Turbo Timer
This function allows you to set the timer recording program without going through the regular set up
•Tape speed can be selected by pressing the ALT/SPEED button anytime during steps 1 through 4.
The speed appears on the display for about 5 seconds.
with the on screen. The extent of programming is 24 hours from the current time.
1 Insert a tape into the VCR and press the | |
“TURBO TIMER” button on the remote control. | |
“ | ” (start time Prompt) and the current |
time appears alternately on the display. | |
When two programs overlap
The Program Review screen will appear with a magenta line blinking on the newly set timer recording while the other overlapped program blinking.
PR CH | START | STOP | DATE | |
1 | 12 | 20:00 | 22:00 | 20/07 |
2 | 20 | 11:00 | 11:30 | 15/10 |
3 | 24 | 15:00 | 16:00 | 10/08 |
4 | 45 | 21:00 | 23:00 | FRI |
5 |
|
|
|
|
6 |
|
|
|
|
7 |
|
|
|
|
8 |
|
|
|
|
SELECT: |
| CONFIRM: OK | ||
2 | To change the START time, press the PLAY 5or | ||||||||
|
| STOP ∞button (if you press and hold either | |||||||
|
| button, the time changes in | |||||||
|
| ments), then press OK/STATUS. | |||||||
|
|
|
|
| ” (stop time prompt) and the set | ||||
|
|
|
|
| |||||
|
| Then,“ |
|
| |||||
|
| start time appears alternately on the display. | |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3 | To change the STOP time, press the PLAY 5 or | ||||||||
|
| STOP ∞button (if you press and hold either | |||||||
|
| button, the time changes in | |||||||
|
| ments), then press OK/STATUS. | |||||||
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
4 | Channel number will appear on the display. | ||||||||
To change the CHANNEL number, press the | |||||||||
|
| PLAY 5or STOP ∞, then press OK/STATUS. | |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
5 | The data input will be memorized and the Turbo | ||||||||
|
| Timer mode will be finished so that normal | |||||||
|
| display appears. | |||||||
6 | Turn off the VCR. | ||||||||
Notes:
•To exit Turbo Timer mode at any step, press the TURBO TIMER button.
•If “Err” appears on the display panel, all eight programs have been set and Turbo Timer will not proceed. To remove the error message, press the TURBO TIMER button again.
•Settings of Turbo Timer will appear on the display panel only and not on the screen.
•Programs Overlap Warning does not function with Turbo Timer.
•DAILY or WEEKLY programming are not available on Turbo Timer.
1Press PLAY 5or STOP ∞to move the magenta line among the two overlapping programs.
2Press OK/STATUS to view
the detail information of the | ONE TIME PROGRAM | |
PROGRAM | 1 | |
program you want to change. | CHANNEL+/– 12 | |
START +/– | 20 : 00 | |
3 Go to step 4 through 8 to | STOP +/– | 22 : 00 |
REC SPEED | SP | |
modify the selected program. | DATE +/– | 20/07/01 |
| FRIDAY | |
ERASE: CLEAR |
| |
To cancel any timer recording, | NEXT: OK | END: TIMER |
|
| |
press CLEAR.
•If you do not modify the overlapping programs, the VCR will record the earlier program com- pletely. Only the remaining part of the later program will be recorded.
•If the START time for the two programs are the same, the lower program number will be re- corded.
Useful function for Timer Recording:
Auto Tape Speed
With this function activated, the VCR can change the tape speed and record the programme in LP or SLP mode if not enough tape remains for recording in SP mode.
1Press VCR.
2Press MENU.
3Press PLAY 5or STOP ∞to select “VCR SET UP” then press OK/STATUS.
4Press PLAY 5or STOP ∞to select “TIMER REC SPEED.”
5Press FF 3. Each time you press the button, the setting changes.
AUTO:
Select this to allow the VCR to change the tape speed from SP to LP (or SLP) when there is not enough tape length remaining.
MANUAL:
Select this not to allow the VCR to change the tape speed.
6Press MENU to exit from the menu operations.
13