Philips VR620CAT On-Screen Status Displays, If you select Status ON, then select Counter only on

Page 22

22 On-Screen Status Displays

A status display will appear when you press the STATUS/EXIT but- ton or certain function buttons. The contents of the status display will vary. To choose the status display mode, follow the steps below.

If you select STATUS ON, then select COUNTER ONLY ON:

●Whenever you press the STOP/p button or the PLAY/o button,

the status display will appear for five seconds. After five seconds, only the counter will remain on the screen. You must press the STATUS/EXIT button to remove it. Portions of the status display also may appear when you press other function buttons.

If you select STATUS ON, then select COUNTER ONLY OFF:

●Whenever you press the STOP/p button or the PLAY/o button, the status display will appear for five seconds. Portions of the sta- tus display also may appear when you press other function but- tons.

If you select STATUS OFF:

●The status display will not appear when you press function but- tons. You must press the STATUS/EXIT button to see the status display.

1

Press the VCR button, then press the MENU button.

2

Press the PLAY/o button or the STOP/p button to select VCR SET UP, then press the F.FWD/B button.

3

Press the PLAY/o button or the STOP/p button to select ON SCREEN MODE, then press the F.FWD/B button.

4

Press the PLAY/o button or the STOP/p button to select STATUS, then press the F.FWD/B button so that OFF (or ON) appears beside STATUS.

SELECT op CHOOSE B

→ STATUS	[ON]
COUNTER ONLY	[OFF]

TO END PUSH EXIT

5

If you set STATUS to OFF, go to step 6. If you set STA- TUS to ON, press the PLAY/o button or the STOP/p button to select COUNTER ONLY, then press the F.FWD/B button so that OFF (or ON) appears beside it.

6

Press the STATUS/EXIT button.

			Receiving,
			Recording Mode
Current								Channel
tape status					Time
					Time


STOP				12:00			AM
TV STEREO					CH10


					STEREO
					STEREO
					2ND AUD
					2ND AUD
SLP		M 1:23:45			HIFI
Tape
Tape		Counter,			Audio Out
Speed		Counter			Setting

Memory

MTS

Broadcast

Available

Helpful Hints

•You may not access a status display when viewing a still picture, during slow motion playback, or during for- ward or reverse searching.

•The status display may not appear if a weak channel is selected and BLUE BACKGROUND is set to OFF. Details are on page 43.

Image 22

Contents VR620CAT Dear Philips product owner For Customer UseIntroduction FeaturesSafety Precautions Declaration of ConformityTable of Contents Using the Remote Control Putting Batteries in the Remote ControlBattery Safety VCR maintenanceHookups Without a Cable Box/Direct Broadcast System Disconnect the antenna or cable from your TVHookups Without a Cable Box/Direct Broadcast System cont’d Connections Hookups With a Cable Box/Direct Broadcast SystemRecording/Viewing Any Channel Hookups With a Cable Box/Direct Broadcast System cont’d Recording One Channel/Watching AnotherHookups with a Stereo TV Turning on Your VCR Press the Menu button. The display shown below will appearAutomatic Channel Setup Press the VCR button, then press the Menu buttonAutomatic Channel Setup cont’d Adding/Deleting ChannelsReviewing Memorized Channels Press the STATUS/EXIT button once or twice to exitSetting the Clock Enter a 0 before a single-digit numberDaylight-Savings Time Press the VCR button, then press the Menu buttonLanguage Selection Setting the Remote to Operate a TV 2TV code Find yourCable BOX Codes 2code Find yourRemote Control Buttons CHannel o/p Buttons TV ButtonIf you select Status ON, then select Counter only OFF On-Screen Status DisplaysIf you select Status ON, then select Counter only on If you select Status OFFRECord Light VCR Display PanelCassette Compartment VCR LightFront Panel Rear Panel Playing VHS Quasi Play Back SqpbRecording Insert a tape with its record tab intact in the VCRRecording One Channel/Watching Another One-Touch Recording Timer Recording DailyTimer Recording cont’d Timer Recording cont’d Tape SpeedsChecking or Cancelling Timer Recordings Rerecording Tape Duplication Press the PLAY/o button or the STOP/p button to select Repeat PlayPress the F.FWD/B button so that on appears beside Real-Time Counter Memory Clear button to reset the real-time counter to zeroWhile the status display is on the screen, press Time Search Press the VCR button, then press the Time Search but- tonSuper High Speed Searching LP/SLP Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Viewing a Still PictureAutomatic Operation Features Multi-Channel Television Sound System Understanding On-Screen DisplaysMulti-Channel Television Sound System cont’d Hi-Fi Stereo Sound System Please see additional notes onBlue Background Helpful Hints Helpful Hints cont’d Limited Warranty Video Cassette Recorder or PlayerPayment Amount $29.95 + Sales Tax = Total Limited Warranty cont’dTo obtain a replacement product from Philips Payment, if applicableSpecifications Glossary / SpecificationsGlossary Index AutomaticPage Page Supplied Accessories