Philips TS3659C1 manual Using the AUDIO/VIDEO Input Jacks CONT’D, Connect the S-VIDEO

Page 32

USING THE AUDIO/VIDEO INPUT JACKS (CONT’D)

S-VIDEO INPUT

The S(uper)-Video connection on the rear of the television can give you better picture detail and clarity for the playback of S-VHS VCR tapes or Digital Video Discs than the normal antenna picture connections.

Note: The VCR (or Digital Video Disc player) must have a S- VIDEO OUT(put) jack in order for you to complete the connec-

NOTE: Repeatedly pressing the AV button on the remote will toggle the picture source from the current chan- nel, to the last viewed channel, then the AV 1 connection, then the AV 2 connection.

This also applies to the Multi Media button on the remote. Repeatedly pressing the Multi Media button will toggle the picture source from the current channel, to the last viewed channel, then the MM 1 (AV 1) con- nection, then the MM 2 (AV 2) con- nection.

When using the S-Video input jack remember that it will take prece- dence over any video signal coming from the Video IN-1 jack. The sig- nal from the S-Video jack can only be viewed on the AV 1 channel.

BACK OF TV

1

tions shown on this page.

BEGIN

Connect the S-VIDEO

CABLE to the S-VIDEO input jack on the rear of the television, then connect the AUDIO (red and white) cables to the AUDIO IN (IN 1) jacks on the rear of the TV.

Connect the S-VIDEO

CABLE to the S-VIDEO output jack on the accessory device. Then, connect the red and white AUDIO CABLES to the AUDIO (left and right) output jacks on the rear of the accessory device.

 

S-VIDEO CABLE

S-VIDEO

 

 

 

 

 

 

24

(NOT SUPPLIED)

VIDEO

 

 

 

 

 

 

 

 

L

 

 

 

ANT "A"

AUDIO

 

 

 

75

R/MONO

 

 

AV 1

 

 

IN-1

OUT

 

 

 

AUDIO IN

 

 

 

(RED/WHITE)

AV 2

VIDEO IN

 

 

2

 

 

 

 

(YELLOW)

 

 

 

ANT/CABLE

S-VIDEO

R

L

 

OUT

AUDIO OUT

 

OUT

 

 

 

 

BACK OF ACCESSORY

43

Turn the VCR (or Digital

SLEEP

POWER

Video Disc Player) ON.

Press the AV button on the remote until you tune to the AV 1 channel. You are now ready to view the tape or disc on the TV.

TV

AV

STATUS/EXIT

CC

TV/VCR-CLOCK

VCR

VCR

INCREDIBLE

MULTI

A/CH

ACC

RECORD

STEREO

MEDIA

 

 

 

 

 

SMARTSMART

SOUNDPICTURE

MENUSURF

DBS, DVD, Video Game, etc.

(EQUIPPED WITH S-VIDEO AND

AUDIO OUTPUT JACKS)

IF YOU ARE USING A

NON-STEREO DEVICE,

USE ONLY THE AUDIO

R/MONO JACK.

SMART HELP

The S-VIDEO and IN-1 inputs are in parallel. The S- VIDEO input will take precedence when in use. If separate video sig-

nals are connected to the S-Video and VIDEO IN-1 inputs, the signal from the VIDEO IN-1 input will not be useable.

If you have added AV 1 to the TV’s channel memory, just press the CHANNEL + or – buttons until the AV 1 mode (channel) is selected.

VOL

CH

MUTE

32

Page 31 Page 33
Image 32
Page 31 Page 33
Contents TS3659C1 Warranty Verification Safety Instructions Read before operating equipment Table of Contents Features Cable/AntennaAdjusting the TV Picture Tings are at normal mid-range levelsSetting the TV’S Clock Timer controlsPress the Numbered buttons Press the STATUS/EXIT butActivating the TV’S on Timer Control Press the Menu button onSelecting the TV’S on Timer Channel Press the STATUS/EXIT buttonSetting the TV’S on Timer Start Time Turning on the on Timer Display Press the Cursor DownUnderstanding Smartlock Movie RatingsUsing Smartlock Setting UP the Access Code Enter current access codeDown to highlight SmartLock controlUsing Smartlock Blocking Channels Press the Channel + orThis stops the viewing of VCR, DVD, etc Select blockUsing Smartlock Movie Rating Enter the correct access code number. Xxxx shows onPress the Cursor Right Button to access the movie ratings Press the STATUS/EXIT but- ton to remove the menuUsing Smartlock TV Rating Using Smartlock Blocking OptionsUsing Smartlock Block Unrated Button or the CursorLeft button to set Block Unrated to on orUsing Smartlock no Rating Press the Menu button on the remote to show the on-screenLeft button to set no Rating to on or OFFReviewing the Smartlock Settings Example Blocking is set to OFFViewing Blocked Programming XxxxTurning on the Noise Reduction Control Press the Cursor UP or Cursor Down buttons toTurning on the Contrast + Control Trast + control Press the Cursor RightUsing the Closed Caption Control ModeUsing the Sleep Timer Control Good BYE SleepAdjusting the TREBLE, BASS, and Balance Sound Controls Setting the TV for Stereo and SAP Programs Remember, if stereo is not presentOn a selected show and the TV is Placed in the Stereo mode, the sound comUsing the Incredible Stereo Control Using the Volume BAR ControlRound TialUse the Cursor Left or Right buttons to set Setting the Audio OUT ControlAudio OUT Using the TV Speaker Control and Audio Output Jacks Connect the Right and LeftPress the Cursor Down button to select the Speakers Use the Cursor Right or Cursor Left buttonsUsing the AUDIO/VIDEO Input Jacks Connect the Video yellowTurn the VCR or Digital Using the AUDIO/VIDEO Input Jacks CONT’DConnect the S-VIDEO Using the Smart Picture Control Using the Smartsound Control Press the Smart Sound butUsing the Channel Surf Control Remote control number for your Find your Three-Digit Code on pagesDirect Access Method Place the TV/VCR/ACC Setting the Remote Control to Operate Accessory DevicesTurn on the device by press- ing the Power button on Remote Control Direct Entry Codes Remote VCR Code noRemote Dvdcode no Using the REMOTE’S VCR Buttons TV Displays Wrong Channel or No Channels Above Tips if Something Isnt WorkingGlossary to Television Terms Index Philips Consumer Electronics Company Texas Page Limited Warranty
Top Page Image Contents