Yamaha RX-V630RDS owner manual For U.K. customers, Special Instructions for U.K. Model

Page 2

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

1To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference.

2Install this unit in a well ventilated, cool, dry, clean place with at least 30 cm on the top, 20 cm on the left and right, and 10 cm at the back of this unit

— away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold.

3Locate this unit away from other electrical appliances, motors, or transformers to avoid humming sounds. To prevent fire or electrical shock, do not place this unit where it may get exposed to rain, water, and/or any type of liquid.

4Do not expose this unit to sudden temperature changes from cold to hot, and do not locate this unit in a environment with high humidity (i.e. a room with a humidifier) to prevent condensation inside this unit, which may cause an electrical shock, fire, damage to this unit, and/or personal injury.

5On the top of this unit, do not place:

Other components, as they may cause damage and/or discoloration on the surface of this unit.

Burning objects (i.e. candles), as they may cause fire, damage to this unit, and/or personal injury.

Containers with liquid in them, as they may cause electrical shock to the user and/or damage to this unit.

6Do not cover this unit with a newspaper, tablecloth, curtain, etc. in order not to obstruct heat radiation. If the temperature inside this unit rises, it may cause fire, damage to this unit, and/or personal injury.

7Do not plug in this unit to a wall outlet until all connections are complete.

8Do not operate this unit upside-down. It may overheat, possibly causing damage.

9Do not use force on switches, knobs and/or cords.

10When disconnecting the power cord from the wall outlet, grasp the plug; do not pull the cord.

11Do not clean this unit with chemical solvents; this might damage the finish. Use a clean, dry cloth.

12Only voltage specified on this unit must be used. Using this unit with a higher voltage than specified is dangerous and may cause fire, damage to this unit, and/or personal injury. YAMAHA will not be held responsible for any damage resulting from use of this unit with a voltage other than specified.

13To prevent damage by lightning, disconnect the power cord from the wall outlet during an electrical storm.

14Take care of this unit so that no foreign objects and/or liquid drops inside this unit.

15Do not attempt to modify or fix this unit. Contact qualified YAMAHA service personnel when any service is needed. The cabinet should never be opened for any reasons.

16When not planning to use this unit for long periods of time (i.e. vacation), disconnect the AC power plug from the wall outlet.

17Be sure to read the “TROUBLESHOOTING” section on common operating errors before concluding that this unit is faulty.

18Before moving this unit, press STANDBY/ON to set this unit in the standby mode, and disconnect the AC power plug from the wall outlet.

19VOLTAGE SELECTOR (China and General models only)

The VOLTAGE SELECTOR on the rear panel of this unit must be set for your local main voltage BEFORE plugging into the AC main supply. Voltages are 110/120/220/240 V AC, 50/60 Hz.

This unit is not disconnected from the AC power source as long as it is connected to the wall outlet, even if this unit itself is turned off. This state is called the standby mode. In this state, this unit is designed to consume a very small quantity of power.

For U.K. customers

If the socket outlets in the home are not suitable for the plug supplied with this appliance, it should be cut off and an appropriate 3 pin plug fitted. For details, refer to the instructions described below.

Note

The plug severed from the mains lead must be destroyed, as a plug with bared flexible cord is hazardous if engaged in a live socket outlet.

Special Instructions for U.K. Model

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.

Making sure that neither core is connected to the earth terminal of the three pin plug.

CAUTION

Image 2
Contents Manual DE Instrucciones Gebruiksaanwijzing For U.K. customers Special Instructions for U.K. ModelContents Features About this manualControl Checking the package contentsGetting Started Controls and Functions Front panelSTEREO/EFFECT Remote control STEREO/EFFECT Using the remote controlHandling the remote control SET MenuFront panel display Speakers Speaker SetupSpeaker placement Connecting the speakers Diagram shows the speaker layout in the listening room Subwoofer jackImpedance Selector switch Impedance Selector switchConnecting to digital jacks ConnectionsConnecting video components Video monitor Indicates signal directionCable TV Game console or CamcorderConnecting a CD recorder or MD recorder Connecting audio componentsConnecting a CD player DSP-AX630SEConnecting a tunerSet up the AM loop antenna, then connect it Connecting the antennas RX-V630RDSConnecting the AM loop antenna 75-ohm/300-ohm antenna adapter U.K. modelConnecting an external decoder Connecting the AC power cord Connecting the power supply CordsTurning on the power Turn on the video monitor connected to this unitSpeaker Mode Settings Nrm Normal/-10 dBBefore you begin Adjusting Speaker Output LevelsUsing the test tone When adjustment is Adjust the levelEffect speakers using j So that it matches Level of the main SpeakersSelected input source Basic PlaybackTo select the audio source connected to the 6CH Input jacks To mute the sound When you have finished using this unitBGV background video function Input modes and indications Sub-program name Program name Program l / hProgram name Sub-program nameSelecting PRO Logic Press q/DTS SURVirtual Cinema DSP Playing Dolby Digital SurroundEX or DTS ES software Normal stereo reproductionHi-Fi DSP programs Digital Sound Field Processing DSPUnderstanding sound fields Recreating a sound fieldCINEMA-DSP Sound design of CINEMA-DSPDolby Pro Logic + DSP sound field effect Dolby Digital/DTS + DSP sound field effectDolby Digital EX/DTS-ES compatible + DSP sound field effect Dolby Pro LogicTable of Program Names for Each Input Format CINEMA-DSP programsFor movie programs No to For audio-video sources No to Sci-FiAutomatic tuning TuningAutomatic and manual tuning Manual tuningPresetting stations Automatically presetting stations for FM stationsPress Memory MAN’L/AUTO FM Manually presetting stationsTune in to a station Repeat steps 1 to 5 to store other stationsPress and hold PRESET/TUNING Edit for more than 3 seconds Tuning in to a preset stationExchanging preset stations Press PRESET/TUNING Edit againDescription of RDS data Changing the RDS modeReceiving RDS Stations PTY Seek function To cancel this functionPress PTY Seek Mode to set this unit PTY Seek mode EON functionCanceling the sleep timer Sleep TimerSetting the sleep timer To set the amount of timeRecording Special considerations when recording DTS softwareTimer playback/recording SET Menu Adjusting the items on the SETOn the remote control On the front panel Speaker SET speaker mode settings1A Center center speaker mode 1D Rear CT rear center speaker mode 1B Main main speaker mode1C Rear LR rear speaker mode 1E Bass LFE/bass out modeNrm SP DLY Time speaker delay time1F Main Lv main level mode 10 dBRange dynamic range R Balance balance Main left and right speakersAuto Input Mode initial input mode10 MEM. Guard memory guard LastControlling this unit Remote Control FeaturesControl area Controlling other componentClearing setup manufacturer code for the component control Setting the manufacturer codeClearing setup manufacturer Codes Controlling other components VCRFor 6ch Stereo Adjusting the Level of the Effect SpeakersPress j / i to adjust the speaker output level Subwoofer output levelAdjusting the Delay Time Press j / i to adjust the delay timeCT Width Center width Changing parameter settingsPRO Logic Music parameter Descriptions Troubleshooting GeneralOne side can be Sound suddenlyOnly the speaker on HeardNo sound from the rear center speaker Other settings on this Unit cannot be ChangedCheck SP Wires appears on the front panel display Humming soundRemote control Dolby Digital GlossaryDolby Surround DTS Digital Theater Systems Digital SurroundPCM Linear PCM Video signalComponent video signal Sampling frequency and number of quantized bitsSpecifications Admiral KTV VCR Cable TVSatellite Tuner CD Player DVD PlayerLD Player Tape Deck CD RECORDER/CD-RWMD Recorder V874860