Manual Channel Setting, Selecting Colour Mode

STORE CHANNEL CONTINUE SEARCH

* If you have accidentally deleted a channel, press REW 2.

5.2: TO EXCHANGE CHANNEL POSITION: Press OK/STATUS once so that the channel number flashes. Using the number button on the remote control, enter the other channel number that you want to exchange with, then press OK/

STATUS.

5.3: TO FINE-TUNE CHANNELS

Press OK/STATUS twice so that the frequency indication flashes. Press PLAY5or STOP∞ to fine-tune the station until you get the best possible picture, then press OK/STATUS.

5.4: TO CHANGE THE TV SYSTEM: This is necessary if no sound comes out on the channel.

Press OK/STATUS three times so that the TV system indication flashes. Press PLAY5or STOP∞to select the approriate TV system (BG, DK, I) so that the sound comes out, then press OK/ STATUS.

6Press MENU to exit.

Manual Channel Setting

1Repeat steps 1-4 of “To delete or edit receivable channels” on the left column .

2Press PLAY 5or STOP ∞until a vacant channel in which you want to store a new channel starts flashing, then press OK/STATUS.

3Press PLAY 5or STOP ∞to select

the search starting band, then press OK/STATUS. VHF L: Starts searching from the VHF L band. VHF H: Starts searching from the VHF H band. UHF: Starts searching from the UHF band. Searching starts, and when a station is tuned in, searching stops and the tuned frequency is shown on the TV.

4Press PLAY 5or STOP ∞to

select “STORE CHANNEL”, then press OK/STATUS.

The programmed channel in- SELECT: CONFIRM: OK

formation list appears again	END: MENU

with the settings of the newly tuned channel flashing.

If you do not want to store the channel, select “CONTINUE SEARCH”, then press OK/ STATUS so that the search starts again.

5Press MENU to exit.

●

Selecting Colour Mode

Before using the VCR, you need to set the colour mode both for recording and playback.

Press COLOUR MODE on the front panel for more than 2 seconds. The current setting will appear on the screen for about 5 seconds. While the current setting appears, press COLOUR MODE repeatedly, the setting changes as follows.

AUTO: Normally select this mode. The colour system is automatically detected.

If “AUTO” does not work well, choose the other settings below.

NTSC3.58: To record the NTSC signals or playback an NTSC3.58 tape on an NTSC TV.

NTSC4.43: To record the NTSC signals or playback an NTSC4.43 tape on a PAL TV.

NTSC=PAL TV (ONLY FOR PLAYBACK): To playback an NTSC3.58 tape on a PAL TV.

PAL: To record PAL signals or playback a PAL TV.

MESECAM: To record SECAM signals or playback a MESECAM tape.

When playing back an NTSC tape with “AUTO” mode selected, the NTSC signal is converted to PAL signal and is played back.

Playback

❍1 On TV

1Turn on the TV.

2Select the video channel (or AV mode).

❍2 On VCR

Insert a cassette. The VCR turns on.

•If the record tab on a cassette is removed, playback will start automatically.

•If a cassette is already in the VCR, turn on the VCR.

❍3 Start Playback

Press PLAY 3.

To pause playback and view still picture, press STILL/ SLOW 0(or STILL/PAUSE on the front panel).

Press PLAY 3 to resume playback.

To rapidly locate a particular scene, press FF¡ or REW1 during playback. (No sound comes out.) Press PLAY 3 to resume playback.

To stop playback, press STOP ■.

To rewind the tape, press REW 1when the tape is not running.

To fast forward the tape, press FF ¡when the tape is not running.

To eject the tape, press 0 EJECT.

To turn off the VCR, press POWER.