Cisco Systems AS5350 manual Replacing Sdram DIMMs, Sdram Dimm Replacement

Page 65

Appendix

Replacing SDRAM DIMMs

Replacing SDRAM DIMMs

This section describes how to replace SDRAM DIMMs on the system board. You might need to upgrade the SDRAM DIMMs for the following reasons:

You have upgraded to a new Cisco IOS feature set or release that requires more memory.

You are using very large routing tables or many protocols (for example, when the universal gateway is set up as a connection device between large external networks and your internal network).

The system board contains three sockets for SDRAM DIMMs (see Figure A-3):

Two sockets hold main memory SDRAM DIMMs. Main memory is used by the CPU to store the operating configuration, routing tables, and queues. The DIMMs can be 128 or 256 MB, and the capacity of the DIMMs in both sockets must match.

For main memory, the total capacity is 512 MB (two, 256 MB DIMMs).

One socket holds a shared memory SDRAM DIMM. Shared memory is used to store incoming and outgoing packets. This DIMM can be 64 or 128 MB.

For shared memory, the total capacity is 128 MB (one, 128 MB DIMM).

Required Tools and Equipment

You need the following tools and equipment:

ESD-preventive wrist strap

The appropriate SDRAM DIMM(s) for your universal gateway

SDRAM DIMM Replacement

To replace the SDRAMM, follow this procedure:

Step 1 Turn the power switch on the universal gateway off and disconnect site power.

Step 2 Remove all interface cables from the rear panel of the universal gateway.

Warning Before opening the chassis, disconnect the telephone-network cables to avoid contact with telephone-network voltages. To see translations of the warnings that appear in this publication, refer to the Regulatory Compliance and Safety Information document that accompanied this device.

Step 3 Attach an ESD-preventive wrist strap.

Step 4 Remove the chassis cover. (See the instructions in the “Removing the Chassis Cover” section on page A1.)

Step 5 Use Figure A-3to locate the DIMM you are replacing.

Cisco AS5350 Universal Gateway Chassis Installation Guide

 

78-10754-03 0A

-7

 

 

 

Image 65
Contents Cisco AS5350 Universal Gateway Chassis Installation Guide Cisco AS5350 Universal Gateway Chassis Installation Guide Iii PrefaceLEDs Overview B-1 78-10754-03 0A Vii Document OrganizationViii Document ConventionsDocument Conventions Document Conventions OBS! Spara Dessa Anvisningar Xii Related DocumentationObtaining Documentation New Hardware FeaturesCisco.com Documentation CD-ROMOrdering Documentation Obtaining Technical AssistanceDocumentation Feedback XivCisco TAC Website Technical Assistance CenterXvi Obtaining Additional Publications and InformationChassis Components OverviewCisco AS5350 Front Panel Dial Feature Cards DFCsChassis Specifications Power SupplySee the Regulatory Compliance and Safety Maintaining Safety with Electricity Preparing to Install the Cisco AS5350 ChassisSafety Recommendations Preventing Electrostatic Discharge Damage Preparing to Connect to a Network Required Tools and EquipmentConsole and Auxiliary Ports Ethernet ConnectionsBits Port Alarm Port2T Serial Ports Power Supply Considerations Installing the Cisco AS5350 Setting the Chassis on a Desktop Setting Up the ChassisAttaching the Rubber Feet Rack-Mounting the ChassisRequired Tools and Equipment Installing in a Rack Cisco AS5350 Ground Lug Attachment Connecting to the NetworkConnecting to a WAN Connecting to an Ethernet NetworkConnecting a 2-Port or 4-Port DFC to an RJ-45 T1 Jack Connecting an 8-Port DFC to a RJ-45 T1 Jack 10 Connecting a 2-Port or 4-Port DFC to an RJ-45 Jack Connecting to the Console Port Connecting to the Console and Auxiliary Ports13 Connecting the Console Terminal Connecting a Modem to the Auxiliary Port14 Connecting a Modem to the Auxiliary Port Connecting a Signal Generator to the Bits PortTo alarm device Cable ties Alarm port connector Connecting an Alarm to the Alarm PortAccompanied this device Supplying Power17 Connecting the AC Power Cord 19 DC Power Supply Connections-Single Power Supply 20 DC Power Supply Connections-Redundant Power Supply Where to Go Next 78-10754-03 0A LEDs TroubleshootingLED Cisco AS5350 Slot Numbering Monitoring EnvironmentDisplaying Environment Status Router# show environment Removing the Fan Tray Troubleshooting Network InterfacesReplacing the Fan Tray Loosen Fan Tray Screws Pulling the Edge of the Fan Tray Slide Metal Tabs out of Slots Inserting the Metal Tabs into Slots Installing the Fan TraySliding the Fan Tray Power Connector into Receptacle 10 Tightening Fan Tray Screws Getting HelpRequired Tools Safety RecommendationsRemoving the Chassis Cover Chassis Cover Removal Figure A-1 Removing the Chassis Cover Screws Required Tools and Equipment Replacing the Boot ROMBoot ROM Replacement Locate the boot ROM on the system board. See Figure A-3 Figure A-4 Extracting Boot ROM Replacing Sdram DIMMs Sdram Dimm ReplacementFigure A-5 Removing and Replacing the Sdram Dimm Figure A-6 Inserting the New Sdram Dimm into the Socket Replacing Flash Memory SIMMsFlash Memory Simm Replacement Figure A-7 Removing the Flash Memory Simm Replacing the Chassis Cover Chassis Cover ReplacementFigure A-10 Cisco AS5350 Chassis 78-10754-03 0A Overview Replacing the Power SupplyAppendix Required Tools and Equipment Figure B-1 DC Power Supply Connections-Single Power Supply To DC source DC connector Remove the five screws on the chassis cover. See Figure B-3 Removing the Old Power Supply Power supply Mounting screw Figure B-7 Removing the Air Separator Figure B-10 Lifting the Power Supply Out of the Chassis Figure B-11 Inserting the Power Supply in the Chassis Installing the Power SupplyFigure B-12 Reconnecting the Power Cables to the Backplane Figure B-14 Replacing the Chassis Cover Input -48/-60V == 3A 150VA To DC source DC connector Appendix Replacing the Chassis Cover 78-10754-03 0A Console and Auxiliary Port Cables and Pinouts Cabling SpecificationsConsole Port Cables and Pinouts Identifying a Rollover CableDTE Auxiliary Port Cables and Pinouts Rollover Cable Modem Adapter Signal RJ-45 Pin DB-25 PinEthernet Port Pinouts Alarm Port PinoutsBits Port Pinouts Bantam Jack Port Pinouts78-10754-03 0A IN-1 NumericsIN-2 WANIN-3 IN-4 IN-5 IN-6 IN-7 IN-8
Related manuals
Manual 88 pages 30.73 Kb Manual 6 pages 32.91 Kb Manual 6 pages 49.74 Kb

AS5350 specifications

Cisco Systems has long been a leader in the networking and telecommunications field, and its AS5800 series of routers exemplify this tradition. The AS5800, along with the AS5850, AS5350, AS5400, and AS5300, provides robust solutions for service providers and enterprise-level networking applications. Each of these models has distinct features and characteristics that cater to the evolving demands of internet traffic and data processing.

The Cisco AS5800 is designed for high-capacity routing and optimized for broadband services. It supports a wide range of services, including voice, data, and video applications, making it a versatile option for service providers looking to deliver integrated solutions. It is equipped with advanced quality of service (QoS) features that ensure bandwidth is allocated effectively, holding strong even under heavy traffic conditions.

In comparison, the AS5850 offers superior processing capabilities and is typically utilized in larger-scale implementations. This model supports high-density interfaces, allowing numerous connections without compromising performance. Its architecture includes enhanced MPLS (Multiprotocol Label Switching) support, enabling more efficient traffic management and better utilization of network resources.

The AS5350 is known for its scalability and energy efficiency, ideal for voice-over-IP (VoIP) and media gateway applications. It supports various telephony features, such as protocol interworking and transcoding, making it a preferred choice for organizations focusing on digital voice technologies. The AS5300, while slightly older, continues to be a valuable asset for less demanding networks, offering reliable performance with VoIP capabilities and basic data applications.

The AS5400 bridges the gap between high-performance routing and operational efficiency. It incorporates Cisco's proprietary technologies to ensure seamless connectivity and robust failover systems. This model is highly regarded for its security features, protecting network integrity and providing peace of mind for businesses relying on sensitive data transfer.

Overall, Cisco’s AS5800 series showcases a progressive evolution of routing capabilities with enhanced features tailored for resilience, scalability, and performance. These routers not only address the technical needs of modern networks but also strategically position organizations for future growth in an increasingly digital world. Each model, with its unique attributes, continues to support the varied demands of global communication infrastructures.