Cisco Systems AS5350 manual Required Tools and Equipment, Flash Memory Simm Replacement

Page 68

Appendix

Replacing Flash Memory SIMMs

•The third Flash memory socket holds a SIMM for the boot helper image (rxboot) software. The SIMM can be 8 or 16 MB.

–For boot memory, the total capacity is 16 MB (one, 16 MB SIMM).

The Flash memory SIMMs must be purchased from Cisco. For ordering information, refer to the “Obtaining Technical Assistance” section on page xiv.

Required Tools and Equipment

You need the following tools and equipment:

•ESD-preventive wrist strap

•The appropriate Flash memory SIMM(s) for your universal gateway

Flash Memory SIMM Replacement

To replace the 5V Flash memory SIMMs, follow this procedure:

Step 1 Turn the power switch on the universal gateway off and disconnect site power.

Step 2 Remove all interface cables from the rear panel of the universal gateway.

Step 3 Attach an ESD-preventive wrist strap.

Step 4 Remove the chassis cover. (See the previous procedure in the “Removing the Chassis Cover” section on page A1.)

Step 5 Place the chassis so that the system board is oriented as shown in Figure A-3,with the Flash memory SIMMs toward you.

Step 6 Remove the existing Flash memory SIMM by pulling outward on the socket latches and then lifting the SIMM out of the socket (see Figure A-7).

Caution To prevent damage, do not press on the center of the SIMMs. Handle each SIMM carefully.

Step 7 Repeat these steps for all the Flash memory SIMMs that you need to replace.

 

Cisco AS5350 Universal Gateway Chassis Installation Guide

-10

78-10754-03 0A

Page 67 Page 69
Image 68
Page 67 Page 69
Contents Cisco AS5350 Universal Gateway Chassis Installation Guide Cisco AS5350 Universal Gateway Chassis Installation Guide Preface IiiLEDs Overview B-1 78-10754-03 0A Document Organization ViiDocument Conventions ViiiDocument Conventions Document Conventions OBS! Spara Dessa Anvisningar Related Documentation XiiNew Hardware Features Obtaining DocumentationCisco.com Documentation CD-ROMObtaining Technical Assistance Ordering DocumentationDocumentation Feedback XivTechnical Assistance Center Cisco TAC WebsiteObtaining Additional Publications and Information XviOverview Chassis ComponentsDial Feature Cards DFCs Cisco AS5350 Front PanelPower Supply Chassis SpecificationsSee the Regulatory Compliance and Safety Maintaining Safety with Electricity Preparing to Install the Cisco AS5350 ChassisSafety Recommendations Preventing Electrostatic Discharge Damage Required Tools and Equipment Preparing to Connect to a NetworkEthernet Connections Console and Auxiliary PortsBits Port Alarm Port2T Serial Ports Power Supply Considerations Installing the Cisco AS5350 Setting Up the Chassis Setting the Chassis on a DesktopRack-Mounting the Chassis Attaching the Rubber FeetRequired Tools and Equipment Installing in a Rack Connecting to the Network Cisco AS5350 Ground Lug AttachmentConnecting to an Ethernet Network Connecting to a WANConnecting a 2-Port or 4-Port DFC to an RJ-45 T1 Jack Connecting an 8-Port DFC to a RJ-45 T1 Jack 10 Connecting a 2-Port or 4-Port DFC to an RJ-45 Jack Connecting to the Console and Auxiliary Ports Connecting to the Console PortConnecting a Modem to the Auxiliary Port 13 Connecting the Console TerminalConnecting a Signal Generator to the Bits Port 14 Connecting a Modem to the Auxiliary PortConnecting an Alarm to the Alarm Port To alarm device Cable ties Alarm port connectorSupplying Power Accompanied this device17 Connecting the AC Power Cord 19 DC Power Supply Connections-Single Power Supply 20 DC Power Supply Connections-Redundant Power Supply Where to Go Next 78-10754-03 0A Troubleshooting LEDsLED Monitoring Environment Cisco AS5350 Slot NumberingDisplaying Environment Status Router# show environment Removing the Fan Tray Troubleshooting Network InterfacesReplacing the Fan Tray Loosen Fan Tray Screws Pulling the Edge of the Fan Tray Slide Metal Tabs out of Slots Installing the Fan Tray Inserting the Metal Tabs into SlotsSliding the Fan Tray Power Connector into Receptacle Getting Help 10 Tightening Fan Tray ScrewsRequired Tools Safety RecommendationsRemoving the Chassis Cover Chassis Cover Removal Figure A-1 Removing the Chassis Cover Screws Required Tools and Equipment Replacing the Boot ROMBoot ROM Replacement Locate the boot ROM on the system board. See Figure A-3 Figure A-4 Extracting Boot ROM Sdram Dimm Replacement Replacing Sdram DIMMsFigure A-5 Removing and Replacing the Sdram Dimm Replacing Flash Memory SIMMs Figure A-6 Inserting the New Sdram Dimm into the SocketFlash Memory Simm Replacement Figure A-7 Removing the Flash Memory Simm Chassis Cover Replacement Replacing the Chassis CoverFigure A-10 Cisco AS5350 Chassis 78-10754-03 0A Replacing the Power Supply OverviewAppendix Required Tools and Equipment Figure B-1 DC Power Supply Connections-Single Power Supply To DC source DC connector Remove the five screws on the chassis cover. See Figure B-3 Removing the Old Power Supply Power supply Mounting screw Figure B-7 Removing the Air Separator Figure B-10 Lifting the Power Supply Out of the Chassis Installing the Power Supply Figure B-11 Inserting the Power Supply in the ChassisFigure B-12 Reconnecting the Power Cables to the Backplane Figure B-14 Replacing the Chassis Cover Input -48/-60V == 3A 150VA To DC source DC connector Appendix Replacing the Chassis Cover 78-10754-03 0A Cabling Specifications Console and Auxiliary Port Cables and PinoutsIdentifying a Rollover Cable Console Port Cables and PinoutsDTE Rollover Cable Modem Adapter Signal RJ-45 Pin DB-25 Pin Auxiliary Port Cables and PinoutsAlarm Port Pinouts Ethernet Port PinoutsBits Port Pinouts Bantam Jack Port Pinouts78-10754-03 0A Numerics IN-1WAN IN-2IN-3 IN-4 IN-5 IN-6 IN-7 IN-8
Related manuals
Manual 88 pages 30.73 Kb Manual 6 pages 32.91 Kb Manual 6 pages 49.74 Kb

AS5350 specifications

Cisco Systems has long been a leader in the networking and telecommunications field, and its AS5800 series of routers exemplify this tradition. The AS5800, along with the AS5850, AS5350, AS5400, and AS5300, provides robust solutions for service providers and enterprise-level networking applications. Each of these models has distinct features and characteristics that cater to the evolving demands of internet traffic and data processing.

The Cisco AS5800 is designed for high-capacity routing and optimized for broadband services. It supports a wide range of services, including voice, data, and video applications, making it a versatile option for service providers looking to deliver integrated solutions. It is equipped with advanced quality of service (QoS) features that ensure bandwidth is allocated effectively, holding strong even under heavy traffic conditions.

In comparison, the AS5850 offers superior processing capabilities and is typically utilized in larger-scale implementations. This model supports high-density interfaces, allowing numerous connections without compromising performance. Its architecture includes enhanced MPLS (Multiprotocol Label Switching) support, enabling more efficient traffic management and better utilization of network resources.

The AS5350 is known for its scalability and energy efficiency, ideal for voice-over-IP (VoIP) and media gateway applications. It supports various telephony features, such as protocol interworking and transcoding, making it a preferred choice for organizations focusing on digital voice technologies. The AS5300, while slightly older, continues to be a valuable asset for less demanding networks, offering reliable performance with VoIP capabilities and basic data applications.

The AS5400 bridges the gap between high-performance routing and operational efficiency. It incorporates Cisco's proprietary technologies to ensure seamless connectivity and robust failover systems. This model is highly regarded for its security features, protecting network integrity and providing peace of mind for businesses relying on sensitive data transfer.

Overall, Cisco’s AS5800 series showcases a progressive evolution of routing capabilities with enhanced features tailored for resilience, scalability, and performance. These routers not only address the technical needs of modern networks but also strategically position organizations for future growth in an increasingly digital world. Each model, with its unique attributes, continues to support the varied demands of global communication infrastructures.
Top Page Image Contents