Linear SWC, SWR, SWD manual Loop Layout Illustration, USE Relief Cuts AT Corners

Page 20

SWR • SWC • SWD Swing Gate Operator Installation Guide - 18 -

227965 Revision X13 3-28-2008

USE RELIEF CUTS

AT CORNERS

SEPARATE PEDESTRIAN GATE REQUIRED

7 FT. MINIMUM DISTANCE AWAY FROM GATE

2" MAX.

 

WALL PARTIALLY

3/8"

TWIST WIRE FROM END OF

 

SHOWN FOR CLARITY

LOOP

LOOPS BACK TO OPERATOR

 

AT LEAST SIX TIMES PER

 

SEALANT

FOOT

 

2"

MULTIPLE TURNS

REFER TO LOOP

INSTALLATION NOTES

FOR DETAILS

6 FT.

OPEN

GATE

PARTIALLY

SHOWN

NOTE: POSITION SHADOW LOOP APPROXIMATELY HALF WAY

BETWEEN ENTRY AND EXIT REVERSING LOOPS. THE DISTANCE

BETWEEN THE SHADOW LOOP AND EXIT/REVERSING LOOPS

SHOULD NEVER EXCEED THE LENGTH OF THE SHORTEST

VEHICLE TYPE WHICH IS EXPECTED TO USE THIS GATE.

Loop Layout Illustration

Page 19 Page 21
Image 20
Page 19 Page 21
Contents SWR SWC SWD Table of Contents Before You Begin Always Check the Gate’s ActionRegulatory Warnings Gate Operator ClassificationsDC Control and Accessory Wiring Wiring SpecificationsAC Power Wiring Mounting Pad Installation Mounting Pad SpecificationsGate Arm Installation Vent Plug InstallationSetting Left or Right Hand Configuration Gate Plate InstallationInstalling the Gate Arm on the Operator Setting the Arm LengthsChoosing Good Harmonics Good BAD HarmonicsOperator Setup Controller AccessAC Power Connection Connect AC Power Pigtail Leads to AC SourceLimit Cam Rough Adjustment Torque Limiter AdjustmentLimit Cam Fine Adjustment CamsButtons Controller FeaturesDisplay Indicator Descriptions Terminal Descriptions Operator Accessory Connections Operator Accessory ConnectionsBasic Controller Programming Run Alarm and Pre-start Alarm Maximum Open Direction Current SettingMaximum Close Direction Current Setting RUN Alarm PRE-START AlarmAdvanced Controller Programming Auxiliary Relay Mode Reverse Delay TimeLow Power Mode Power Failure ModeReset Cycle Count Maintenance Alert TriggerSoft Start/Stop Duration Mid-travel Stop PositionRadio Enable Antenna InstallationReset Controller to Factory Defaults Radio Transmitter LearnLoop Loop Layout IllustrationUSE Relief Cuts AT Corners Safety Edge Layout Illustration Retaining BracketPhotoeye Installation Illustration Refer to Connection Illustrations for DetailsDual Gate Installations Gate OperationError Indications Operation IndicationsTroubleshooting Model SWR Exploded View DescriptionModel SWC Exploded View Model SWD Exploded View SWR, SWC, SWD Gate Arm Assembly Exploded View Model SWD Maintenance Battery MaintenanceDC Motor Brush Replacement When NEWPreventative Maintenance Month Preventative MaintenanceFCC Notice GeneralGate Operator Installation Checklist

SWR, SWD, SWC specifications

Linear SWC (Single Wire Control), SWD (Single Wire Debug), and SWR (Single Wire Radio) are advanced communication protocols widely utilized in embedded systems and electronic applications. These protocols enhance the efficiency of data transmission, reduce the number of physical connections required, and simplify the design process for developers.

The main feature of Linear SWC is its ability to transmit control signals over a single wire, allowing for straightforward connectivity between microcontrollers and various peripherals. This approach minimizes the complexity of printed circuit boards (PCBs) and reduces the space needed for connections, making it ideal for compact designs. Linear SWC operates based on a master/slave architecture, where the master device initiates communication, and the slave devices respond.

SWD, primarily used for debugging embedded systems, is a two-pin interface that supports high-speed data transfer with minimal pin usage. Unlike traditional JTAG, SWD is simpler and more efficient, allowing developers to perform debugging and programming tasks with fewer resources. The SWD protocol offers features such as breakpoint management, memory read/write capabilities, and real-time variable monitoring, empowering developers to optimize their code and increase debugging efficiency.

SWR is focused on wireless communication, leveraging a single wire for transmitting radio signals. This technology is particularly advantageous in applications requiring minimal hardware while maintaining robust connectivity. SWR supports various modulation techniques and can operate in different frequency bands, making it versatile for various use cases. The single-wire approach reduces the complexity of antenna design and enhances the overall reliability of wireless communications in challenging environments.

One of the key characteristics shared by SWC, SWD, and SWR is their ability to reduce power consumption. By minimizing the number of connections and optimizing signal paths, these protocols significantly decrease the energy required for data transmission. Additionally, their compatibility with a wide range of microcontrollers and integrated circuits contributes to their widespread adoption in modern electronic designs.

In summary, Linear SWC, SWD, and SWR serve critical roles in the evolution of embedded systems, offering unique features, advanced technologies, and efficient characteristics. Their capability to simplify designs, reduce power consumption, and enhance overall communication quality makes them essential tools for engineers and developers in today's fast-paced technological landscape. As the demand for compact, efficient solutions grows, these protocols are poised to play an increasingly significant role in future innovations.
Top Page Image Contents