8. | TROUBLESHOOTING |
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| SYMPTOM |
|
|
|
| CHECK POINT & CORRECTION |
|
| Cassette cannot be inserted. | • Load cassette in direction indicated by arrow on cassette. | ||||||||||
|
|
|
|
|
|
|
|
| • A cassette is already in theVCR. | ||||
|
|
|
|
|
|
|
|
| • Check if power indicator is lit on theVCR indicator panel. If not, make sure power cord is plugged | ||||
|
|
|
|
|
|
|
|
| in. |
|
|
| |
|
|
|
|
|
|
|
|
| • If the |
|
|
| indicator flashes, press the POWER button again. |
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
| ||||||||||
|
| TheVCR will not go into the | • The cassette has had the erase prevention tab removed. Stick a piece of cellophane tape over the | ||||||||||
|
| recording mode, even when REC | erase prevention tab hole or select a different cassette. | ||||||||||
|
| button is pressed. | |||||||||||
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
| ||||||
|
| No picture appears on monitor | • Try a different cassette tape. | ||||||||||
|
| screen when PLAY button is | |||||||||||
|
|
|
|
|
|
| |||||||
|
| pressed. | • Check if the system is connected right. | ||||||||||
|
|
|
| ||||||||||
|
| No picture, but audio is clear. | • The heads may require cleaning. | ||||||||||
|
|
|
|
|
|
|
|
| • TakeVCR to a qualified Service Center for service. | ||||
|
|
|
| ||||||||||
|
| Interference on playback picture. | • Adjust fine tuning knob on monitor set to obtain best picture. | ||||||||||
|
|
|
|
|
|
|
|
| • Adjust TRACKING control button. | ||||
|
|
|
|
|
|
|
|
| • TakeVCR to Service Center for service. | ||||
|
|
|
|
|
|
|
|
|
| ||||
|
| VCR does not start at preset record | • Is power button switched to off. | ||||||||||
|
| • Setup recording time according to instructions. | |||||||||||
|
| starting time. | |||||||||||
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
| ||||||
|
| The tape is ejected in the timer or | • The cassette has had the erase prevention tab removed. Stick a piece of cellophane tape over the | ||||||||||
|
| alarm recording mode. | |||||||||||
|
|
|
|
|
|
|
|
| erase prevention tab hole or select a different cassette. | ||||
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
| indication flashes. | • Insert a cassette. | ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
Using the RESET button (located at the rear panel of VCR)
This button should be used to solve the following symptoms; When the power can not on, even if power cord is connected to the outlet.
When the VCR’s display does not display. When the VCR does not operate normally.
- Use a pencil or
Warning: System will go to default settings.