Fiesta Products 7305 manual Installing Transmitter Batteries, Setting UP the Antenna

Page 10

If the power indicator doesn’t light red, check the polarity of the batteries. Check rechargeable batteries for a full charge.

Spray a little window cleaner on the antenna wire to make it easier to push through the antenna tube.

If there are any kinks in the black antenna wire, it will be more difficult to push through the antenna tube. Pull the wire straight by sandwiching it between your thumb and index finger and running your fingers along the length of the wire (with medium pressure).

Don’t shorten the length of the antenna wire. Its length is tuned to the frequency band; cutting it could severely shorten the radio system’s range.

THE TRAXXAS TQ RADIO SYSTEM

INSTALLING TRANSMITTER BATTERIES

Your TQ transmitter uses 8 AA batteries (see sidebar, page 11).

The battery compartment is located in the base of the transmitter.

1.Remove the battery compartment door by pressing the tab and lifting the door up.

2.Install the batteries in the correct orientation as indicated in the battery compartment.

3.Reinstall the battery door and snap it closed.

4.Turn on the transmitter and check the power indicator for a solid red light.

If the power indicator light flashes, then the transmitter batteries are weak, discharged or possibly installed incorrectly. Replace with new or freshly charged batteries. The power indicator light does not indicate the charge level of the battery pack installed in the model.

SETTING UP THE ANTENNA

1.Locate the black antenna wire that exits the receiver box.

2.Pull the wire straight with your fingers and then insert the end of the wire into one end of the antenna tube (the antenna tube can be found in the documents bag). Push the wire all the way through the antenna tube. The wire is longer than the tube. Do not cut or shorten the antenna wire.

3.Insert the base of the tube into the antenna mount. Take care not to crimp the antenna wire.

4.Using the supplied 1.5mm “L” wrench, thread the 1.5mm set screw into the opening next to the antenna. Tighten the set screw until it is flush with the top of the opening.

5.Fold the top of the antenna wire over the top of the antenna tube. Slide the antenna tip onto the top of the antenna tube. Do not cut or shorten the antenna wire.

6.The receiver antenna installation is complete. Always fully extend the transmitter’s telescoping antenna when running your model. Make a habit of holding the transmitter so the antenna points straight up.

Antenna

Tip

Antenna

Tube

1.5mm

Wrench

Set

Screw

Antenna

Mount

See page 18 for more information about the receiver box and maintaining a watertight seal.

2,3,4

CHARGING THE BATTERY PACK

Your model includes a ‘wall charger’ that will charge the supplied battery in approximately six hours. Plug the charger into the wall. Connect the included battery pack to the charger output cord. After six hours, unplug the battery from the charger, and unplug the charger from the wall, when charging is complete. Never leave a battery unattended while charging.

10 • TRAXXAS

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Model Traxxas Support IntroductionQuick Start Support Before YOU ProceedTraxxas Important Points to Remember Safety PrecautionsBatteries and Battery Charging Speed ControlSupplied Tools and Equipment Required Equipment TOOLS, Supplies and Required EquipmentDecorating Your Model Applying the DecalsAnatomy of the Model Battery Door Release Tab Compartment Vent Steering ServoToe Link Push Rod Rear Body Mount Rocker Rear Half Shaft Quick Start Getting UP to Speed TQ Transmitter Radio System Wiring DiagramTraxxas TQ Radio System XL-2.5 Electronic Speed ControlRadio System Terminology Channel radio system The TQ radio system, consistingCharging the Battery Pack Installing Transmitter BatteriesSetting UP the Antenna Locate the black antenna wire that exits the receiver boxBattery Installation Installing Battery PackTraxxas High Current Connector Using an Additional Battery Pack for Increased Run TimeTQ Radio System Adjustments TQ Radio System ControlsTQ Radio System Setup RANGE-TESTING the TQ Radio SystemTransmitter should be adjusted as follows Adjusting the Electronic Speed ControlTransmitter Adjustments for the electronic speed control ESC OperationESC Profile Selection Selecting Sport Mode Profile #1Selecting Race Mode Profile #2 ESC Profile DescriptionDriving Your Model Running in WET ConditionsConfirm that your batteries can be used in wet conditions Motor PrecautionsBefore Running Your Vehicle in Wet Conditions After Running Your Vehicle in Wet ConditionsAntenna wire B Apply a small bead of silicone grease Removing and Installing Radio GearReceiver Installation Removing the ReceiverVehicle’s ride height Tuning AdjustmentsSuspension Tuning Shock OilAdjusting Toe-In Static Camber AdjustmentStatic Camber Base Factory Settings Negative camberTransmission Tuning Wheels and TiresAdjusting Gear Mesh Pinion Gear Installation InstructionsMotor Installation Motor and GearingInspect the vehicle for obvious damage or wear. Look for Other periodic maintenanceMaintaining Your Model StorageModel

7305 specifications

Fiesta Products 7305 is a versatile and innovative outdoor product designed to enhance your outdoor experience. Known for its quality and functionality, this product caters to various needs, making it a popular choice among outdoor enthusiasts.

One of the main features of the Fiesta Products 7305 is its durable construction. It is made from high-grade materials that ensure longevity, even when exposed to harsh weather conditions. The robust design allows it to withstand the rigors of outdoor use, making it an ideal investment for those who enjoy spending time in their gardens, patios, or at camping sites.

The Fiesta Products 7305 incorporates advanced technologies that enhance its usability. One such technology is its easy-to-use assembly system. The product is designed for quick setup and takedown, allowing users to focus on enjoying their outdoor activities rather than struggling with complicated instructions. This feature makes it perfect for spontaneous outings, whether it's a family picnic or an outdoor party.

Additionally, the Fiesta Products 7305 is designed with portability in mind. Its lightweight nature makes it easy to transport, so you can take it wherever your outdoor adventures lead. This aspect is especially appealing for campers and hikers who appreciate convenience without sacrificing quality.

Another significant characteristic is its multifunctionality. The Fiesta Products 7305 can serve various purposes, such as a table for meals, a stand for beverages, or even as a base for outdoor games. This adaptability allows it to cater to different activities, ensuring that it fulfills multiple roles during your outdoor gatherings.

The product also features enhanced stability, thanks to its design and structural integrity. This makes it reliable for use on various surfaces, from grassy lawns to sandy beaches. Users can enjoy peace of mind knowing that their Fiesta Products 7305 will remain steady throughout their activities.

In summary, the Fiesta Products 7305 is a highly durable, portable, and multifunctional outdoor product that incorporates user-friendly features and advanced technology. Its robustness and versatility make it an excellent choice for anyone looking to elevate their outdoor experiences, whether at home or on the go. Emphasizing quality and practicality, the Fiesta Products 7305 stands out as an essential addition to any outdoor enthusiast's collection.
Top Page Image Contents