Linear SWC, SWR, SWD manual Gate Operator Installation Checklist

Page 32

Gate Operator Installation Checklist

INSTALLER CUSTOMER

❑ ❑

❑ ❑

❑ ❑

❑ ❑

1.The gate has been checked to make sure it is level and moves freely in both directions.

2.Potential pinch areas have been guarded so as to be inaccessible OR have contact and/or non-contact obstruction sensing devices installed.

3.The installer has installed one or more contact or non-contact obstruction sensing devices, in compliance with UL325 requirements for this installation.

4.If pedestrian traffi c is expected, a separate pedestrian gate has been installed, a minimum of seven feet from the gate. The customer has been informed that all pedestrian traffi c must use the pedestrian gate.

❑ ❑

❑ ❑

❑ ❑

5.Warning signs have been installed on each side of the gate in highly visible locations. The customer has been informed that these signs must remain at all times.

6.There are no controls installed on the gate operator, or within seven feet of the gate.

7.The installer has properly adjusted the obstruction sensing feature and has tested the gate to make sure that the gate stops and reverses a short distance with minimal resistance applied (40 lbs. on a swing gate at the end of the gate, 75 lbs. on a slide gate)

❑ ❑

❑ ❑

8.The installer has instructed the customer in the proper use of the gate operator and reviewed all of the operational functions, obstruction sensing devices, warning beeper and reset, etc.

9.The installer has instructed the customer in the proper use of the operator’s manual disconnect feature. The manual disconnect must never be used while the gate is in motion. The power switch must be turned off before using the manual disconnect and disengaging the operator.

❑ ❑

❑ ❑

❑ ❑

10.The installer has reviewed all safety instructions with the customer, and has left the safety instructions and owner’s information sheets for their reference.

11.The installer has answered any questions the customer has regarding the operation of the gate operator and gate operator safety precautions.

12.The installer has explained to the customer that a regular maintenance schedule for both the gate and the gate operator is recommended.

By signing this installation checklist, I/we hereby certify that each item listed and checked above has been covered by the installer and is clearly understood by the customer.

Customer’s Signature

Date

Installer’s Signature

Date

SWR SWC SWD Swing Gate Operator Installation Guide

- 30 -

227965 Revision X13 3-28-2008

Image 32
Contents SWR SWC SWD Table of Contents Before You Begin Always Check the Gate’s ActionRegulatory Warnings Gate Operator ClassificationsDC Control and Accessory Wiring Wiring SpecificationsAC Power Wiring Mounting Pad Installation Mounting Pad SpecificationsGate Arm Installation Vent Plug InstallationSetting Left or Right Hand Configuration Gate Plate InstallationInstalling the Gate Arm on the Operator Setting the Arm LengthsChoosing Good Harmonics Good BAD HarmonicsOperator Setup Controller AccessAC Power Connection Connect AC Power Pigtail Leads to AC SourceLimit Cam Rough Adjustment Torque Limiter AdjustmentLimit Cam Fine Adjustment CamsButtons Controller FeaturesDisplay Indicator Descriptions Terminal Descriptions Operator Accessory Connections Operator Accessory ConnectionsBasic Controller Programming Run Alarm and Pre-start Alarm Maximum Open Direction Current SettingMaximum Close Direction Current Setting RUN Alarm PRE-START AlarmAdvanced Controller Programming Auxiliary Relay Mode Reverse Delay TimeLow Power Mode Power Failure ModeReset Cycle Count Maintenance Alert TriggerSoft Start/Stop Duration Mid-travel Stop PositionRadio Enable Antenna InstallationReset Controller to Factory Defaults Radio Transmitter LearnLoop Loop Layout IllustrationUSE Relief Cuts AT Corners Safety Edge Layout Illustration Retaining BracketPhotoeye Installation Illustration Refer to Connection Illustrations for DetailsDual Gate Installations Gate OperationError Indications Operation IndicationsTroubleshooting Model SWR Exploded View DescriptionModel SWC Exploded View Model SWD Exploded View SWR, SWC, SWD Gate Arm Assembly Exploded View Model SWD Maintenance Battery MaintenanceDC Motor Brush Replacement When NEWPreventative Maintenance Month Preventative MaintenanceFCC Notice GeneralGate Operator Installation Checklist

SWR, SWD, SWC specifications

Linear SWC (Single Wire Control), SWD (Single Wire Debug), and SWR (Single Wire Radio) are advanced communication protocols widely utilized in embedded systems and electronic applications. These protocols enhance the efficiency of data transmission, reduce the number of physical connections required, and simplify the design process for developers.

The main feature of Linear SWC is its ability to transmit control signals over a single wire, allowing for straightforward connectivity between microcontrollers and various peripherals. This approach minimizes the complexity of printed circuit boards (PCBs) and reduces the space needed for connections, making it ideal for compact designs. Linear SWC operates based on a master/slave architecture, where the master device initiates communication, and the slave devices respond.

SWD, primarily used for debugging embedded systems, is a two-pin interface that supports high-speed data transfer with minimal pin usage. Unlike traditional JTAG, SWD is simpler and more efficient, allowing developers to perform debugging and programming tasks with fewer resources. The SWD protocol offers features such as breakpoint management, memory read/write capabilities, and real-time variable monitoring, empowering developers to optimize their code and increase debugging efficiency.

SWR is focused on wireless communication, leveraging a single wire for transmitting radio signals. This technology is particularly advantageous in applications requiring minimal hardware while maintaining robust connectivity. SWR supports various modulation techniques and can operate in different frequency bands, making it versatile for various use cases. The single-wire approach reduces the complexity of antenna design and enhances the overall reliability of wireless communications in challenging environments.

One of the key characteristics shared by SWC, SWD, and SWR is their ability to reduce power consumption. By minimizing the number of connections and optimizing signal paths, these protocols significantly decrease the energy required for data transmission. Additionally, their compatibility with a wide range of microcontrollers and integrated circuits contributes to their widespread adoption in modern electronic designs.

In summary, Linear SWC, SWD, and SWR serve critical roles in the evolution of embedded systems, offering unique features, advanced technologies, and efficient characteristics. Their capability to simplify designs, reduce power consumption, and enhance overall communication quality makes them essential tools for engineers and developers in today's fast-paced technological landscape. As the demand for compact, efficient solutions grows, these protocols are poised to play an increasingly significant role in future innovations.