Pelco DX9100 installation manual Regulatory Notices, Radio and Television Interference

Page 8

REGULATORY NOTICES

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RADIO AND TELEVISION INTERFERENCE

This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

In order to maintain compliance with FCC regulations shielded cables must be used with this equipment. Operation with non- approved equipment or unshielded cables is likely to result in interference to radio and television reception.

8

C634M-D (12/04)

Image 8
Contents Recorder Contents Foreign Language Programming List of Illustrations Daily Event Recording List of Tables Important Safety Instructions Regulatory Notices Radio and Television InterferenceDescription Models Front View Recorder Back View Recorder Front View Viewstation Back View Viewstation Installation Installation Guidelines Mounting Rear Mounting Rail Screws Connections Viewstation Power Power UP the Equipment Viewstation Network Configuration ProgrammingChanging the VIEWSTATION’S Identification Changing the VIEWSTATION’S IP Address and Subnet Mask Click Properties. The following dialog box appears Changing the RECORDER’S Identification Time Synchronization Setting DATE/TIME Properties Client Configuration Utility C634M-D 12/04 DX9208F Frame Rate and Resolution Recorder Initialization OptionsC634M-D 12/04 Server State Go to Start Programs DX9000 Viewstation Server StateError Alert Database Backup and Repair Advanced Recorder OptionsDatabase Restoration System TrayClick Yes. Start/Continue is enabled after several seconds Databases Window Rename Mssql to MSSQLold Mssql Folders Delete MSSQLold C634M-D 12/04 Restore Utility Dialog Box Go to the system tray Start/Continue Window C634M-D 12/04 Finished Merging Dialog Box Click Close Restart the recorder Disabling the RAID Manager Gateway RAID Manager Gateway ConfigurationRAID Manager Utility Edit Server Window C634M-D 12/04 Gateway Configuration Settings Event NotificationNetsend Setting Viewstation IP Address C634M-D 12/04 RAID Manager Home C634M-D 12/04 Disk Information Plate IconSpare Hard Drive Information Host and RAID Information Plate Status Plate Camera Recording Properties Continuous Recording Schedule Continuous Recording Schedule Daily Recording ScheduleDaily Event Recording Weekly Recording Schedule Continuous Weekly Recording ScheduleMotion Detection Motion DetectionChannel Setup Parameter Description/Action Defining Users Edit Existing Users Manager InterfaceHandler Connecting AN Alarm Unit Alarm Unit Configuration CM9760 Alarm Driver Dialog Box Select CM9760ALM.dllClick Open. The following dialog box appears Manager for Alarm Unit Sample Configuration for External 1 Source Click Next. The following dialog box appears Connecting a Relay Unit Relay Unit Configuration CM9760 Relay Driver Dialog Box Select CM9760REL.dllClick Open. The following dialog box appears Manager for Relay Unit Click Next. The following dialog box appears Connecting a CM9760-CC1 Connecting a CM6800 Data Translator Configuration CM9760 Data Translator Driver Dialog Box Select CM9760DT.dllClick Open. The following dialog box appears Manager for Data Translator Click Next. The following dialog box appears DVR Management Data Translator ConnectionsConfiguring the Data Translator Click Configure. The following dialog box appears Connecting a CM9760-REL for DVR Management Relay Unit ConnectionsConfiguring the Relay Unit Click Configure. The following dialog box appears Foreign Language Programming Click Set Default. The following dialog box appears Service HOW to Replace a RECORDER’S Power SupplyHOW to Replace a RECORDER’S RAID 1 Drive To open the Promise Array Management UtilityC634M-D 12/04 Array Window Drive Cage Rebuilding System Array Specifications Viewstation 102 C634M-D 12/04 Warranty and Return Information ISO9001
Related manuals
Manual 86 pages 11.33 Kb