Fisher-Price 79667 instruction sheet Attached

Page 5

Assembly

Motorized Frame

L

R

Elbow Foot

Tube

 

Button

 

 

5

 

Red Dot

 

Hole

 

 

Locate the R and L on the underside of each elbow foot. The R indicates the right leg. The L indicates the left leg.

While pressing the upper button on the right leg, fit it into the tube in the motorized frame. Make sure the upper button on the right leg “snaps” into the hole in the tube.

Repeat this procedure to assemble the left leg to the motorized frame.

When the legs are assembled correctly to the tubes in the motorized frame, you should not see the red dots.

Button

Button

Ruffle

Seat

Slot

Crotch Belt

7

Position the seat upright.

Place the pad onto the seat with the ruffle toward the top of the seat.

Fold the bottom of the pad up. Insert the crotch belt through the slot in the pad. Make sure the crotch belt is not twisted.

Hole

Hole

 

 

 

Elastic

 

 

Storage Pouch

Loops

 

 

 

 

 

Pockets

 

 

Feet

Feet

Peg

 

 

8

6

 

Elastic

 

L

R

Loops

• Stand the assembly upright.

 

 

• Fold the top of the pad down.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Insert the two elastic loops on the pad

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Pull the legs out so that the buttons “snap” into the holes in

 

 

through the holes in the seat bottom

 

 

 

Bottom

View

 

the motorized frame. If the buttons do not “snap” into the

 

• While holding the elastic loops in place, turn the seat

holes, you probably have not assembled the storage pouch

 

 

 

face down.

 

 

 

 

 

 

 

correctly. Please refer back to assembly steps 3 and 4.

 

 

 

 

 

 

 

 

 

 

• Hook the elastic loop on the left side onto the peg on the

• When standing behind the product, all four feet should be

 

 

 

right side.

 

 

 

 

 

 

 

flat upon the floor. And, check for an L marking on the left

 

 

 

 

 

 

 

 

 

 

• Hook the elastic loop on the right side onto the peg on the

foot and an R marking on the right foot.

 

 

 

left side.

 

 

 

 

 

 

 

• If the feet are not flat upon the floor, or the left and right feet

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Hint:

 

The

elastic

 

 

loops

 

should

 

 

cross

 

over

 

each

 

other

 

when

 

 

have been reversed, remove both lower legs from the upper

 

 

 

 

 

 

 

 

 

 

 

 

 

 

legs. Replace them onto the opposite upper leg.

5

 

attached

correctly

 

to

the

pegs.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Image 5
Contents Model Number Aquarium Cradle SwingConsumer Information One 1 Year Limited WarrantyParts Shown Actual Size AssemblyAttached Insert the tray tabs into the slots in each side of the seat Make sure the rounded side of the lock nut faces out 5V x LR20 SafetyTo loosen the waist belts Swing, Waterglobe and Mobile UseTo tighten the waist belts Adjust Swing Motions Using the Tray To select sounds or music, slide switch to To select waterglobe/mobile, slide switch toSwing Waterglobe, Mobile, Music and SoundsCare Problems and Solutions
Related manuals
Manual 2 pages 43.1 Kb