CAMERA/LENS Installation and Adjustments

4.3CAMERA/LENS INSTALLATION AND ADJUSTMENTS

To install the camera/lens combination, perform the following steps:

1.Disassemble the enclosure as specified in the Maintenance Section, Section 7.0.

CAUTION

Pressure must be released prior to opening the enclosure or per- sonal injury may result.

2.Install the camera/lens on the camera sled (Figure 10, item 11) by screwing the camera to the sled.

3.The enclosure power, lens functions and cam- era power should be connected as follows (also see Figures 7 and 8):

Pin # Function

AVideo core

BVideo shield

ECamera AC (high)

FCamera AC (low) G Ground

HEnclosure AC (high)

KIris

LFocus M Zoom

NLens Common

PEnclosure AC (low)

The EH8004, EH8006, EH8006-26 and EH8008 also include lens preset capabilities. Connections are as follows (refer to Figures 7 and 8):

Pin# Function

CPreset Positioning +5 V

DPreset Positioning Common

RPreset Positioning Focus

SPreset Positioning Zoom

Reinstall the camera sled into the body by follow- ing the steps shown in the Maintenance, Section 7.3.

4.4 MATING CONNECTOR ASSEMBLY

To assemble the 16 or 11 pin mating connector for the EH8000 Series Enclosures, perform the fol- lowing steps and refer to Figure 6. Note that enclosures supplied with an 11 pin connector will be wired according to the diagram in the bottom half of Figure 7 or 8.

1.Pass the coax and the enclosure control cable through the cable clamp body (item 5), the cable grommet (item 4), and the seal ring (item 3), in that order. Push those components down the cable approximately 10 inches (25 cm) to al- low yourself room to work.

2.Strip the outer jacket from the coax and the control cable back 2 inches. Strip the individual conductors of the control cable back 1/4 inch (0.63 cm).

3.Separate the coax shield from the core insu- lation and twist into a single strand. Strip the core insulation back 1 inch (3 cm).

4.Insert the individual conductors into the appro- priate holes into the sealing grommet (item 2) and force them through.

5.Solder the individual conductors to the appro- priate pins in the connector body (item 1).

6.Push the sealing grommet ( item 2) into the back of the connector body (item 1).

7.Slide the seal ring (item 3), the cable grommet (item 4), and the cable clamp body (item 5) for- ward to the connector body.

8.Thread the cable clamp body (item 5) onto the connector body (item 1) and tighten.

9.Position the cable clamp halves (item 6), and at- tach with the hardware supplied (items 7 and 8). The cable clamp halves should apply pressure to the cable grommet (item 4).Tighten all hard- ware.

6	Pelco Manual C418M (8/97)

EH8000 specifications

The Pelco EH8000 is a cutting-edge outdoor camera enclosure specifically designed to accommodate various security camera models while providing superior protection against environmental elements. With the rise of urban surveillance and the increasing importance of security measures, the EH8000 stands out due to its unique features and advanced technologies, making it a preferred choice among security professionals.

One of the primary characteristics of the Pelco EH8000 is its robust construction. The enclosure is made from heavy-duty aluminum, ensuring durability and a long service life, even in challenging weather conditions. This material not only resists corrosion but also provides an added layer of protection from vandalism and tampering, making it suitable for high-crime areas.

The EH8000 is designed to support a range of camera types, including PTZ, fixed, and varifocal cameras. This versatility allows installers to use the enclosure for various security applications without compromising on functionality. The internal mounting provisions are adjustable, providing flexibility to accommodate different camera models and sizes easily.

One of the standout features of the Pelco EH8000 is its integrated heater and blower system. This technology ensures optimal temperature control, preventing the internal components from overheating during hot weather and protecting the camera from freezing conditions in cold climates. This capability is particularly important for maintaining clear image quality, as extreme temperatures can negatively impact camera performance.

The enclosure supports a wide range of lenses and can be easily customized to fit specific security needs. It also features a built-in sunshade, which helps reduce glare and reflections that could compromise image clarity. The EH8000's design emphasizes streamlined aesthetics while ensuring high levels of functionality and effectiveness.

Installation of the Pelco EH8000 is straightforward, thanks to its modular design. The enclosure comes with a variety of mounting options, making it adaptable for different mounting surfaces, whether on walls, ceilings, or poles. The ease of installation translates into reduced labor costs and shortened project timelines, making it an economical choice for large-scale surveillance projects.

Furthermore, the EH8000 is equipped with weatherproof ratings, ensuring that it meets stringent standards for water and dust ingress protection. This level of security is crucial for outdoor setups where exposure to the elements is inevitable.

In summary, the Pelco EH8000 offers advanced protection for security cameras with its durable construction, versatile compatibility, integrated climate control, and customizable options. These features, combined with its ease of installation, make it a top choice for professionals looking to enhance their surveillance systems in outdoor environments.