Yamaha DSP-AX463 53 En, Center speaker equalizer Dcenter GEQ, Audio settings Gaudio SET

Page 55

■Center speaker equalizer D)CENTER GEQ

Use this feature to adjust the built-in 5-frequency band (100Hz, 300Hz, 1kHz, 3kHz and 10kHz) graphic equalizer for the center channel so that the tonal quality of the center speaker matches that of the front speakers. You can make adjustments while listening to the currently selected source component or a test tone.

Control range: –6.0 to +6.0 dB

Control step: 0.5 dB

Initial setting: 0 dB

1 SOUND MENU

 

D)CENTER GEQ

 

TEST

>OFF

ON

. 100Hz

;;;;;;

0dB

300Hz

;;;;;;

0dB

1kHz

;;;;;;

0dB

3kHz

;;;;;;

0dB

10kHz

;;;;;;

0dB

[p]/[p]:Up/Down [p]/[[]:Adjust

Test tone TEST

Use this feature to make adjustments for “CENTER GEQ” while listening to a test tone.

Choices: OFF, ON

•Select “OFF” to stop test tones and output the currently selected source component.

•Select “ON” to output test tones from the center and front left speakers.

■Low-frequency effect level E)LFE LEVEL

Use this feature to adjust the output level of the LFE (low- frequency effect) channel according to the capacity of your subwoofer or headphones. The LFE channel carries low-frequency special effects which are only added to certain scenes. This setting is effective when the input signal contains the LFE channel.

Control range: –20 to 0 dB

Control step: 1 dB

1 SOUND MENU

E)LFE LEVEL

.SPEAKER;;;;;;0dB HEADPHONE;;;;0dB

[p]/[p]:Up/Down [p]/[[]:Adjust

Speaker SPEAKER

Adjusts the speaker LFE level.

Headphone HEADPHONE

Adjusts the headphone LFE level.

Note

Depending on the settings of “LFE/BASS OUT” (see page 51), some signals may not be output at the SUBWOOFER OUTPUT jack.

SET MENU

■Dynamic range F)DYNAMIC RANGE

Use this feature to select the amount of dynamic range compression to be applied to your speakers or headphones. This setting is effective only when this unit is decoding Dolby Digital and DTS signals.

1 SOUND MENU

F)DYNAMIC RANGE

.SPEAKER;;;;;;MAX HEADPHONE;;;;MAX

[p]/[p]:Up/Down [p]/[[]:Adjust

Speaker SPEAKER

Adjusts the speaker compression.

Headphone HEADPHONE

Adjusts the headphone compression.

Choices: MIN, STD, MAX

•Select “MIN” (minimum) if you regularly listen at low volume levels.

•Select “STD” (standard) for general use.

•Select “MAX” (maximum) to preserve the greatest amount of dynamic range.

■Audio settings G)AUDIO SET

Use this feature to adjust the overall audio settings of this unit.

1 SOUND MENU

G)AUDIO SET

.MUTE TYPE;;;FULL A.DELAY;;;;;;0ms MAX VOL.;;;+16dB INIT.VOL.;;;;OFF

[p]/[p]:Up/Down [p]/[[]:Select

Mute type MUTE TYPE

Use this feature to adjust how much the mute function reduces the output volume (see page 34).

Choices: FULL, –20dB

•Select “FULL” to completely mute all the audio output.

•Select “–20dB” to reduce the current volume by 20 dB.

Audio delay A.DELAY

Use this feature to delay the sound output and synchronize it with the video image. This may be necessary when using certain LCD monitors or projectors.

Control range: 0 to 160 ms

Control step: 1 ms

OPERATION

ADVANCED

 

 

English

53 En

Page 54 Page 56
Image 55
Page 54 Page 56
Contents DSP-AX463 Special Instructions for U.K. Model For U.K. customersContents Features Getting started Press Scene 1 button Enjoy DVD playback Set up your speakersQuick start guide Preparation Check the itemsSurround speakers Front and center speakersFor further connections Press Scene 1 button Default assigned Scene templatesAbout Scene function What do you want to do with this unit? Rear panel ConnectionsName 10 En Placing speakersSurround speakers Right Left Connecting speakers11 En Front B terminals10 mm 3/8 Before connecting to the Speakers TerminalConnecting to the Speaker terminals 12 EnVideo jacks Information on jacks and cable plugs13 En Audio jacksInformation on Hdmi Audio and video signal flow14 En 15 En Connecting video componentsDVD player Connecting other componentsConnecting a DVD player 16 EnPVR or VCR Connecting a DVD recorder, PVR or VCRConnecting a set-top box 17 En18 En Connecting audio componentsConnecting a CD player, a CD recorder Connecting a multi-format player or an external decoder19 En Using the Video AUX jacks on the front panelGame console or Video camera Turning on this unit Connecting the power cable Turning on and off the powerSet this unit to the standby mode 20 En21 En Front panel display22 En Using the remote controlMake sure of the following check points Optimizing the speaker setting for your listening roomUsing Auto Setup 23 En24 En Speaker level LVL 25 EnNumber of speakers SP Speaker distance DistIf Warning appears If an error screen appearsPress 7n and then press 7l / h to select SET or Cancel 26 EnSelected Scene template is assigned to the button Selecting the Scene templatesSelecting the desired Scene template 27 EnWhich Scene template would you like to select? 28 En29 En Preset Scene templates descriptionsRenaming the Scene templates Customizing the preset Scene TemplatesCreating your original Scene templates 30 EnControlling the input source Components in the Scene mode Using remote control on the Scene feature31 En 32 En Quick guide to contentsPlayback Basic operationsSelecting the Multi CH Input component Selecting audio input jacks33 En Current status screen appears in the OSD Using your headphonesMuting the audio output 34 EnVideo information Displaying the input source information35 En Audio information36 En Using the sleep timerSound field program descriptions Sound field programs37 En Enjoying unprocessed input sources Straight decoding mode Enjoying 2-channel sources using Standard decoders38 En Editing sound fields parameters 39 EnEnjoying high quality sound Using audio featuresAdjusting the tonal quality Adjusting the speaker level41 En Selecting the night listening modePress J Input l / h repeatedly or press 3USB to select USB Playback operation42 En Supported USB devicesPlayback icon All all repeat, 1 single repeat icons 43 EnFunction of the play information display Press 7ENTER to play the selected fileControlling iPod Using iPodRemote control operation Controlling iPod in the simple remote ModeShuffle Shuffle Controlling iPod in the menu browse Mode45 En Press 3V-AUX/DOCKand then46 En Using Bluetooth componentsPairing by using SET Menu Quick pairing47 En RecordingManual setup Manual Setup Auto setup Auto Setup48 En Signal information Using SET Menu49 En 50 En Speaker settings Aspeaker SET51 En Unit Unit 52 EnSpeaker level BSP Level Speaker distance CSP DistanceLow-frequency effect level Elfe Level Audio settings Gaudio SET53 En Center speaker equalizer Dcenter GEQSupport audio Support Audio Maximum volume MAX VOLInitial volume INIT.VOL 54 EnFor Optical Input jacks 2 55 EnInput assignment For Coaxial Input jack56 En Multi channel input setupDecoder select mode DTS decoder prioritize setting57 En Display settings Adisplay SET58 En Bluetooth setting Ebluetooth SETPress 7ENTER to start pairing Press 8RETURN to exit from Start PairingUSB playback styles Fusb Play Style 59 EnControlling this unit Remote control featuresControlling this unit, a TV, or other components 60 EnControlling other components 61 En62 En Setting remote control codesRemote control code default settings Input Component Manufacturer DefaultOnly a STANDBY/ON, G Program l / h Advanced setup63 En Initializing InitGeneral TroubleshootingProblem Cause Remedy See 64 En65 En 66 En During Auto Setup Before Auto Setup67 En 68 En After Auto Setup1OUT of Phase 3LEVEL ErrorUnable to play Access error69 En DisconnectedIPod 70 En71 En Bluetooth72 En Remote controlResetting the system Advanced setup menu appears in the front panel display73 En GlossaryPCM Linear PCM 74 EnLFE 0.1 channel MP375 En Specifications76 En IndexNumerics Low-frequency effect level 77 EnUnplug HP 78 EnConditions 79 EnAB C D Front panelPower USB Mute MD/CD-R Tuner DVD DTV/CBL DVR Iii List of remote control codesTape Deck LD playerITT VCR WN25770 Front panel DSP-AX463TV AV Remote control
Top Page Image Contents