D-Link DFL-200 manual LEDs, Physical Connections

Page 9

LEDs

Power: A solid light indicates a proper connection to the power supply.

Status: System status indicators, The LED has a solid green, the device is working normally. If the LED is light off the unit is defective.

WAN, DMZ & LAN ports: Ethernet port indicators, Green. The LED flickers when the ports are sending or receiving data.

Physical Connections

Console: Serial access to the firewall software, 9600, 8bit, None Parity, 1Stop bit.

Internal Ports (LAN): Use these ports to connect the internal computers f the office.

DMZ Port: Use this port to connect to the company’s server(s), which needs direct connection to the Internet (FTP, SNMP, HTTP and DNS).

External Port (WAN): Use this port to connect to the external router, DSL modem, or Cable modem.

Reset: Reset the DFL-200 to the original default settings.

DC Power: connect one end of the power supply to this port, the other end to the electrical wall outlet.

Image 9

Contents Link DFL-200 Contents VPN Servers 111 125 122Access Control supported Features and BenefitsIntroduction Introduction to FirewallsIntroduction to Local Area Networking Physical Connections LEDsSystem Requirements Package ContentsManaging D-Link DFL-200 Resetting the DFL-200Administrative Access Administration SettingsAdd Admin access to an interface Add ping access to an interfaceEnable Snmp access to an interface Add Read-only access to an interfaceSystem InterfacesChange IP of the LAN or DMZ interface WAN Interface Settings Using Static IP WAN Interface Settings Using DhcpIP Address The IP address of the WAN interface. This is Password WAN Interface Settings Using PPPoEWAN Interface Settings Using Pptp WAN Interface Settings Using BigPond MTU ConfigurationPassword The password supplied to you by your ISP Routing Add a new Static Route Remove a Static RouteGo to System and Routing Logging Enable Logging Enable Audit LoggingEnable E-mail alerting for ISD/IDP events Page Time Setting time and date manually Using NTP to sync timeChanging time zone Checking the Set the system time boxPolicy FirewallPolicy modes Action TypesService Filter Source and Destination FilterSchedule Add a new policy Intrusion Detection / PreventionEnable the Delete policy checkbox Configure Intrusion DetectionEnable the Intrusion Detection / Prevention checkbox Change order of policyConfigure Intrusion Prevention Add a new mapping Port mapping / Virtual ServersDelete mapping Enable the Delete mapping checkboxDFL-200 Radius Support UsersEnable Radius Support Enable User Authentication via Http / HttpsChange User Password Enable the Change password checkboxAdd User Delete User Enable the Delete user checkboxAdd new recurring schedule SchedulesAdding TCP, UDP or TCP/UDP Service ServicesAdding IP Protocol Grouping ServicesProtocol-independent settings Introduction to IPSec VPNIntroduction to Pptp Introduction to L2TPPoint-to-Point Protocol MPPE, Microsoft Point-To-Point Encryption Authentication ProtocolsL2TP/PPTP Clients Authentication protocolL2TP/PPTP Servers Authentication Protocol Introduction chapterMppe encryption Creating a LAN-to-LAN IPSec VPN Tunnel VPN between two networksCreating a Roaming Users IPSec VPN Tunnel VPN between client and an internal networkAdding a L2TP/PPTP VPN Server Adding a L2TP/PPTP VPN ClientVPN Advanced Settings Proposal Lists IKE Proposal ListIPSec Proposal List Trusting Certificates CertificatesLocal identities Certificates of remote peersIdentities Active content handling Content FilteringEdit the URL Global Whitelist Edit the URL Global Blacklist Active content handling Servers Dhcp Server SettingsEnable Dhcp Relay Enable Dhcp ServerDisable Dhcp Server/Relayer Enable by checking the Use built-in Dhcp Server boxDNS Relayer Settings Enable DNS RelayerEnable by checking the Enable DNS Relayer box Disable DNS Relayer Ping ToolsAdd Dynamic DNS Settings Dynamic DNSPing Example Backup Exporting the DFL-200’s ConfigurationRestoring the DFL-200’s Configuration Restarting the DFL-200 Restart/ResetRestoring system settings to factory defaults Page Upgrade Upgrade FirmwareUpgrade IDS Signature-database Status SystemCPU Load Interfaces VPN Click Connections below it. a window will ConnectionsDhcp Server Logging Usage events How to read the logsDrop events Conn eventsClose Example Open ExampleStep by step guides LAN IP 192.168.4.1, Subnet mask LAN-to-LAN VPN using IPsecRemote Net 192.168.1.0/24 Enable Automatically add a route for the remote networkLocal net 192.168.1.0/24 LAN IP 192.168.1.1, Subnet maskRemote Net 192.168.4.0/24 LAN-to-LAN VPN using Pptp Username BranchOffice Click Global policy parameters Settings for Main office Page Under Users in local database click Add new Select Local databasePage LAN-to-LAN VPN using L2TP Username BranchOffice Check Use IPsec encryption Setup interfaces, System-Interfaces WAN IP193.0.2.20 Page Select Local database Under Users in local database click Add new More secure LAN-to-LAN VPN solution Page Page Settings for Main office Windows XP client and Pptp server Settings for the Windows XP clientSelect Connect to the network at my workplace and click Next Select Virtual Private Network connection and click Next Name the connection MainOffice and click Next 104 Select Do not dial the initial connection and click Next Page Click Properties Page Name the new user HomeUser Enter password Retype password Page Windows XP client and L2TP server 112 Settings for Main office Page Content filtering Select HTTP/HTML Content Filtering in the ALG dropdown Firewall-ServicesPage Page Intrusion detection and prevention Page Check Enable E-mail alerting for IDS/IDP events Appendix a Icmp Types and Codes AppendixesPage ESP Appendix B Common IP Protocol NumbersLimited Warranty What Is Not Covered Wichtige Sicherheitshinweise Warnung CE Mark WarningAdvertencia de Marca de la CE AttenzioneVcci Warning Offices Singapore D-LINK International 132

Related manuals

Manual 14 pages 8.62 Kb

Manual 12 pages 24 Kb