Philips TS3659C1 TV Displays Wrong Channel or No Channels Above, Tips if Something Isnt Working

Page 42

TIPS IF SOMETHING ISN'T WORKING

Please make these simple checks before calling for ser-

vice. These tips can save you time and money since charges for TV installation and adjustment of customer controls are not cov- ered under your warranty.

No Power

No Picture

No Sound

Remote Does Not Work

TV Displays Wrong

Channel or No

Channels Above 13

CAUTION: A video source (such as a video game, Compact Disc Interactive - CDI, or TV information channel) which shows a constant non-moving pattern on the TV screen can cause picture tube damage. When your TV is continuously used with such a source, the pattern of the non-moving portion of the game (CDI, etc.) could leave an image permanently on the picture tube. When not in use, turn the video source OFF. Regularly alternate the use of such video sources with normal TV viewing.

Check the TV power cord. Unplug the TV, wait 10 seconds, then reinsert plug into outlet and push POWER button again.

Check that outlet is not on a wall switch. Be sure fuse is not blown on AC power strip.

Check to be sure the system mode switch (TV/VCR/ACC) is in the correct position when using the remote control to power the set ON.

Check antenna connections. Are they properly secured to the TV's ANT/CABLE plug?

Check the TUNER control for CABLE or ANTENNA setting.

Press the AV button on the remote to make sure the correct signal source is selected (AV 1, AV 2, SVID-R or MM 1, MM 2, MM 3).

Check the VOLUME buttons.

Check the MUTE button on the remote control.

Check the SPEAKER on-screen control. OFF position will eliminate sound at the set.

If attempting auxiliary equipment hookups, check audio jack connections.

(If Applicable) Check Audio Receiver for correct operating mode.

Check TV/VCR/ACC “System” switch on the remote. Move the switch to the TV position to operate the television.

Check batteries. Replace with AA Heavy Duty (Zinc Chloride) or Alkaline batteries if necessary.

Clean the remote and the remote sensor window on the TV.

Check the TV power cord. Unplug the TV, wait 10 seconds, then reinsert plug into outlet and push POWER button again. Be sure fuse is not blown on AC power strip.

Check to be sure TV outlet is not on a wall switch.

Repeat channel selection.

Add desired channel numbers (CHANNEL EDIT control) into TV memory.

Check to be sure the TUNER control is set to the CABLE option.

Cleaning and Care

To avoid possible shock hazard be sure the TV is unplugged from the electrical outlet before cleaning.

When cleaning the TV screen take care not to scratch or damage the screen surface (avoid wearing jewelry or using anything abrasive). Wipe the front screen with a clean cloth dampened with water. Use even, easy, vertical strokes when cleaning.

Gently wipe the cabinet surfaces with a clean cloth or sponge dampened in a solution of cool clear water. Use a clean dry cloth to dry the wiped surfaces.

Never use thinners, insecticide sprays, or other chemicals on or near the cabinet, as they might cause permanent marring of the cabinet finish.

42

Image 42
Contents TS3659C1 Warranty Verification Safety Instructions Read before operating equipment Table of Contents Features Cable/AntennaAdjusting the TV Picture Tings are at normal mid-range levelsPress the Numbered buttons Setting the TV’S ClockTimer controls Press the STATUS/EXIT butActivating the TV’S on Timer Control Press the Menu button onSelecting the TV’S on Timer Channel Press the STATUS/EXIT buttonSetting the TV’S on Timer Start Time Turning on the on Timer Display Press the Cursor DownUnderstanding Smartlock Movie RatingsDown to highlight Using Smartlock Setting UP the Access CodeEnter current access code SmartLock controlThis stops the viewing of VCR, DVD, etc Using Smartlock Blocking ChannelsPress the Channel + or Select blockPress the Cursor Right Button to access the movie ratings Using Smartlock Movie RatingEnter the correct access code number. Xxxx shows on Press the STATUS/EXIT but- ton to remove the menuUsing Smartlock TV Rating Using Smartlock Blocking OptionsLeft button to set Using Smartlock Block UnratedButton or the Cursor Block Unrated to on orLeft button to set no Using Smartlock no RatingPress the Menu button on the remote to show the on-screen Rating to on or OFFReviewing the Smartlock Settings Example Blocking is set to OFFViewing Blocked Programming XxxxTurning on the Noise Reduction Control Press the Cursor UP or Cursor Down buttons toTurning on the Contrast + Control Trast + control Press the Cursor RightUsing the Closed Caption Control ModeUsing the Sleep Timer Control Good BYE SleepAdjusting the TREBLE, BASS, and Balance Sound Controls On a selected show and the TV is Setting the TV for Stereo and SAP ProgramsRemember, if stereo is not present Placed in the Stereo mode, the sound comRound Using the Incredible Stereo ControlUsing the Volume BAR Control TialSetting the Audio OUT Control Audio OUTUse the Cursor Left or Right buttons to set Press the Cursor Down button to select the Speakers Using the TV Speaker Control and Audio Output JacksConnect the Right and Left Use the Cursor Right or Cursor Left buttonsUsing the AUDIO/VIDEO Input Jacks Connect the Video yellowUsing the AUDIO/VIDEO Input Jacks CONT’D Connect the S-VIDEOTurn the VCR or Digital Using the Smart Picture Control Using the Smartsound Control Press the Smart Sound butUsing the Channel Surf Control Remote control number for your Find your Three-Digit Code on pagesDirect Access Method Setting the Remote Control to Operate Accessory Devices Turn on the device by press- ing the Power button onPlace the TV/VCR/ACC Remote Control Direct Entry Codes Remote VCR Code noRemote Dvdcode no Using the REMOTE’S VCR Buttons TV Displays Wrong Channel or No Channels Above Tips if Something Isnt WorkingGlossary to Television Terms Index Philips Consumer Electronics Company Texas Page Limited Warranty