Cisco Systems 12.4 manual Information About Mpls LDP Graceful Restart

Page 72

How MPLS LDP Graceful Restart Works

Information About MPLS LDP Graceful Restart

•MPLS LDP GR is supported in strict helper mode.

•Tag Distribution Protocol (TDP) sessions are not supported. Only LDP sessions are supported.

•MPLS LDP GR cannot be configured on label-controlled ATM (LC-ATM) interfaces.

•MPLS LDP SSO/NSF is supported in IOS Release 12.2(25)S. It is not supported in this release.

Information About MPLS LDP Graceful Restart

•How MPLS LDP Graceful Restart Works, page 66

•How a Route Processor Advertises That It Supports MPLS LDP Graceful Restart, page 67

•What Happens If a Route Processor Does Not Have LDP Graceful Restart, page 67

How MPLS LDP Graceful Restart Works

MPLS LDP GR works in strict helper mode, which means it helps a neighboring route processor that has MPLS LDP SSO/NSF to recover from disruption in service without losing its MPLS forwarding state. The disruption in service could be the result of a TCP or UDP event or the stateful switchover of a route processor. When the neighboring router establishes a new session, the LDP bindings and MPLS forwarding states are recovered.

In the topology shown in the figure below, the following elements have been configured:

•LDP sessions are established between Router 1 and Router 2, as well as between Router 2 and Router 3.

•Router 2 has been configured with MPLS LDP SSO/NSF. Routers 1 and 3 have been configured with

MPLS LDP GR.

•A label switched path (LSP) has been established between Router 1 and Router 3.

Figure 4

Example of a Network Using LDP Graceful Restart

The following process shows how Routers 1 and 3, which have been configured with LDP GR help Router 2, which has been configured with LDP SSO/NSF recover from a disruption in service:

1Router 1 notices an interruption in service with Router 2. (Router 3 also performs the same actions in this process.)

2Router 1 marks all the label bindings from Router 2 as stale, but it continues to use the bindings for MPLS forwarding.

Router 1 reestablishes an LDP session with Router 2, but keeps its stale label bindings. If you issue a show mpls ldp neighbor command with the graceful-restartkeyword, the command output displays the recovering LDP sessions.

1Both routers readvertise their label binding information. If Router 1 relearns a label from Router 2 after the session has been established, the stale flags are removed. The show mpls forwarding- tablecommand displays the information in the MPLS forwarding table, including the local label, outgoing label or VC, prefix, label-switched bytes, outgoing interface, and next hop.

You can set various graceful restart timers. See the following commands for more information:

MPLS LDP Configuration Guide, Cisco IOS Release 12.4

66

Page 71 Page 73
Image 72
Page 71 Page 73
Contents Mpls LDP Configuration Guide, Cisco IOS Release Page N T E N T S Mpls LDP Inbound Label Binding Filtering Mpls LDP Graceful Restart Contents Mpls LDP Configuration Guide, Cisco IOS Release Finding Feature Information Prerequisites for Mpls LDPInformation About Mpls LDP Introduction to Mpls LDP Mpls LDP Functional OverviewLDP and TDP Support Train and ReleaseIntroduction to LDP Sessions Train and Release LDP/TDP SupportNondirectly Connected Mpls LDP Sessions How to Configure Mpls LDP Enabling Directly Connected LDP Sessions,Step Command or Action Purpose Enabling Directly Connected LDP SessionsExample Command or Action Purpose StepStep Command or Action Establishing Nondirectly Connected Mpls LDP SessionsExamples Mpls label protocol ldp tdp both Interface tunnelnumber Tunnel destination ip-address Saving Configurations Mpls Tag Switching Commands Specifying the LDP Router ID Routerconfig# mpls ldp Router-id pos2/0/0 Preserving QoS Settings with Mpls LDP Explicit Null Following example displays the LDP router IDInterface type number Command or Action Purpose Local Outgoing Prefix Protecting Data Between LDP Peers with MD5 Authentication Summary Steps Mpls ldp neighbor vrf vpn-nameip Mpls LDP Configuration Examples Configuring Directly Connected Mpls LDP Sessions ExampleRouter 1 Configuration Router 2 ConfigurationRouter 3 Configuration Establishing Nondirectly Connected Mpls LDP Sessions Example Router 4 Configuration Router 5 ConfigurationRouter 6 Configuration Additional References Feature Information for Mpls Label Distribution Protocol Technical Assistance Description LinkReleases Feature Information Router-idFeature Name Releases Feature Name Releases Feature Information Page Restrictions for Mpls LDP Session Protection Information About Mpls LDP Session ProtectionMpls LDP Session Protection Customizations How to Configure Mpls LDP Session Protection Enabling Mpls LDP Session ProtectionRouterconfig-if#mpls label protocol ldp Verifying Mpls LDP Session Protection Troubleshooting Tips Router# show mpls ldp neighbor detailIp classless Redundancy Full-duplex Interface Ethernet5/0/2 MIBs MIBs Link RFCs TitleCommand Reference Mpls LDP Inbound Label Binding Filtering RestrictionsHow to Configure Mpls LDP Inbound Label Binding Filtering Configuring Mpls LDP Inbound Label Binding FilteringIp access-list standard access-list-number Verifying that Mpls LDP Inbound Label Bindings are Filtered Router# show mpls ldp neighbor 10.12.12.12 detailAccess-list-number Access-list-name LDP Specification, draft-ietf-mpls-ldp-08.txt Technical Assistance Description Link Releases Feature Information GlossaryMpls LDP Inbound Label Binding Filtering Page Mpls LDP Autoconfiguration Restrictions for Mpls LDP AutoconfigurationInformation About Mpls LDP Autoconfiguration How to Configure Mpls LDP AutoconfigurationMpls LDP Autoconfiguration on Ospf and IS-IS Interfaces Configuring Mpls LDP Autoconfiguration with Ospf InterfacesGlobally enables hop-by-hop forwarding Router ospf process-id Verifying Mpls LDP Autoconfiguration with Ospf Router# show mpls interfaces Serial 2/0 detail Configuring Mpls LDP Autoconfiguration with IS-IS Interfaces Command or Action Purpose StepEnables IS-IS for IP on the interface Enables the LDP for interfaces that belong to an IS-IS Verifying Mpls LDP Autoconfiguration with IS-IS Router# show isis mpls ldpMpls LDP Autoconfiguration with Ospf Example Troubleshooting TipsMpls LDP Autoconfiguration with IS-IS Examples Command ReferenceFeature Information for Mpls LDP Autoconfiguration Feature Information for Mpls LDP Autoconfiguration Mpls LDP Graceful Restart Information About Mpls LDP Graceful Restart How Mpls LDP Graceful Restart WorksHow to Configure Mpls LDP Graceful Restart Configuring Mpls LDP Graceful RestartMpls ip Mpls label protocol ldptdpboth Configuration Example for Mpls LDP Graceful Restart Verifying the ConfigurationRouter 1 configured with LDP GR Router 2 configured with LDP SSO/NSFRouter 3 configured with LDP SSO/NSF Mpls label protocol ldp mpls traffic-eng tunnels mpls ipMpls Label Distribution Protocol Feature Information for Mpls LDP Graceful Restart Feature Information for Mpls LDP Graceful Restart

12.4 specifications

Cisco Systems has consistently been at the forefront of networking technology, and one of its notable software releases is IOS version 12.4. This version introduced significant enhancements and features that continue to influence networking practices. IOS 12.4 was specifically designed to accommodate the growing demands of network reliability, scalability, and advanced functionalities.

One of the primary characteristics of IOS 12.4 is its enhanced security features. The version integrates advanced security protocols, including improvements in IPsec, which allows for secure communication across potentially insecure networks. Additionally, it supports firewall technologies and access control lists (ACLs), ensuring that organizations can implement stringent security measures tailored to their traffic requirements.

Another defining feature of IOS 12.4 is its support for IPv6. As the internet continued to grow, the need for expanded address space became critical. With IOS 12.4, Cisco provided robust capabilities for transitioning from IPv4 to IPv6, ensuring that network managers could adopt the newer standard without sacrificing performance or reliability. This included support for routing protocols and other networking functions that were essential in an IPv6 environment.

Performance improvements were also a key aspect of IOS 12.4. The release optimized routing protocols, including Enhanced Interior Gateway Routing Protocol (EIGRP) and Open Shortest Path First (OSPF), to enhance convergence times and reduce latency. This effectively contributed to improved network efficiency and uptime.

Cisco also included advanced Quality of Service (QoS) capabilities in IOS 12.4, allowing organizations to prioritize critical traffic. Features such as class-based weighted fair queuing and low-latency queuing became invaluable for organizations requiring seamless voice and video communications over IP networks. This focus on QoS demonstrated Cisco's understanding of the growing importance of multimedia applications in modern business environments.

With a set of stable and scalable routing features, IOS 12.4 supports a variety of platforms, enabling businesses to deploy it across different networking hardware to suit their needs. The modularity of this IOS version makes it flexible for various applications, from small business networks to large enterprise systems.

In summary, Cisco Systems' IOS 12.4 brought forth a wealth of features aimed at enhancing security, performance, and flexibility. Through improved routing capabilities, strong IPv6 support, and advanced QoS features, this version laid the foundation for many of the networking principles that organizations still utilize today.
Top Page Image Contents