TV/VCR remote control at the TV/VCR. Press the SPEED button until the desired tape speed (SP or SLP) appears on the screen.
6
Press the PLAY button on the source unit and the REC(ord)/OTR button on your TV/VCR at the same time. Copying will begin.
7
To stop copying, press the STOP/EJECT button on the TV/VCR, then stop the tape on the source unit (VCR or camcorder).
Helpful Hints
•Unauthorized recording of copyright- ed television programs, video tapes, or other materials may infringe on the rights of copyright owners and violate copyright laws.
•Different brands of equipment may operate differently.
•Make sure all connections are secure. Otherwise, you may not record both picture and sound.
•Programs that are copyright protected may not record clearly.
Tvcr
For Customer Use
Warranty Verification
Declaration of Conformity
Features
Safety Precautions
Introduction
Table of Contents
Replace the battery compartment lid
Battery Safety
Using the Remote Control
TV/VCR Maintenance
Rod Antenna
Hook up your TV/VCR using one of the connections shown
Hooking Up the TV/VCR
RF coaxial cable Not supplied
Cable Plug
Hooking Up the TV/VCR cont’d
Bent pin
Crooked Pin Straight Pin
Press the Menu button. The screen shown below will appear
Turning On the TV/VCR
Press the Menu button
Language Selection
Select Language English Español Select KL To END Press Exit
Wait for the TV/VCR to set up channels
Automatic Channel Setup
Programming of the channel you added or deleted will appear
Adding/Deleting Channels
Press the PLAY/o button or the STOP/p button to select
Repeat steps 3-4 to add or delete other channels
Manual Clock Setting
Setting the Clock
Cable Box users must set the clock manually
Date Sunday To Correct Press Clear To END Press Exit
SET Manual Clock Time Date To END Press Exit
SET Manual Clock Time
Month To Correct Press Clear To END Press Exit
Automatic PBS Channel Selection
Setting the Clock cont’d
PRIM. Setup Press B
VCR Program VCR Setup Caption Reminder Brightness
SET Auto Clock Time
NOW Searching flashes on the TV/VCR screen
Wait for the TV/VCR to find the time
SET Auto Clock Time Date NOW Searching To END Press Exit
Manual PBS Channel Selection
Use the Number buttons to select your PBS station
Press the PLAY/ button or the STOP/ button to select
PRIM. SETUP. Then, press the F.FWD/B button
PRIM. Setup Press B VCR Program VCR Setup
Daylight-Savings Time
Press the Menu button, then press the STATUS/EXIT button
Primary Setup
Volume BAR SET Clock Select KL Choose B To END Press Exit
Time Zone
Front Panel
Connect your antenna or cable here. Details are on page six
AC Power Cord
Rear Panel
ANTenna Jack
Remote Control Buttons
STOP/ Button
Menu Button
STATUS/EXIT Button
REWind/ Button
When you finish, press the STATUS/EXIT button
Adjusting the Picture Controls
Decreased brightness
Adjusting the Picture Controls cont’d
Tint KK Sharpness TV Reset
Decrease Increase
If you select Status OFF
On-Screen Status Displays
If you select Status ON, then select Counter only OFF
If you select Status ON, then select Counter only on
OFF
Reminder
Follow the steps below to play a tape
Playing
Insert a tape in the TV/VCR
Hrs
Recording
Read and follow the steps below to record a TV program
To stop recording, press the STOP/ button Tape Speeds
Press the STOP/EJECT but- ton on the TV/VCR to stop the OTR
Length Press OTR Cancel Press Clear
One-Touch Recording
Tape is in the TV/VCR. The record tab must be intact
Rerecording Tape Duplication
TV/VCR is now in Line Input mode
Daily
Timer Recording
Select Program Number To END Press Exit
Time OFF To Correct Press Clear To END Press Exit
ONE Time Program Channel Time on
Timer Recording cont’d
Gram Review and press the F.FWD/B button
Timer recording information for the program in the lowest
With the TV/VCR on, press the Menu button
Program REVIEW, then press the F.FWD/B button
REC Defeated
VCR Setup ONE Time Play
Defeat Recording
Follow the steps below to prevent accidental recording
TV programming will appear while the tape is rewinding
VCR SETUP, then press the F.FWD/B button
VCR Setup ONE Time Play Repeat Play on
Repeat Play
B Repeat Play
VCR Setup ONE Time Play Repeat Play A-B
Insert a tape in the TV/VCR Press the Menu button
Repeat
Repeat Play cont’d
Appear on the screen
Real-Time Counter Memory
Stop
Super High Speed Searching LP/SLP
Forward and Reverse Searching SP/LP/SLP
Viewing a Still Picture
To block ratings, follow the steps below
SmartLock
Smartlock menu will appear
Ratings are defined on
SmartLock cont’d
Example Specific Sub-ratings
After you enter the code, the Smartlock menu will appear
To change the access code, follow these steps
TV-Y7 TV-G
Blocked Ratings
Blue Background
VCR Program VCR Setup Caption Reminder
Timer during a recording
Sleep Timer
Press the SLEEP/WAKE UP button
Timer Sleep Wake UP TV on ON-TIME
Wake Up Timer
Timer Sleep Wake UP
VCR Program VCR Setup Caption
Volume Bar
Menu Screen
To Adjust Press / B Caption
Closed Caption
Example
Standard Closed Captions
Closed Caption cont’d
Half-screen text
Automatic Operation Features
Glossary
Helpful Hints
Helpful Hints cont’d
Specifications
Renewed
Index
Page
Supplied Accessories
