Philips VRB612AT, VRB412AT owner manual Hookups without a Cable Box/Direct Broadcast System

Page 6

6 Hookups without a Cable Box/Direct Broadcast System

The basic VCR/TV connection – antenna/cable to VCR to TV – is shown below. If you have a Cable Box or a Direct Broadcast System, please see pages eight-nine. If you have a Stereo TV, please see page 10. After you hook up the VCR, go to page 11 to turn on the VCR. (The VRB612 is illustrated here. The VRB412 has single AUDIO IN/OUT jacks.)

1

Disconnect the antenna or cable from your TV.

Antenna

Indoor/Outdoor

(300 ohm)

75V
ANT	/
CABLE

OR

Cable

(75 ohm)

75V

ANT /

CABLE

ANTENNA IN

Jack

(on back of

TV)

2

Connect the antenna or cable to the ANT(enna) IN Jack of your VCR.

Antenna

Indoor/Outdoor

(300 ohm)

OR

Cable

(75 ohm)

Back of VCR

			AUDIO		ANT
			L		IN
			L
			OUT	IN
			R
		ANT	VIDEO		OUT
			OUT	IN CH3 CH4
AUDIO
AUDIO		IN
	L	IN
	L
OUT	IN
	R
VIDEO		OUT
VIDEO
OUT	IN CH3	CH4

Image 6

Contents VRB412AT VRB612AT Dear Philips product owner For Customer Use Introduction Features Safety Precautions Declaration of ConformityTable of Contents Before Using Your VCR Hookups without a Cable Box/Direct Broadcast System Disconnect the antenna or cable from your TVHookups without a Cable Box/Direct Broadcast System cont’d Plug in the TV and the VCRHookups with a Cable Box/Direct Broadcast System ConnectionsRecording/Viewing Any Channel Hookups with a Cable Box/Direct Broadcast System cont’d Recording One Channel/Watching AnotherHookups with a Stereo TV VRB612VRB412 Press the VCR button, then press the Power button Turning on Your VCRAutomatic Channel Setup Press the VCR button Press the Menu buttonVRB612 only Adding/Deleting Channels Press the STATUS/EXIT buttonReviewing Memorized Channels Press the STATUS/EXIT button once or twice to exitSetting the Clock Manual Clock SettingDo each step within 60 seconds of the previous step Setting the Clock cont’d Enter a 0 before a single-digit numberAutomatic Clock Setting Press the VCR button, then press the Menu buttonTime Zone Daylight-Savings Time Press the VCR buttonLanguage Selection Setting the Remote to Operate a TV TV Codes2Find VCR Button VOLume o/p Button Press to adjust the volume of your TVEject Button Menu ButtonRemote Control Buttons cont’d TV ButtonIf you select Status ON, then select Counter only OFF Status Display example onlyIf you select Status ON, then select Counter only on If you select Status OFFVCR Light Timer LightVCR Display Panel Cassette CompartmentFront Panel Rear Panel Playing VHS Quasi Play Back SqpbRecording VCR light does not appear, press the VCR/TV button onceRecording One Channel/Watching Another One-Touch Recording OTR CH12Timer Recording DailyTimer Recording cont’d Time OFF To Correct Push Clear To END Push ExitPress the STATUS/EXIT button. Program WAS COM Tape SpeedsChecking or Cancelling Timer Recordings Rerecording Tape Duplication RF coaxial cableVCR SET UP, then press the F.FWD/B button Repeat PlayPress the F.FWD/B button so that on appears beside Real-Time Counter Memory Press the STATUS/EXIT button to see the status displayTime Search Press the VCR button Press the Time Search buttonSuper High Speed Searching LP/SLP Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Viewing a Still PictureAutomatic Operation Features Multi-Channel Television Sound System VRB612 only Understanding On-Screen DisplaysMulti-Channel Television Sound System VRB612 only cont’d Press the RECord/OTR button to start recordingHi-Fi Stereo Sound System VRB612 only Blue Background Helpful Hints Helpful Hints cont’d Glossary Cable Box/DBS Output Channel 03 orSpecifications Renewed Index AutomaticPage Page Page Supplied Accessories