Yamaha DSP-AX463 Optimizing the speaker setting for your listening room, Using Auto Setup, 23 En

Page 25

Optimizing the speaker setting for your listening room

This unit employs the YPAO (Yamaha Parametric Room Acoustic Optimizer) technology which lets you avoid troublesome listening-based speaker setup and achieves highly accurate sound adjustments automatically. The supplied optimizer microphone collects and this unit analyzes the sound your speakers produce in your actual listening environment.

Using AUTO SETUP

Notes

•Be advised that it is normal for loud test tones to be output during the “AUTO SETUP” procedure.

•To achieve the best results, make sure the room is as quiet as possible while the “AUTO SETUP” procedure is in progress. If there is too much ambient noise, the results may not be satisfactory.

y

You can run “AUTO SETUP” using the system menu that appears in the OSD or in the front panel display. This manual uses the OSD illustrations to explain the “AUTO SETUP” procedure.

1Make sure of the following check points.

Note

Before starting the automatic setup, check the following check points.

❏Speakers are connected appropriately.

❏Headphones are disconnected from this unit.

❏This unit and the video monitor are turned on.

❏This unit is selected as the video input source of the video monitor.

❏The connected subwoofer is turned on and the volume level is set to about half way (or slightly less).

❏The crossover frequency controls of the connected subwoofer is set to the maximum.

VOLUME		CROSSOVER
		HIGH CUT
MIN	MAX	MIN	MAX

Controls of a subwoofer (example)

❏FRONT A speakers are selected as the front speaker system (see page 32).

❏The room is sufficiently quiet.

2Connect the supplied optimizer microphone to the OPTIMIZER MIC jack on the front panel.

OPTIMIZER MIC

		VIDEO AUX		USB
VIDEO		L AUDIO		R

AUDIO SELECT

Optimizer microphone

The following display appears in the OSD.

AUTO SETUP

SETUP;;;;;;;AUTO

.START

Automatic Processing of all item

[p]/[p]:Up/Down [p]/[[]:Select

3Place the optimizer microphone at your normal listening position on a flat level surface with the microphone heading upward.

Optimizer microphone

y

It is recommended that you use a tripod (etc.) to affix the optimizer microphone at the same height as your ears would be when you are seated in your listening position. You can use the attached screw of a tripod (etc.) to fix the optimizer microphone to the tripod (etc.).

PREPARATION

English

23 En

Image 25

Contents DSP-AX463 Special Instructions for U.K. Model For U.K. customersContents Features Getting started Quick start guide Set up your speakersPreparation Check the items Press Scene 1 button Enjoy DVD playbackSurround speakers Front and center speakersFor further connections Press Scene 1 button Default assigned Scene templatesAbout Scene function What do you want to do with this unit? Rear panel ConnectionsName 10 En Placing speakers11 En Connecting speakersFront B terminals Surround speakers Right LeftConnecting to the Speaker terminals Before connecting to the Speakers Terminal12 En 10 mm 3/813 En Information on jacks and cable plugsAudio jacks Video jacksInformation on Hdmi Audio and video signal flow14 En 15 En Connecting video componentsConnecting a DVD player Connecting other components16 En DVD playerConnecting a set-top box Connecting a DVD recorder, PVR or VCR17 En PVR or VCRConnecting a CD player, a CD recorder Connecting audio componentsConnecting a multi-format player or an external decoder 18 En19 En Using the Video AUX jacks on the front panelGame console or Video camera Set this unit to the standby mode Connecting the power cable Turning on and off the power20 En Turning on this unit21 En Front panel display22 En Using the remote controlUsing Auto Setup Optimizing the speaker setting for your listening room23 En Make sure of the following check points24 En Number of speakers SP 25 EnSpeaker distance Dist Speaker level LVLPress 7n and then press 7l / h to select SET or Cancel If an error screen appears26 En If Warning appearsSelecting the desired Scene template Selecting the Scene templates27 En Selected Scene template is assigned to the buttonWhich Scene template would you like to select? 28 En29 En Preset Scene templates descriptionsCreating your original Scene templates Customizing the preset Scene Templates30 En Renaming the Scene templatesControlling the input source Components in the Scene mode Using remote control on the Scene feature31 En Playback Quick guide to contentsBasic operations 32 EnSelecting the Multi CH Input component Selecting audio input jacks33 En Muting the audio output Using your headphones34 En Current status screen appears in the OSD35 En Displaying the input source informationAudio information Video information36 En Using the sleep timerSound field program descriptions Sound field programs37 En Enjoying unprocessed input sources Straight decoding mode Enjoying 2-channel sources using Standard decoders38 En Editing sound fields parameters 39 EnAdjusting the tonal quality Using audio featuresAdjusting the speaker level Enjoying high quality sound41 En Selecting the night listening mode42 En Playback operationSupported USB devices Press J Input l / h repeatedly or press 3USB to select USBFunction of the play information display 43 EnPress 7ENTER to play the selected file Playback icon All all repeat, 1 single repeat iconsRemote control operation Using iPodControlling iPod in the simple remote Mode Controlling iPod45 En Controlling iPod in the menu browse ModePress 3V-AUX/DOCKand then Shuffle ShufflePairing by using SET Menu Using Bluetooth componentsQuick pairing 46 En47 En RecordingManual setup Manual Setup Auto setup Auto Setup48 En Signal information Using SET Menu49 En 50 En Speaker settings Aspeaker SET51 En Speaker level BSP Level 52 EnSpeaker distance CSP Distance Unit Unit53 En Audio settings Gaudio SETCenter speaker equalizer Dcenter GEQ Low-frequency effect level Elfe LevelInitial volume INIT.VOL Maximum volume MAX VOL54 En Support audio Support AudioInput assignment 55 EnFor Coaxial Input jack For Optical Input jacks 2Decoder select mode Multi channel input setupDTS decoder prioritize setting 56 En57 En Display settings Adisplay SETPress 7ENTER to start pairing Bluetooth setting Ebluetooth SETPress 8RETURN to exit from Start Pairing 58 EnUSB playback styles Fusb Play Style 59 EnControlling this unit, a TV, or other components Remote control features60 En Controlling this unitControlling other components 61 EnRemote control code default settings Setting remote control codesInput Component Manufacturer Default 62 En63 En Advanced setupInitializing Init Only a STANDBY/ON, G Program l / hProblem Cause Remedy See Troubleshooting64 En General65 En 66 En During Auto Setup Before Auto Setup67 En 1OUT of Phase After Auto Setup3LEVEL Error 68 En69 En Access errorDisconnected Unable to playIPod 70 En71 En BluetoothResetting the system Remote controlAdvanced setup menu appears in the front panel display 72 En73 En GlossaryLFE 0.1 channel 74 EnMP3 PCM Linear PCM75 En Specifications76 En IndexNumerics Low-frequency effect level 77 EnUnplug HP 78 EnConditions 79 EnAB C D Front panelPower USB Mute MD/CD-R Tuner DVD DTV/CBL DVR Iii List of remote control codesTape Deck LD playerITT VCR WN25770 Front panel DSP-AX463TV AV Remote control