Cisco Systems AS5350 manual Setting Up the Chassis, Setting the Chassis on a Desktop

Page 28

Chapter 3 Installing the Cisco AS5350

Setting Up the Chassis

Setting Up the Chassis

You can set the chassis on a desktop or install it in a rack. Use the procedure in this section that best meets the needs of your network:

•Setting the Chassis on a Desktop

•Rack-Mounting the Chassis

Warning When installing the unit, the ground connection must always be made first and disconnected last. To see translations of the warnings that appear in the publication, refer to the Regulatory Compliance and Safety Information document that accompanied this device.

Warning This unit is intended for installation in restricted access areas. A restricted access area is where access can only be gained by service personnel through the use of a special tool, lock and key, or other means of security, and is controlled by the authority responsible for the location. To see translations of the warnings that appear in the publication, refer to the Regulatory Compliance and Safety Information document that accompanied this device.

Setting the Chassis on a Desktop

The location of the chassis is extremely important for proper operation. Equipment placed too close together, inadequate ventilation, and inaccessible panels can cause malfunctions and shutdowns, and can make maintenance difficult. The following information will help you plan the location of the chassis:

•Plan for access to both front and rear panels of the chassis.

•Ensure that the room where the chassis operates has adequate ventilation. Remember that electrical equipment generates heat. Ambient air temperature may not cool equipment to acceptable operating temperatures without adequate ventilation.

Attaching the Rubber Feet

To attach the rubber feet to the chassis, follow this procedure:

Step 1 Carefully turn the chassis over so you can see the four small depressions made for attaching the rubber feet. (See Figure 3-1.) The rubber feet are included in the accessory kit that shipped with your universal gateway.

Step 2 Remove the wax paper from the bottom of each rubber foot and press the foot into the small depression on the bottom of the chassis. (See Figure 3-1.)

 

Cisco AS5350 Universal Gateway Chassis Installation Guide

3-2

78-10754-03 0A

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Cisco AS5350 Universal Gateway Chassis Installation Guide Cisco AS5350 Universal Gateway Chassis Installation Guide Preface IiiLEDs Overview B-1 78-10754-03 0A Document Organization ViiDocument Conventions ViiiDocument Conventions Document Conventions OBS! Spara Dessa Anvisningar Related Documentation XiiNew Hardware Features Obtaining DocumentationCisco.com Documentation CD-ROMObtaining Technical Assistance Ordering DocumentationDocumentation Feedback XivTechnical Assistance Center Cisco TAC WebsiteObtaining Additional Publications and Information XviOverview Chassis ComponentsDial Feature Cards DFCs Cisco AS5350 Front PanelPower Supply Chassis SpecificationsSee the Regulatory Compliance and Safety Safety Recommendations Preparing to Install the Cisco AS5350 ChassisMaintaining Safety with Electricity Preventing Electrostatic Discharge Damage Required Tools and Equipment Preparing to Connect to a NetworkEthernet Connections Console and Auxiliary Ports2T Serial Ports Alarm PortBits Port Power Supply Considerations Installing the Cisco AS5350 Setting Up the Chassis Setting the Chassis on a DesktopRack-Mounting the Chassis Attaching the Rubber FeetRequired Tools and Equipment Installing in a Rack Connecting to the Network Cisco AS5350 Ground Lug AttachmentConnecting to an Ethernet Network Connecting to a WANConnecting a 2-Port or 4-Port DFC to an RJ-45 T1 Jack Connecting an 8-Port DFC to a RJ-45 T1 Jack 10 Connecting a 2-Port or 4-Port DFC to an RJ-45 Jack Connecting to the Console and Auxiliary Ports Connecting to the Console PortConnecting a Modem to the Auxiliary Port 13 Connecting the Console TerminalConnecting a Signal Generator to the Bits Port 14 Connecting a Modem to the Auxiliary PortConnecting an Alarm to the Alarm Port To alarm device Cable ties Alarm port connectorSupplying Power Accompanied this device17 Connecting the AC Power Cord 19 DC Power Supply Connections-Single Power Supply 20 DC Power Supply Connections-Redundant Power Supply Where to Go Next 78-10754-03 0A Troubleshooting LEDsLED Monitoring Environment Cisco AS5350 Slot NumberingDisplaying Environment Status Router# show environment Replacing the Fan Tray Troubleshooting Network InterfacesRemoving the Fan Tray Loosen Fan Tray Screws Pulling the Edge of the Fan Tray Slide Metal Tabs out of Slots Installing the Fan Tray Inserting the Metal Tabs into SlotsSliding the Fan Tray Power Connector into Receptacle Getting Help 10 Tightening Fan Tray ScrewsRemoving the Chassis Cover Safety RecommendationsRequired Tools Chassis Cover Removal Figure A-1 Removing the Chassis Cover Screws Boot ROM Replacement Replacing the Boot ROMRequired Tools and Equipment Locate the boot ROM on the system board. See Figure A-3 Figure A-4 Extracting Boot ROM Sdram Dimm Replacement Replacing Sdram DIMMsFigure A-5 Removing and Replacing the Sdram Dimm Replacing Flash Memory SIMMs Figure A-6 Inserting the New Sdram Dimm into the SocketFlash Memory Simm Replacement Figure A-7 Removing the Flash Memory Simm Chassis Cover Replacement Replacing the Chassis CoverFigure A-10 Cisco AS5350 Chassis 78-10754-03 0A Replacing the Power Supply OverviewAppendix Required Tools and Equipment Figure B-1 DC Power Supply Connections-Single Power Supply To DC source DC connector Remove the five screws on the chassis cover. See Figure B-3 Removing the Old Power Supply Power supply Mounting screw Figure B-7 Removing the Air Separator Figure B-10 Lifting the Power Supply Out of the Chassis Installing the Power Supply Figure B-11 Inserting the Power Supply in the ChassisFigure B-12 Reconnecting the Power Cables to the Backplane Figure B-14 Replacing the Chassis Cover Input -48/-60V == 3A 150VA To DC source DC connector Appendix Replacing the Chassis Cover 78-10754-03 0A Cabling Specifications Console and Auxiliary Port Cables and PinoutsIdentifying a Rollover Cable Console Port Cables and PinoutsDTE Rollover Cable Modem Adapter Signal RJ-45 Pin DB-25 Pin Auxiliary Port Cables and PinoutsAlarm Port Pinouts Ethernet Port PinoutsBits Port Pinouts Bantam Jack Port Pinouts78-10754-03 0A Numerics IN-1WAN IN-2IN-3 IN-4 IN-5 IN-6 IN-7 IN-8
Related manuals
Manual 88 pages 30.73 Kb Manual 6 pages 32.91 Kb Manual 6 pages 49.74 Kb

AS5350 specifications

Cisco Systems has long been a leader in the networking and telecommunications field, and its AS5800 series of routers exemplify this tradition. The AS5800, along with the AS5850, AS5350, AS5400, and AS5300, provides robust solutions for service providers and enterprise-level networking applications. Each of these models has distinct features and characteristics that cater to the evolving demands of internet traffic and data processing.

The Cisco AS5800 is designed for high-capacity routing and optimized for broadband services. It supports a wide range of services, including voice, data, and video applications, making it a versatile option for service providers looking to deliver integrated solutions. It is equipped with advanced quality of service (QoS) features that ensure bandwidth is allocated effectively, holding strong even under heavy traffic conditions.

In comparison, the AS5850 offers superior processing capabilities and is typically utilized in larger-scale implementations. This model supports high-density interfaces, allowing numerous connections without compromising performance. Its architecture includes enhanced MPLS (Multiprotocol Label Switching) support, enabling more efficient traffic management and better utilization of network resources.

The AS5350 is known for its scalability and energy efficiency, ideal for voice-over-IP (VoIP) and media gateway applications. It supports various telephony features, such as protocol interworking and transcoding, making it a preferred choice for organizations focusing on digital voice technologies. The AS5300, while slightly older, continues to be a valuable asset for less demanding networks, offering reliable performance with VoIP capabilities and basic data applications.

The AS5400 bridges the gap between high-performance routing and operational efficiency. It incorporates Cisco's proprietary technologies to ensure seamless connectivity and robust failover systems. This model is highly regarded for its security features, protecting network integrity and providing peace of mind for businesses relying on sensitive data transfer.

Overall, Cisco’s AS5800 series showcases a progressive evolution of routing capabilities with enhanced features tailored for resilience, scalability, and performance. These routers not only address the technical needs of modern networks but also strategically position organizations for future growth in an increasingly digital world. Each model, with its unique attributes, continues to support the varied demands of global communication infrastructures.
Top Page Image Contents