BOB MA0201 operating instructions Ual, Front Wheel

Front Quick Release Anatomy

Fig. 9

Brake lever in the set position

with button depressed.

Cam Housing

Conical

Springs

Fig. 14

ParkingBrakeButton

Adjusting Nut

Quick Release Lever

Rod

Fig. 13

ParkingBrakeButton

Brake Lever

Body

Brake lever

Lock Ring Barrel Adjuster

7 PARKING BRAKE: The brake is a parking brake, it prevents the stroller from moving while loading and unloading it. The parking brake is not designed as a stopping brake. We do not recommend using the brake to slow or stop the stroller. The brake is intended to park the stroller on flat surfaces not on inclines. Never leave your children in the stroller

unattended with or without the parking

brake set! After installing the front

wheel, the brake caliper will need to be

placed in the closed

position. Close the brake quick release

(Fig. 10) by squeezing the brake pads against the wheel with your

right hand and rotating

the brake quick release lever in the

counter (over)

Fig. 12 Quick Release in the closed position and parallel to frame tube.

Fabric

Screw

Hole

Brake

Mounting

Plate Hole

Cross Tube Hole

Fig. 8 Fender Installation

Fabric Screw

Fender Hole

Fender Screw

Metal Tab Hole

Fabric Screw Fender Screws

Fig. 11 Front wheel dropouts

shown with wheel in correct position. Quick release lever perpendicular to the dropout.

Dropouts

Brake Pad

Brake

Pad Nut

Brake

Quick

Release

Lever

Lock

Nut

Brake & Fender

Mounting Screw

Barrel

Adjuster

Brake Body

10 mm Nut

Caliper Brake Anatomy

Fig. 10

The front fork’s dropouts are slotted to receive

the front wheel (Fig. 11). Slide the wheel into the dropouts so

that the quick

release lever is on the left hand side of the

stroller. Make sure the wheel is centered in the

frame and that the axle is

touching the back of the drop out slot.

Securely tighten the wheel in place as follows: With the quick release

lever in the open position (Fig. 11), tighten the adjusting nut

(clockwise) until it comes in contact with the stroller dropout. Move the quick release lever to the closed position (Fig. 12). This should require significant pressure. If you do not feel significant resistance, turn the quick release lever back to the open

position (Fig. 11), and hand tighten the adjusting nut by one or two more turns in the clockwise direction. Move the quick release lever toward the

closed position (Fig. 12). The word CLOSE should be clearly visible and the quick release lever should be parallel to the stroller frame tube. It should require considerable pressure (80-105inch-pounds) to close the lever when properly adjusted. NOTE: Follow all instructions exactly. If you are unsure how to operate the quick release, consult your dealer or call BOB.

MA0201

UAL	(800) 893-2447 www.bobgear.com email- bob@bobgear.com
	Phone: (805) 541-2554 Fax: (805) 543-8464,3641 Sacramento Dr. #3 San Luis Obispo, California 93401

instructions exactly. If you are unsure how to operate the quick release, consult your dealer or contact BOB.

5FENDER INSTALLATION: Before installing the front wheel, you will need to attach the fender. The two attachment screws can be found already installed on the frame (Fig. 7). Remove the two fender mounting screws. You may wish to remove a fabric screw (right or left) to give better access to the cross tube fender screw. Align the hole in the metal tab of the fender with the threaded hole in the center of the front cross tube and install screw (Fig.

8). Align the hole in the plastic fender with the hole in the brake mounting plate and install screw (Fig. 8). Center fender on stroller and tighten both screws.

Dropout

Snap Ring

Fig. 5 Rear wheel installed with

snap ring contacting dropout.

Fig. 6 Quick release in the

closed position.

Fig. 7 Fender Screws

6FRONT WHEEL:

(Fig. 9) shows the anatomy of the front wheel quick release.

Remove the adjuster

nut and one spring from the quick

release, and install

the quick release rod into the wheel axle.

Install the spring (small end towards

the center of the wheel) and screw on the adjuster nut by

turning in a clockwise direction. Tighten the nut only three turns (final adjustment will be made after the wheel is installed).

As the stroller’s tires are wider than the rims, and as the brake pads are adjusted to the rims, the brake caliper will need to be opened before mounting or removing the wheel. Open the brake quick release (Fig. 10) by squeezing the brake pads together with your right hand, and pulling

down and then rotating

the brake quick

release

lever outward with your left

hand.