Yamaha RX-V630RDS owner manual Connecting an external decoder

Page 20

CONNECTIONS

Connecting an external amplifier

If you want to increase the power output to the speakers, or want to use another amplifier, connect an external amplifier to the OUTPUT jacks as follows.

Note

•When RCA pin plugs are connected to the OUTPUT jacks for output to an external amplifier, signals are output from the SPEAKERS terminals as well.

1

2

3 4

 

 

OUTPUT

 

 

SUB

R

L

 

 

MAIN

REAR

 

CENTER

WOOFER

CENTER

 

 

 

 

OUTPUT

 

 

 

 

 

 

R

REAR

L

 

 

(SURROUND)

 

 

 

 

5

1SUBWOOFER jack

When using a subwoofer with built-in amplifier, including the YAMAHA Active Servo Processing Subwoofer System, connect the input jack of the subwoofer system to this jack. Low bass signals distributed from the main, center and/or rear channels are directed to this jack in accordance with your SPEAKER SET selections. The LFE (low-frequency effect) signals generated when Dolby Digital or DTS is decoded are also directed to this jack in accordance with your SPEAKER SET selections.

Notes

•The cut-off frequency of the SUBWOOFER jack is 90 Hz.

•If you do not use a subwoofer, designate the signals to the main left and right speakers by changing the settings of SPEAKER SET item “1E BASS” on the SET MENU.

•Use the control on the subwoofer to adjust its volume level. It is also possible to adjust the volume level by using this unit’s remote control (see “ADJUSTING THE LEVEL OF THE EFFECT SPEAKERS” on page 51).

2MAIN jacks

Main channel line output jacks.

Note

•The signals output through these jacks are affected by the BASS and TREBLE settings.

3REAR CENTER jack

Rear center channel line output jack.

4CENTER jack

Center channel line output jack.

5REAR (SURROUND) jacks

Rear channel line output jacks.

Connecting an external decoder

This unit is equipped with 6 additional input jacks (MAIN left and right, CENTER, SURROUND left and right, and SUBWOOFER) for discrete multi-channel input from an external decoder, sound processor, or pre-amplifier.

Connect the output jacks on your external decoder to the 6CH INPUT jacks. Be sure to match the left and right outputs to the left and right input jacks for the main and surround channels.

Notes

•When you select 6CH INPUT as the input source, this unit automatically turns off the digital sound field processor, and you cannot listen to DSP programs.

•When you select 6CH INPUT as the input source, settings of “1 SPEAKER SET” on the SET MENU do not apply (except for “1F MAIN Lv”).

18

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Manual DE Instrucciones Gebruiksaanwijzing For U.K. customers Special Instructions for U.K. ModelContents Features About this manualControl Checking the package contentsGetting Started Controls and Functions Front panelSTEREO/EFFECT Remote control Using the remote control Handling the remote controlSTEREO/EFFECT SET MenuFront panel display Speakers Speaker SetupSpeaker placement Connecting the speakers Diagram shows the speaker layout in the listening room Subwoofer jackImpedance Selector switch Impedance Selector switchConnecting to digital jacks ConnectionsConnecting video components Indicates signal direction Cable TVVideo monitor Game console or CamcorderConnecting audio components Connecting a CD playerConnecting a CD recorder or MD recorder DSP-AX630SEConnecting a tunerConnecting the antennas RX-V630RDS Connecting the AM loop antennaSet up the AM loop antenna, then connect it 75-ohm/300-ohm antenna adapter U.K. modelConnecting an external decoder Connecting the power supply Cords Turning on the powerConnecting the AC power cord Turn on the video monitor connected to this unitSpeaker Mode Settings Nrm Normal/-10 dBBefore you begin Adjusting Speaker Output LevelsUsing the test tone Adjust the level Effect speakers using j So that it matchesWhen adjustment is Level of the main SpeakersSelected input source Basic PlaybackTo select the audio source connected to the 6CH Input jacks To mute the sound When you have finished using this unitBGV background video function Input modes and indications Program l / h Program nameSub-program name Program name Sub-program nameSelecting PRO Logic Press q/DTS SURPlaying Dolby Digital Surround EX or DTS ES softwareVirtual Cinema DSP Normal stereo reproductionDigital Sound Field Processing DSP Understanding sound fieldsHi-Fi DSP programs Recreating a sound fieldCINEMA-DSP Sound design of CINEMA-DSPDolby Digital/DTS + DSP sound field effect Dolby Digital EX/DTS-ES compatible + DSP sound field effectDolby Pro Logic + DSP sound field effect Dolby Pro LogicTable of Program Names for Each Input Format CINEMA-DSP programsFor movie programs No to For audio-video sources No to Sci-FiTuning Automatic and manual tuningAutomatic tuning Manual tuningPresetting stations Automatically presetting stations for FM stationsManually presetting stations Tune in to a stationPress Memory MAN’L/AUTO FM Repeat steps 1 to 5 to store other stationsTuning in to a preset station Exchanging preset stationsPress and hold PRESET/TUNING Edit for more than 3 seconds Press PRESET/TUNING Edit againDescription of RDS data Changing the RDS modeReceiving RDS Stations To cancel this function Press PTY Seek Mode to set this unit PTY Seek modePTY Seek function EON functionSleep Timer Setting the sleep timerCanceling the sleep timer To set the amount of timeRecording Special considerations when recording DTS softwareTimer playback/recording SET Menu Adjusting the items on the SETOn the remote control On the front panel Speaker SET speaker mode settings1A Center center speaker mode 1B Main main speaker mode 1C Rear LR rear speaker mode1D Rear CT rear center speaker mode 1E Bass LFE/bass out modeSP DLY Time speaker delay time 1F Main Lv main level modeNrm 10 dBRange dynamic range R Balance balance Main left and right speakersInput Mode initial input mode 10 MEM. Guard memory guardAuto LastRemote Control Features Control areaControlling this unit Controlling other componentClearing setup manufacturer code for the component control Setting the manufacturer codeClearing setup manufacturer Codes Controlling other components VCRAdjusting the Level of the Effect Speakers Press j / i to adjust the speaker output levelFor 6ch Stereo Subwoofer output levelAdjusting the Delay Time Press j / i to adjust the delay timeCT Width Center width Changing parameter settingsPRO Logic Music parameter Descriptions Troubleshooting GeneralSound suddenly Only the speaker onOne side can be HeardOther settings on this Unit cannot be Changed Check SP Wires appears on the front panel displayNo sound from the rear center speaker Humming soundRemote control Glossary Dolby SurroundDolby Digital DTS Digital Theater Systems Digital SurroundVideo signal Component video signalPCM Linear PCM Sampling frequency and number of quantized bitsSpecifications Admiral KTV VCR Cable TVSatellite Tuner CD Player DVD PlayerLD Player Tape Deck CD RECORDER/CD-RWMD Recorder V874860
Top Page Image Contents