Philips VRZ360 owner manual Setting the Remote Control to Operate a TV, Find the code for your TV

Page 26

VRZ360 4/7/99 9:53 PM Page 26

26 Setting the Remote Control to Operate a TV

Your VCR remote control may operate your TV. Follow these steps to set the remote control code.

1

Point the remote control at your TV. Press the TV but- ton, then press the POWER button. If your TV turns on or off, try the CH(annel) 8/9 buttons. If your remote control oper- ates the TV, you’re finished. If your TV doesn’t turn on or off, or if the CH(annel) 8/9 buttons don’t work, go to step 2.

2

Find the brand of your TV on the list below, and remem- ber the two-digit number beside it.

TV CODES

2 Find the code for your TV.

1	TV			VCR
	CBL/DBS	–	+	POWER

	MENU STILL/SLOW			cEJECT
	EXIT/STATUS	REW	PLAY	FF /OK
	EXIT/STATUS	REW	:	FF /OK
		;;		::
			L
	TIMER [REC/OTR		STOP	S.SEARCH
	TIMER [REC/OTR			S.SEARCH
	1	2	3
	+	+

EMERSON . . . . . . . . . . . . .14 GOLDSTAR . . . . . . . . . . . .04 HITACHI . . . . . . . . . . . . . .12 JVC . . . . . . . . . . . . . . . . . .05 MAGNAVOX . . . . .01, 02, 03 MITSUBISHI . . . . . . . . . . . .13 PANASONIC . . . . . . . .07, 17 PHILIPS . . . . . . . . . . . . . . .01 PHILIPS MAGNAVOX . . . . . .

. . . . . . . . . . . . . . . .01, 02, 03

RCA . . . . . . . . . . . . . . . . . .10 SAMSUNG . . . . . . . . . . . . .18 SANYO . . . . . . . . . . . . . . .11 SHARP . . . . . . . . . . . . . . . .16 SONY . . . . . . . . . . . . . . . .09 TOSHIBA . . . . . . . . . . . . . .08 ZENITH . . . . . . . . . . . .06, 15

START	STOP	DATE	CH	3
4	5	6
–		–
DBS	DAILY	WEEKLY
7	8	9
	0		VOL
SPEED	0	CLEAR

QUICK PROGRAMMING

VCR/TV 7;;INDEX ::7 AUDIO/MUTE

3

While you press and hold the TV button, use two

Number buttons to enter the two-digit code for your TV.

For example, if you have a Zenith TV, press Number buttons 1, 5.

Then, still holding the TV button, press the STOP 9 but-

4

Repeat step 1.

If the remote control works your TV, you’re finished. If the remote control still doesn’t work your TV, repeat steps 2 - 3, using a different code for your brand.

Helpful Hints

• If you had to program the remote control to operate your TV, whenev- er you replace the batteries in the remote control, you will have to pro- gram the remote control again.

• There is no guarantee that the remote control will work your TV.

Image 26

Contents VRZ360 Dear Philips Magnavox product owner For Customer UseIntroduction FeaturesSafety Precautions Table of Contents Before Using Your VCR Hookups Without a Cable Box Disconnect the antenna or cable from your TVHookups Without a Cable Box cont’d CH3 CH4Recording/Viewing Any Channel Hookups With a Cable Box/Direct Broadcast SystemConnections Cable Box/DBSWith this connection Cable signal Cable Box/DBSRecording One Channel/Watching Another TV’sTurning on Your VCR Press the FF /OK button. The menu shown below will appearAutomatic Channel Setup Press the VCR button, then press the Menu buttonAutomatic Channel Setup cont’d Adding/Deleting ChannelsManual Clock Setting Instructions continue onPress the EXIT/STATUS button Setting the Clock cont’dWhen the month and day are correct, press the FF /OK button Time Zone Selection Press the FF /OK button repeatedly to select TimeManual PBS Channel Selection Automatic PBS Channel Selection Daylight-Saving Time Press the VCR button, then press the Menu buttonLanguage Selection Press the EXIT/STATUS buttonRemote Control Buttons EXIT/STATUS Button Timer ButtonMenu Button Speed ButtonDisplay Panel Front Panel Rear Panel Operation If on Screen Mode is set to on or CounterOn the screen Setting the Remote Control to Operate a TV Find the code for your TVSetting the Remote Control to Operate a Cable Box/DBS Find the code for your Cable Box/DBSIf playback does not start automatically, press the Play PlayingRead and follow the steps below to play a tape Button. The 3 light will appear on the VCR display panelPress the VCR button VCR records in a preset volumeRecording Light will appear on the VCR display panelStarting an OTR Channels are set up. Details are on pages 11One-Touch Recording Stopping an OTRRecording One Channel/Watching Another Station Setting Up the VCR Plus+ Programming SystemChannels Setting Up the VCR Plus+ Programming System cont’d 2Examine the lists onTimer Recording With the VCR Plus+ Programming System Press the EXIT/STATUS button. Program WAS COM Complete each step within 60 seconds of the previous step Press the VCR button, then press the Timer buttonQuick Programming Standard Play Tape SpeedsTape Speed Maximum Record/Playback Time T160 T120 T60 Long PlayQuick Programming cont’d Checking, Editing, or Clearing Timer Programmed timer recordings will appearTimer Recording Speed Setting Follow the steps below to set Timer REC Speed to AutoAudio and video cables are not included Rerecording Tape DuplicationVCR 1 will play your tape. Insert a prerecorded tape in VCR Index Search Receiving a Second Audio Program Multi-Channel Television Sound SystemReceiving a Stereo Broadcast Multi-Channel Television Sound System cont’d Hi-Fi Stereo Tape Playback Video Stabilizer Incredible Picture Viewing a Still Picture Playback OptionsForward and Reverse Searching Viewing a Slow Motion PictureAutomatic Operation Features Glossary Cable Box/DBS Output Channel channel 03 orSpecifications Helpful Hints Helpful Hints cont’d Limited Warranty Model # Serial #Slp Antenna in jack With a stereo TV Ac power cord Hookups Slow motion AccessoriesGlossary Stabilizer Safety precautions Tapes Helpful hints ClearingSupplied Accessories