Philips VR620CAT owner manual Glossary / Specifications

Page 48

48 Glossary / Specifications

Glossary

AUDIO IN/OUT Jacks: jacks on the front and back of the VCR that record audio from another source (IN) or send audio to another system (OUT).

Automatic Channel Setup: process in which the VCR mem- orizes all available channels. Then, when you press the CH(annel) o/p buttons, you only scan through channels you receive.

Bands: settings that allow you to tune channels.

•Antenna – VHF (very high frequency; channels 2-13) and UHF (ultra high frequency; channels 14-69).

•Cable – all standard channels can be received without a Cable Box.

Cable Box/DBS Output Channel: 03 or 04.

Dubbing: copying a tape using a second VCR.

Frame: a still picture.

HQ: high quality; a feature in the VCR circuitry which provides enhanced picture detail.

Line Input: The channel to which you set your VCR during dub- bing. If you use the AUDIO and VIDEO In jacks on the front of the VCR, select channel 002 (AV FRONT). If you use the AUDIO and VIDEO IN jacks on the back of the VCR, select 001 (AV REAR). If you accidentally enter Line Input mode, press the CH(annel) o/p buttons or use the Number buttons to select another channel.

OTR: One-Touch Recording; a timed recording that starts immediately and records for 30 minutes to eight hours.

Remote Control: the small electronic unit that came with your VCR; allows you to operate your VCR from a distance.

RF coaxial cable: The black cable supplied with your VCR. Use it to connect your VCR to your TV (or Cable Box or DBS). The supplied cable is a snap-on type. However, you may use a screw-on type if you prefer.

Special Effects: forward and reverse searching; a still picture; slow motion playback.

Tape Speeds: how fast the tape travels during a recording or playback.

•SP (standard play) – fastest tape speed (recording time for a T120 tape is approximately two hours); best picture quality.

•LP (long play) – average tape speed; playback only.

•SLP (super long play) – slowest tape speed (recording time for a T120 tape is approximately six hours).

VCR: video cassette recorder.

VIDEO IN/OUT Jacks: jacks on the front and back of the VCR that record video from another source (IN) or send video to another system (OUT).

Specifications

Video Heads

Four heads - Hi-Fi

Video Signal

EIA standards; NTSC color

Antenna

VHF/UHF – 75 ohm external antenna terminal

VHF Output Signal

Channel 03 or 04 (switchable) 75 ohms unbalanced

Power Requirement

120V AC; 60Hz

Power Consumption

14W

Operating Temperature

41°F (5°C) to 104°F (40°C)

Relative Humidity

10% to 80%

Weight

5.3 lbs. (2.4 kg.)

Dimensions

14-3/16” (W) x 3-5/8” (H) x 8-1/2” (D) (360mm x 92mm x 215.5mm)

Tuner Broadcast Channels

VHF 2-13, UHF 14-69

Cable TV Channels

1-125

NOTE: Designs and specifications are sub- ject to change without notice.

Page 47 Page 49
Image 48
Page 47 Page 49
Contents VR620CAT Dear Philips product owner For Customer UseFeatures Safety PrecautionsIntroduction Declaration of ConformityTable of Contents Putting Batteries in the Remote Control Battery SafetyUsing the Remote Control VCR maintenanceHookups Without a Cable Box/Direct Broadcast System Disconnect the antenna or cable from your TVHookups Without a Cable Box/Direct Broadcast System cont’d Hookups With a Cable Box/Direct Broadcast System ConnectionsRecording/Viewing Any Channel Hookups With a Cable Box/Direct Broadcast System cont’d Recording One Channel/Watching AnotherHookups with a Stereo TV Turning on Your VCR Press the Menu button. The display shown below will appearAutomatic Channel Setup Press the VCR button, then press the Menu buttonAutomatic Channel Setup cont’d Adding/Deleting ChannelsReviewing Memorized Channels Press the STATUS/EXIT button once or twice to exitSetting the Clock Enter a 0 before a single-digit numberDaylight-Savings Time Press the VCR button, then press the Menu buttonLanguage Selection Setting the Remote to Operate a TV 2TV code Find yourCable BOX Codes 2code Find yourRemote Control Buttons CHannel o/p Buttons TV ButtonOn-Screen Status Displays If you select Status ON, then select Counter only onIf you select Status ON, then select Counter only OFF If you select Status OFFVCR Display Panel Cassette CompartmentRECord Light VCR LightFront Panel Rear Panel Playing VHS Quasi Play Back SqpbRecording Insert a tape with its record tab intact in the VCRRecording One Channel/Watching Another One-Touch Recording Timer Recording DailyTimer Recording cont’d Timer Recording cont’d Tape SpeedsChecking or Cancelling Timer Recordings Rerecording Tape Duplication Repeat Play Press the PLAY/o button or the STOP/p button to selectPress the F.FWD/B button so that on appears beside Clear button to reset the real-time counter to zero Real-Time Counter MemoryWhile the status display is on the screen, press Time Search Press the VCR button, then press the Time Search but- tonSpecial Effects Playback Forward and Reverse Searching SP/LP/SLPSuper High Speed Searching LP/SLP Viewing a Still PictureAutomatic Operation Features Multi-Channel Television Sound System Understanding On-Screen DisplaysMulti-Channel Television Sound System cont’d Hi-Fi Stereo Sound System Please see additional notes onBlue Background Helpful Hints Helpful Hints cont’d Limited Warranty Video Cassette Recorder or PlayerLimited Warranty cont’d To obtain a replacement product from PhilipsPayment Amount $29.95 + Sales Tax = Total Payment, if applicableGlossary / Specifications SpecificationsGlossary Index AutomaticPage Page Supplied Accessories
Top Page Image Contents