Philips VRB412AT, VRB612AT owner manual Hookups without a Cable Box/Direct Broadcast System cont’d

Page 7

Hookups without a Cable Box/Direct Broadcast System (cont’d) 7

3

Connect the RF coaxial cable (supplied) to the OUT Jack on the back of the VCR and to the ANTENNA IN Jack on the TV. (You may use either a snap-on

type (supplied) or screw-on type of coaxial cable, whichever you prefer.)

Antenna or Cable

	AUDIO		ANT
		L	IN
	OUT	IN
		R
ANT	VIDEO		OUT
	OUT	IN CH3 CH4

AUDIO		IN
L		75V
L		ANT	/
OUT	IN	CABLE
OUT	IN
R
VIDEO		OUT
VIDEO			ANTENNA IN Jack
			ANTENNA IN Jack
OUT	IN CH3 CH4		(on back of TV)
OUT	IN CH3 CH4	RF coaxial cable	example only
		RF coaxial cable

4

Plug in the TV and the VCR.

5

Set the CH3/CH4 switch on the back of the VCR to CH3 or CH4, whichever channel is not used or least used in your area. Set the TV to the same channel. For example, when playing a tape, if the CH3/CH4 switch is set to CH3, the TV should be on channel 03.

	CH	4
	or	3
	CH	3
	CH

CH3 / CH4

Switch

CH3 CH4

			AUDIO		ANT
			L		IN
			OUT	IN
			R
		ANT	VIDEO		OUT
			OUT	IN CH3 CH4
AUDIO
AUDIO		IN
	L	IN
	L
OUT	IN
	R
VIDEO		OUT
VIDEO
OUT	IN CH3	CH4

6

You are ready to turn on the VCR. Please go to page 11 before turning on the VCR.

Image 7

Contents VRB412AT VRB612AT For Customer Use Dear Philips product ownerDeclaration of Conformity FeaturesSafety Precautions Introduction Table of Contents Before Using Your VCR Disconnect the antenna or cable from your TV Hookups without a Cable Box/Direct Broadcast SystemPlug in the TV and the VCR Hookups without a Cable Box/Direct Broadcast System cont’dConnections Hookups with a Cable Box/Direct Broadcast SystemRecording/Viewing Any Channel Recording One Channel/Watching Another Hookups with a Cable Box/Direct Broadcast System cont’dVRB612 Hookups with a Stereo TVVRB412 Turning on Your VCR Press the VCR button, then press the Power buttonPress the VCR button Press the Menu button Automatic Channel SetupVRB612 only Press the STATUS/EXIT button Adding/Deleting ChannelsPress the STATUS/EXIT button once or twice to exit Reviewing Memorized ChannelsManual Clock Setting Setting the ClockDo each step within 60 seconds of the previous step Enter a 0 before a single-digit number Setting the Clock cont’dPress the VCR button, then press the Menu button Automatic Clock SettingTime Zone Press the VCR button Daylight-Savings TimeLanguage Selection TV Codes Setting the Remote to Operate a TV2Find Menu Button VOLume o/p Button Press to adjust the volume of your TVEject Button VCR ButtonTV Button Remote Control Buttons cont’dIf you select Status OFF Status Display example onlyIf you select Status ON, then select Counter only on If you select Status ON, then select Counter only OFFCassette Compartment Timer LightVCR Display Panel VCR LightFront Panel Rear Panel VHS Quasi Play Back Sqpb PlayingVCR light does not appear, press the VCR/TV button once RecordingRecording One Channel/Watching Another OTR CH12 One-Touch RecordingDaily Timer RecordingTime OFF To Correct Push Clear To END Push Exit Timer Recording cont’dTape Speeds Press the STATUS/EXIT button. Program WAS COMChecking or Cancelling Timer Recordings RF coaxial cable Rerecording Tape DuplicationRepeat Play VCR SET UP, then press the F.FWD/B buttonPress the F.FWD/B button so that on appears beside Press the STATUS/EXIT button to see the status display Real-Time Counter MemoryPress the VCR button Press the Time Search button Time SearchViewing a Still Picture Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Super High Speed Searching LP/SLPAutomatic Operation Features Understanding On-Screen Displays Multi-Channel Television Sound System VRB612 onlyPress the RECord/OTR button to start recording Multi-Channel Television Sound System VRB612 only cont’dHi-Fi Stereo Sound System VRB612 only Blue Background Helpful Hints Helpful Hints cont’d Cable Box/DBS Output Channel 03 or GlossarySpecifications Renewed Automatic IndexPage Page Page Supplied Accessories