Yamaha Connecting the antennas RX-V640RDS, Connecting the AM loop antenna, Notes, English

Page 15

Connecting the antennas RX-V640RDS

FM/AM

50kHz/9kHz

100kHz/10kHz

FREQUENCY

STEP

CONNECTIONS

Connecting the antennas RX-V640RDS

Both AM and FM indoor antennas are included with this unit. In general, these antennas should provide sufficient signal strength.

Connect each antenna correctly to the designated terminals.

AM loop antenna	Indoor FM
(included)	antenna
	(included)

■Connecting the AM loop antenna

1 Set up the AM loop antenna, then connect it to the terminals on this unit.

		2 Press and hold the tab to insert the AM loop
		antenna lead wires into the AM ANT and
		GND terminals.
	TUNER
	AM
	ANT
	GND	3 Orient the AM loop antenna for the best
	75Ω UNBAL.	3 Orient the AM loop antenna for the best
	75Ω UNBAL.	reception.
	ANT	reception.
	FM

Ground (GND terminal)

For maximum safety and minimum interference, connect the antenna GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth.

Notes

PREPARATION

75-ohm/300-ohm antenna adapter (U.K. model only)

1	2
	11	(7/16)
	8	(5/16)	Unit:
	6	(1/14)	mm (inch)
Open the cover of the	Cut the external sleeve
included 75-ohm/300-ohm	of the 75-ohm coaxial
antenna adapter.	cable and prepare it for
	connection.

3

Lead wire

Cut the lead wire and remove it.

4		5
Clamp	Clamp with
with	pliers.
pliers.
	Insert the wire	Snap the cover into
	into the slot.	place.
	into the slot.

Insert the cable wire into the slot, and clamp it with pliers.

•The AM loop antenna should be placed away from this unit.

•The AM loop antenna should always be connected, even if an outdoor AM antenna is connected to this unit.

A properly installed outdoor antenna provides clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may improve the quality. Consult the nearest authorized YAMAHA dealer or service center about the outdoor antennas.

FREQUENCY STEP switch (China and General models only)

Because the inter-station frequency spacing differs in different areas, set the FREQUENCY STEP switch (located on the rear panel) according to the frequency spacing in your area.

North, Central and South America:

100 kHz/10 kHz

Other areas: 50 kHz/9 kHz

Before setting this switch, disconnect the AC power plug of this unit from the AC outlet.

English

13

Image 15

Contents RX-V640RDS AV Receiver DSP-AX640SE AV Amplifier MANUAL DE INSTRUCCIONES GEBRUIKSAANWIJZINGCAUTION: READ THIS BEFORE OPERATING YOUR UNIT For U.K. customersSpecial Instructions for U.K. Model ADDITIONAL INFORMATION CONTENTSINTRODUCTION BASIC OPERATIONAbout this manual FEATUREScontrol Supplied accessoriesInstalling batteries in the remote GETTING STARTEDCONTROLS AND FUNCTIONS Front panela s d f INTRODUCTION English Remote control iSTEREO/EFFECT Using the remote controlHandling the remote control uMUTEy u i o p a Front panel display~~~~~~~~~~~~~~dB 0 q w e r tEnglish Before connecting componentsConnecting to digital jacks CONNECTIONSConnecting a recording component Connecting video componentsConnecting a video monitor Connecting a DVD player/digital TV/cable TVTV/digital TV cable TV VCR indicates audio signal directionEnglish DVD playerConnecting a tuner DSP-AX640SE Connecting audio componentsConnecting a CD player Connecting a CD recorder or MD recorderEnglish Connecting the antennas RX-V640RDSConnecting the AM loop antenna NotesConnecting an external amplifier Connecting an external decoderEnglish Connecting the speakersSpeaker placement SpeakersConnections IMPEDANCE SELECTOR switchREAR CENTER SPEAKER terminals MAIN SPEAKERS terminalsREAR SPEAKERS terminals CENTER SPEAKER terminalsAC OUTLETS SWITCHED Connecting the power supply cordsTurning on the power Connecting the AC power cordExit BASIC SYSTEM SETTINGSUsing the basic menu 1 SETUP2 SP LEVEL 1 SETUP4 SET/CANCEL SET MENUEnglish Setting the unit to match your speaker systemSetting speaker output levels SP LEVEL NotesAUTO PLAYBACKNight listening mode When you have finished using this unitBGV background video function To mute the soundNotes on playing DTS-CD/LDs Notes on digital signalsInput modes and indications AUTOEnglish AdventureGeneral Selecting a sound field programPlaying Dolby Digital EX or DTS ES material PRO LOGICMatrix Selecting PRO LOGIC, PRO LOGIC II or Neo:6Notes Virtual CINEMA DSPSILENT CINEMA DSP Normal stereo reproductionRecreating a sound field DIGITAL SOUND FIELD PROCESSING DSPUnderstanding sound fields Hi-FiDSP programsFor audio-videosources No. 4 to CINEMA-DSPSound design of CINEMA-DSP CINEMA-DSPProgramsStraight Decode For movie programsDolby Pro Logic + DSP sound field effect Sound field effectsDolby Digital/DTS + DSP sound field effect Dolby Digital EX/DTS-ES+ DSP sound field effectAAM 1530 kHz TUNINGAutomatic tuning Manual tuningNotes Presetting stationsAutomatically presetting stations for FM stations A1:FM 89.9 MHzC3:AM 1440 kHz Manually presetting stationsAAM 1440 kHz C :AM 1440 kHzA5:FM 90.6 MHz Selecting a preset stationExchanging preset stations E1:FM 87.5 MHzPTY Program Type mode PS Program Service name modeDescription of RDS data Changing the RDS modeTo cancel this function To cancel this functionPTY SEEK function EON functionSLEEP 120min L R SLEEP TIMERSetting the sleep timer Canceling the sleep timerEnglish Special considerations when recordingRECORDING DTS material3,5,8 Adjusting the items on the set menuSET MENU Set menu listThe last setting you adjusted speaker mode settingsSOUND 1 SPEAKER SET 1A CENTER center speaker mode1E BASS bass out mode 1B MAIN main speaker mode1C REAR LR rear speaker mode 1D REAR CT rear center speaker modeSOUND 3 LFE LEVEL Setting by “meters”Setting by “feet” SOUND 2 SP DISTANCE speaker distanceheadphone tone control SOUND 5 CENTER GEQ center graphic equalizerSOUND 6 HP TONE CTRL INPUT 1 I/O ASSIGN input output assignmentOPTION 3 AUDIO MUTE INPUT 2 INPUT MODE initial input modeOPTION 1 DISPLAY SET OPTION 2 MEM. GUARD memory guardOPTION 4 ZONE SET SP B speaker B setNotes Controlling other component REMOTE CONTROL FEATURESControl area Controlling this unitSetting the manufacturer code Clearing setup manufacturer codesNotes Controlling other components Notes SETTING THE SPEAKER LEVELSAdjusting the volume during playback Using the test toneChanging parameter settings SOUND FIELD PROGRAM PARAMETER EDITINGEnglish DELAY DIMENSIONDigital sound field parameter descriptions DSP LEVELTROUBLESHOOTING GeneralEnglish Refer to page EnglishProblem Remote controlTuner ProblemDolby Pro Logic GLOSSARYDolby Surround Dolby DigitalSampling frequency and number of quantized bits S-videosignalComponent video signal PCM Linear PCMFM SECTION SPECIFICATIONSAUDIO SECTION VIDEO SECTIONPage LIFETEC SATELLITE TUNER CABLE TVDVD PLAYER LD PLAYERCD PLAYER CD RECORDER/CD-RW MD RECORDERTAPE DECK WA69980 Printed in Malaysia