TP-Link TL-SC2020 manual Hardware Connection, Wall and Ceiling Mount

Page 13

2.4.2 Wall and Ceiling Mount

diameter is 4±0.2 mm.

2.4.2 Wall and Ceiling Mount

There are two ways to mount the Camera. See the following two pictures.

Ceiling Mount

Wall Mount

To mount the Camera, please follow the steps below:

1.Use the three supplied screws to fix the base plate to a flat surface.

2.Loosen the lock ring to adjust the desired angle of the Camera.

3.Tighten the lock ring.

2.5Hardware Connection

Before proceeding, confirm that your PC is connected to your router and can access the Internet. Make sure that your router’s DHCP feature is enabled. If not, please refer to your router’s instruction to enable it.

Please connect the Camera according to the following steps.

1.Connect the Camera to the LAN network (Router or Switch) via Ethernet cable.

2.Connect the power adapter cord to the Power Jack.

3.Plug the power adapter into the power outlet.

6

Image 13

Contents REV1.0.1 1910010670 TL-SC2020 Wired Network CameraCOPYRIGHT & TRADEMARKS CE Mark Warning FCC STATEMENTSafety Information Shennan Rd, Nanshan, Shenzhen, China DECLARATION OF CONFORMITYChapter 1 Safety Instructions Package ContentsChapter 2 Minimum System Requirement & Product Feature Chapter 3 Using Camera via Web BrowserC. System Requirement - Help to setup System access InternetAppendix ………………………………………………………………………………………35 Europe - EU Declaration of Conformity Note Package ContentsChapter 1 Safety Instructions 2.2 Product Features Chapter 2 Minimum System Requirement & Product Feature2.1 System Requirement  Note2.3 Physical Overview Power LED Indicator2.3.1 Front View 2.3.2 Rear View 2.4 Mount the Camera2.4.1 The Screw Size 2.4.2 Wall and Ceiling Mount 2.5 Hardware Connection3.1 Obtain the IP Address Chapter 3 Using Camera via Web Browserstart using the program 3.2 Windows Web Browser Page Chapter 4 Operating Camera via Mobile Phone 4.2 Using Camera via iPhone4.1 Mobile Phone Viewing 4.1.1 3G Mobile Phone Streaming Viewing Note 5.1 Home Chapter 5 Configuration of Main MenuSymbols Pause Stop Record Snapshot5.1.3 Digital zoom in/out the image via the monitor window 5.1.2 Snapshot5.1.4 Audio buttons Save Image5.2 Information 5.3 Basic setup5.3.1 Account To add a new account, please follow the steps below 5.3.2.1 TCP/IP 5.3.2 Network5.3.2.2 PPPoE 1 PPPoE Point-to-Point Protocol over Ethernet PPPoE is a network protocol for encapsulating Point-to-Point Protocol frames inside Ethernet frames. PPPoE connection is used mainly with ADSL service where individual users connect to the ADSL transceiver modem over Ethernet work. It also widely used in XDSL digital affiliate line such as ADSL, VDSL or SDSL  Periodical Update 5.3.2.3 DDNS Dynamic DNS2. Input all information and follow step by step with DynDNS 4. Type domain in the Hostname field and select sub-domain 5. After typing information, check your DDNS service5.3.2.4 UPnP Universal Plug and Play White Balance 5.3.3 Image Setting5.3.4 Video 5.3.6 Camera setting5.3.5 Audio 5.3.7.1 Motion detection 5.3.7 Events5.3.7.2 e-Mail SMTP  SSL Tick SSL box if the mail server you use has security restriction  Start Time, End Time Specify the Start Time and the End Time 5.3.7.3 FTP Note 5.4 System 5.4.1 Initialize 5.4.2 Date Time 5.5 Language B. Storage Requirement Table - Help to set Recording Storage System AppendixC. System Requirement - Help to setup System Clause EN 60950-1 EN 50392 EN 300 328 V1.6.1 Europe - EU Declaration of ConformityDescription Español Spanish Ελληνική Greek Français French Italiano Italian Svenska Swedish IMPORTANT NOTE FCC Radiation Exposure Statement Federal Communication Commission Interference Statement