Philips SVB106 owner manual Picture Select, Appear at the bottom of the screen

Page 36

36 Picture Select

This feature enables you to select the picture quality of a tape.

Make sure:

●The VCR is on and is in VCR position. The VCR/TV light will appear. If it does not, press the VCR/TV button once.

●There is a tape in the VCR.

1

During tape playback, press the MENU button until

MENU 1 appears.

- M E N U 1 -

BTIMER PROGRAMMING

AUTO REPEAT	[OFF]
PICTURE SELECT

CHANNEL SET UP

CLOCK SET

LANGUAGE SELECT

AUTO SATELLITE LINK

2

Press the PLAY button or the STOP button repeatedly to choose PICTURE SELECT. Then, press the F.FWD but- 1 ton. The menu will disappear, and a Picture Select setting will

appear at the bottom of the screen.

- M E N U 1 -

TIMER PROGRAMMING

AUTO REPEAT

[OFF]

BPICTURE SELECT CHANNEL SET UP CLOCK SET LANGUAGE SELECT AUTO SATELLITE LINK

3

Within five seconds, press the F.FWD button until your desired setting (NORMAL, SOFT or SHARP) appears on the screen. The setting will disappear from the screen in about five seconds.

[NORMAL]

3 2

Helpful Hint

•You may only choose PICTURE SELECT during tape playback.

Image 36

Contents

Video Cassette Recorder Warranty Verification For Customer UseFeatures Safety PrecautionsIntroduction Declaration of ConformityTable of Contents Before Using Your VCR Putting Batteries in the Remote ControlUsing the Remote Control VCR maintenanceHookups Without a Cable Box/Direct Broadcast System Disconnect the antenna or cable from your TVPlug in the AC power cords of the TV and the VCR Hookups Without a Cable Box/Direct Broadcast System cont’dHookups With a Cable Box/Direct Broadcast System ConnectionsRecording/Viewing Any Channel Cable Box/DBS RF coaxial Signal Recording One Channel/Watching AnotherTV’s Antenna Jack Hookups With a Stereo TV Turning on Your VCR Below will appearAutomatic Channel Setup Press the Menu button until Menu 1 appearsAutomatic Channel Setup cont’d Adding/Deleting ChannelsSetting the Clock Follow the steps below to set your VCR’s clock. Make sureSetting the Clock cont’d Press the Counter RESET/EXIT button to exit Language SelectionOFF mode Press the Display button once. Count mode Press the Display button once Clock modePress the Display button once OFF mode On-Screen Status DisplaysRemote Control Buttons Power ButtonNumber Buttons Record ButtonCounter RESET/EXIT Button Eject ButtonTime Search Button Index Search ButtonVCR Display Panel Front Panel AC Power Cord Rear PanelAudio OUT Jacks Video OUT JackPlaying VHS Quasi Play Back SqpbRead and follow the steps below to play a tape Recording One-Touch Recording Starting an OTRStopping an OTR Timer Recording Channels are set up Clock is setTimer Recording cont’d Repeat the procedure in to set the recording’s end timeEnter the recording’s start time Start Time END Time Channel REC Speed SLP Timer Recording cont’d Cancelling a Timer RecordingCorrecting a Timer Recording Auto Satellite Link Using a Satellite Tuner Recording One Channel/Watching Another Rerecording Tape Duplication Repeat Play Forward and Reverse Searching SP/LP/SLP Super High Speed Searching LP/SLPViewing a Still Picture Viewing a Slow Motion PicturePicture Select Appear at the bottom of the screenReal-Time Counter Memory Press the Play button to watch the tapeIndex Search Press the Index Search buttonTime Search Press the Time Search buttonQuick Find Press the QUICK-FIND buttonTo resume normal tape playback, press the Play button Automatic Playback Features MTS Broadcast Stereo System Understanding On-Screen DisplaysMonitor Or ReceiverMTS Broadcast Stereo System cont’d Press the Menu button repeatedly until Menu 2 appearsPress the Counter RESET/EXIT button Hi-Fi Stereo Sound SystemPlease see additional notes on Glossary Cable Box/DBS Output Channel Channel 3 orHelpful Hints Helpful Hints cont’d Renewed Specifications Power 17-18 Recording TimerSecond audio 12, 33 BroadcastSupplied Accessories