Philips VRX442, VRX462 warranty Press the Number 1 button to select YES, Change the VCR Channels

Page 46

46 Setting the Controller to Operate a DSS Receiver (cont’d)

6

Press the MENU button.

SELECT OUTPUT CH

OF YOUR DSS RECEIVER

0-

CBL/DSS

VCR

TV

 

 

 

TO END PUSH EXIT

EJECT

POWER

MUTE

7

A zero will appear in the SELECT OUTPUT CH menu. Press one Number button (3 or 4) to complete the out- put channel of your DSS Receiver (channel 03 or 04).

Press 0 if you connected the VIDEO/AUDIO OUT Jacks of the DSS Receiver to the VCR’s VIDEO/AUDIO IN Jacks. A/V will appear on-screen as the output channel. A/V CONNECT A/V REAR ONLY will appear.

If you make a mistake, press the CLEAR button, then enter the correct output channel.

SELECT OUTPUT CH

OF YOUR DSS RECEIVER

03

TO CONTINUE PUSH MENU

TO CORRECT PUSH CLEAR

TO END PUSH EXIT

8

Press the MENU button.

9

A four will appear in the menu. Use the Number buttons to enter the second digit of the two-digit code for your DSS Receiver. (See the list on page 44.)

SELECT CODE NUMBER OF YOUR DSS RECEIVER

42

TO TEST PUSH MENU

DID DSS RECEIVER

CHANGE TO CHANNEL 205?

1 YES 2 NO

TO END PUSH EXIT

10

Press the MENU button. Wait for the DSS Receiver to change to channel 205. When it does, go to step 11.

If the DSS Receiver does not change to channel 205, press the Number 2 button to select NO. Repeat steps 9 - 10. If the DSS Receiver doesn’t change to channel 205, the Controller will not operate your DSS Receiver. Press the EXIT/STATUS button.

11

Press the Number 1 button to select YES.

“DSS RECEIVER CONTROL IS ON” will appear for five seconds. The screen will return to the program you were watching.

 

VOL

F.ADV

CHANNEL

 

 

 

PAUSE/STILL

 

 

 

PLAY

 

 

 

REW

 

FF

 

 

VCR PLUS+

LIGHT

6

 

/ENTER

 

 

 

STOP

 

11 EXIT/STATUS MENU

CLEAR

9

1

2

3

8

7

8

9

10

7

4

5

6

 

 

100

0

GO-TO

 

 

REC/OTR

INDEX

MEMORY

 

 

 

...

 

 

 

 

...

 

 

 

 

VAR. SLOW

TRACKING SKIP

 

 

SPEED VCR/TV SLOW

SEARCH

 

REMOTE LOCATOR

Helpful Hints

If your DSS Receiver does not respond to the code in steps 9 - 10, the Controller will not change chan- nels at the DSS Receiver during a timer recording. In this case, you must select the channel to be recorded at the DSS Receiver before a timer recording begins. Leave the DSS Receiver on for the timer recording. Details are on page eight.

If more than one code is listed for your brand of DSS Receiver, try all of the codes at steps 9-10 before you determine the Controller will not

change the VCR Channels.

Image 46
Contents Video Cassette Recorder VRX442 VRX462 Dear Philips Magnavox product owner For Customer UseSafety Precautions FeaturesIntroduction Table of Contents Using the Remote Control Before Using Your VCRPutting Batteries in the Remote Control VCR MaintenanceHookups Without a Cable Box Disconnect the antenna or cable from your TVHookups Without a Cable Box cont’d Antenna Or CableRecording or Viewing a Scrambled or Unscrambled Channel Timer RecordingsHookups With a Cable Box/DSS Receiver Watching TV With the VCR Turned OffPlaying a Tape Hookups With a Cable Box/DSS Receiver cont’dRecording One Channel/Watching Another Antenna in Jack On back of TVVCR will come on and the menu shown below will appear Turning on Your VCRTurn on the TV Press the Menu button. The menu shown below will appear Wait for the VCR to program channelsProgramming Channels Press the Number 3 button to select Tuner SET UPOn the display panel of the VCR Press the Menu button to bring up the main menu display Adding/Deleting ChannelsPress the VCR button Press the Number 4 button to select ADD/DELETE CHPress the Number 3 button to select SET Manual Clock Setting the ClockPress the VCR button, then press the Menu button Press the EXIT/STATUS buttonTime Zone Selection Press the Number 4 button to select SET Time ZoneSetting the Clock cont’d Manual PBS Channel SelectionTurn off the VCR Automatic PBS Channel SelectionPress the EXIT/STATUS button. You will be prompted to ChannelsDaylight-Saving Time Selection Press the EXIT/STATUS button to exitLanguage Press the Number 2 button to select VCR SET UPLanguage Selection Press the Number 3 button to select LanguageRemote Control Buttons VCR PLUS+/ENTER Button Rame ADVance ButtonStop Button EXIT/STATUS ButtonDisplay Panel VRX462Remote Sensor Display Panel cont’dOTR Light Tape Speed Lights Memory LightFront Panel Rear Panel Setting the Remote Control to Operate a TV Find the code for your TV Repeat stepCable BOX/DSS Receiver Codes Find the code for your Cable Box/DSS Receiver Repeat stepSound Program Press the Number 2 button to select on Screen ModeOn-Screen Status Displays On Screen On and Counter Only modesTo program the VCR to find its Remote control only When you find the remote control, point the remote atRemote Locator Read and follow the steps below to play a tape PlayingTurn on the TV Insert a tape Appear on the display panel VCR records in a preset volumeRecording Stop. Details are onStopping an OTR One Touch RecordingStarting an OTR Tape Speed button. Details are on pages 36Press the RECord/OTR button to start a recording Recording One Channel/Watching AnotherInstructions carefully Select a once, daily or weekly recording Timer RecordingPress the Number 1 button to select Program RecordingFollow the instructions in to set the recording’s stop time Instructions continue onThen turn itself off Timer Recording cont’d Tape SpeedsChecking or Clearing Timer Recordings TV Channels Cable Channels Setting Up the VCR Plus+ Programming SystemLocal TV Stations Call letters Examine the lists on 2pageSelect a ONCE, DAILY, or Weekly recording Monday through FridayPress the EXIT/STATUS button. Program WAS COM Connecting the Controller Cable Box or DSS Receiver ControllerPress the Number 5 button to select SET Cable BOX Timer recordingPress the Menu button Press the Menu button or the EXIT/STATUS button Press the Menu button. Wait for a few secondsNumber 2 button to select NO. Use the Number buttons to Cable BOX Control is on will appear for five secondsPress the Number 1 button to set the DSS Receiver Setting the Controller to Operate a DSS ReceiverPress the Number 6 button to select SET DSS Receiver Controller to onPress the Number 1 button to select YES Change the VCR ChannelsVCR 1 will play your tape. Insert a prerecorded tape in VCR Rerecording Tape DuplicationTo the Audio in Jack on VCR Index Search Receiving a Stereo Broadcast These features are not available with the VRX442Receiving a Second Audio Program Multi-Channel Television Sound System VRX462 only cont’d Press the Number 1 button so that on appears besideHi-Fi Stereo Tape Playback VRX462 only Memory light will appear on the display panel Using the Tape CounterTape Counter Memory Turned ON. Details are onGo-To Feature To remove the Goto display, press the GO-TO button againPlay mode Repeat PlaybackVideo Stabilizer Video StabilizerViewing a Still Picture Playback OptionsForward and Reverse Searching Viewing a Slow Motion PictureAutomatic Operation Features Glossary Cable Box/DSS Receiver Output Channel channel 03 orSpecifications Helpful Hints Helpful Hints cont’d Renewed Off mode Ac power cord Hi-fi stereo playback Rewind buttonSafety precautions Automatic With a stereo TV Playback Manually On mode TimerSupplied Accessories