BOB MA0201 operating instructions Sport Utility Stroller OWNER’S Manu, Assembly Instructions

Wrist Safety

Strap

Swing Arm

Sport Utility Stroller OWNER’S MANU

Handle Bar

&Brake Lever

Handlebar Release Lever

Canopy Flap

Seat Recline Adjusters

Slider Latch

Seat Back Pocket

Shock Absorber

Frame Release Handle

Shock Release Button

BOB is a company

that produces high quality products, which encourage a healthy, outdoor, car-free life-style. In addition to strollers, we also make single-

wheeled cargo trailers for bicycles. See www.bobgear.com for our complete line of products. Before attempting to assemble or use your new stroller, read and understand these operating instructions completely to insure proper assembly and operation. If you are unclear on any point, contact your dealer or BOB before use.

WARNINGS

Never leave children unattended in the stroller.

Failure to properly assemble or install the quick release wheels on this stroller may result in the wheels becoming detached while moving and a subsequent loss of control of the stroller.

Always use seat harnesses to avoid serious injury to children from sliding or falling out of stroller.

Never allow occupants to stand in stroller.

The parking brake is not designed as a stopping brake. The brake should not be used to slow or stop the stroller. The brake is intended to park the stroller on flat surfaces, not on inclines. Never leave your children in the stroller unattended with or without the parking brake set!

Do not strap parcels or bags to the handle as it affects the balance and stability of the stroller and can cause it to tip over backwards.

The maximum carrying capacity of the stroller is 70 pounds.

Do not place sharp objects in the seatback pocket as your child leans against this and can be injured as a result.

When starting out, always make sure that your kid’s hands and feet are away from wheel spokes.

The stroller is not equipped for use after dark. If you intend to use it at night, we recommend installing wheel reflectors and a lighting system available through your local bike shop.

We do not recommend wearing roller skates or in-line skates while pushing stroller.

BOB IS NOT RESPONSIBLE FOR INJURY, DAMAGE, OR FAILURE THAT RESULTS FROM OWNER’S FAULTY ASSEMBLY OR MAINTENANCE AFTER SHIPPING.

AGE RECOMMENDATIONS: - It is recommended that your child be a minimum of 6 to 8 weeks old before riding in the stroller. Young babies incapable of holding their head up must be provided additional head and neck support to ride safely. For jogging and off road use, children should be at least 6 to 8 months old. Children develop at different rates. Consult with your pediatrician regarding the suitability of the stroller use with your child.

ASSEMBLY INSTRUCTIONS:

Reference Fig. 1 as it describes the various parts of the stroller.

1UNPACK: Remove stroller, stroller wheels, front fender and front quick release from packaging. Plastic packaging material was used to protect the front fork dropouts, the front wheel axles and the shock slider brackets. Remove these plastic pieces.

Canopy	Sun Canopy
Drawstring

Seat Pockets

5Point

Safety Harness

Foot Well

Fender &

Brake

Assembly

Swing Arm		Fig. 1
		Anatomy of the
Pivot	Low Boy
		BOB Sport Utility Stroller

2SWINGARM: Rotate the swingarm away from the front of the stroller until the shocks engage in the first position (Fig. 2). The

shocks’ locking pins will “snap” and lock into position 1.

3 HANDLE: Rotate the stroller handle up to the fully open position. Slider Latches will lock into place (Fig. 3).

4 REAR WHEEL: Place the rear
wheel quick release lever in the
open position, as shown in Fig.
4. Insert the rear wheel’s stub	position #1
axle into the hole in the rear
	position #2
dropout. If the axle does not slide
	Fig. 2
in easily, loosen the quick release
adjuster nut (Fig. 4) by hand. Re-	Swingarm in unfolded position
insert the axle fully into the rear	with shock in position #1

dropout until the snap ring on the

axle comes in contact with the dropout (Fig. 5). Move the quick release

lever to the closed position (Fig. 6). The word CLOSE should be
clearly visible and
the quick release
lever should be
pointing up
towards the seat.
When properly	Handlebar Release
adjusted, it will
require	Lever
considerable
pressure (80-105
inch/pounds) to	Fig. 3	Slider Latch
close the lever. If
you do not feel this		Stroller with handle in the
resistance (too
loose or too tight),		unfolded position.
return the quick
release lever back
to the open		Quick Release Lever
position (Fig. 4),		In Fully Open Position
and adjust the
adjusting nut
(clockwise to
tighten,		Adjusting Nut
counterclockwise
to loosen). Move
the quick release	Fig. 4
lever to the closed
position (Fig. 6).		Rear wheel quick release with
NOTE: Follow all
		lever in open position.