D-Link DFL-200 manual WAN Interface Settings Using Pptp

Page 18

WAN Interface Settings – Using PPTP

PPTP over Ethernet connections are used in some DSL and cable modem networks.

You need your account details, and possibly also IP configuration parameters of the actual physical interface that the PPTP tunnel runs over. Your ISP should supply this information.

•Username – The login or username supplied to you by your ISP.

•Password – The password supplied to you by your ISP.

•PPTP Server IP – The IP of the PPTP server that the DFL-200 should connect to.

Before PPTP can be used to connect to you ISP the physical (WAN) interface parameters need to be supplied, it’s possible to use either DHCP or Static IP, this depends on the type of ISP used and this information should be supplied by them.

If using static IP, this information need to be filled in.

•IP Address – The IP address of the WAN interface. This IP is used to connect to the PPTP server.

•Subnet Mask – Size of the external network.

•Gateway IP – Specifies the IP address of the default gateway used to reach for the Internet.

18

Image 18

Contents Link DFL-200 Contents VPN Servers 111 122 125Introduction Features and BenefitsAccess Control supported Introduction to FirewallsIntroduction to Local Area Networking LEDs Physical ConnectionsPackage Contents System RequirementsResetting the DFL-200 Managing D-Link DFL-200Administration Settings Administrative AccessAdd ping access to an interface Add Admin access to an interfaceAdd Read-only access to an interface Enable Snmp access to an interfaceSystem InterfacesChange IP of the LAN or DMZ interface WAN Interface Settings Using Static IP WAN Interface Settings Using DhcpIP Address The IP address of the WAN interface. This is WAN Interface Settings Using PPPoE PasswordWAN Interface Settings Using Pptp WAN Interface Settings Using BigPond MTU ConfigurationPassword The password supplied to you by your ISP Routing Add a new Static Route Remove a Static RouteGo to System and Routing Logging Enable Logging Enable Audit LoggingEnable E-mail alerting for ISD/IDP events Page Time Changing time zone Using NTP to sync timeSetting time and date manually Checking the Set the system time boxPolicy modes FirewallPolicy Action TypesService Filter Source and Destination FilterSchedule Intrusion Detection / Prevention Add a new policyEnable the Intrusion Detection / Prevention checkbox Configure Intrusion DetectionEnable the Delete policy checkbox Change order of policyConfigure Intrusion Prevention Port mapping / Virtual Servers Add a new mappingEnable the Delete mapping checkbox Delete mappingUsers DFL-200 Radius SupportEnable User Authentication via Http / Https Enable Radius SupportChange User Password Enable the Change password checkboxAdd User Enable the Delete user checkbox Delete UserSchedules Add new recurring scheduleServices Adding TCP, UDP or TCP/UDP ServiceGrouping Services Adding IP ProtocolProtocol-independent settings VPN Introduction to IPSecIntroduction to Pptp Introduction to L2TPPoint-to-Point Protocol Authentication Protocols MPPE, Microsoft Point-To-Point EncryptionAuthentication protocol L2TP/PPTP ClientsAuthentication Protocol Introduction chapter L2TP/PPTP ServersMppe encryption VPN between two networks Creating a LAN-to-LAN IPSec VPN TunnelVPN between client and an internal network Creating a Roaming Users IPSec VPN TunnelAdding a L2TP/PPTP VPN Client Adding a L2TP/PPTP VPN ServerVPN Advanced Settings Proposal Lists IKE Proposal ListIPSec Proposal List Local identities CertificatesTrusting Certificates Certificates of remote peersIdentities Content Filtering Active content handlingEdit the URL Global Whitelist Edit the URL Global Blacklist Active content handling Dhcp Server Settings ServersDisable Dhcp Server/Relayer Enable Dhcp ServerEnable Dhcp Relay Enable by checking the Use built-in Dhcp Server boxDNS Relayer Settings Enable DNS RelayerEnable by checking the Enable DNS Relayer box Disable DNS Relayer Tools PingAdd Dynamic DNS Settings Dynamic DNSPing Example Backup Exporting the DFL-200’s ConfigurationRestoring the DFL-200’s Configuration Restart/Reset Restarting the DFL-200Restoring system settings to factory defaults Page Upgrade Upgrade FirmwareUpgrade IDS Signature-database Status SystemCPU Load Interfaces VPN Connections Click Connections below it. a window willDhcp Server Logging Drop events How to read the logsUsage events Conn eventsOpen Example Close ExampleStep by step guides LAN-to-LAN VPN using IPsec LAN IP 192.168.4.1, Subnet maskEnable Automatically add a route for the remote network Remote Net 192.168.1.0/24LAN IP 192.168.1.1, Subnet mask Local net 192.168.1.0/24Remote Net 192.168.4.0/24 LAN-to-LAN VPN using Pptp Username BranchOffice Click Global policy parameters Settings for Main office Page Select Local database Under Users in local database click Add newPage LAN-to-LAN VPN using L2TP Username BranchOffice Check Use IPsec encryption Setup interfaces, System-Interfaces WAN IP193.0.2.20 Page Select Local database Under Users in local database click Add new More secure LAN-to-LAN VPN solution Page Page Settings for Main office Settings for the Windows XP client Windows XP client and Pptp serverSelect Connect to the network at my workplace and click Next Select Virtual Private Network connection and click Next Name the connection MainOffice and click Next 104 Select Do not dial the initial connection and click Next Page Click Properties Page Name the new user HomeUser Enter password Retype password Page Windows XP client and L2TP server 112 Settings for Main office Page Content filtering Firewall-Services Select HTTP/HTML Content Filtering in the ALG dropdownPage Page Intrusion detection and prevention Page Check Enable E-mail alerting for IDS/IDP events Appendixes Appendix a Icmp Types and CodesPage Appendix B Common IP Protocol Numbers ESPLimited Warranty What Is Not Covered Wichtige Sicherheitshinweise Advertencia de Marca de la CE CE Mark WarningWarnung AttenzioneVcci Warning Offices Singapore D-LINK International 132

Related manuals

Manual 14 pages 8.62 Kb

Manual 12 pages 24 Kb