JAI CV-A1-20 Edge Pre-select Mode, Table showing the figures for the different modes

Page 12

CV-A1-20

6.5. Edge Pre-select Mode

The exposure starts at the first HD pulse after the trigger leading edge. It stops and is read out after the duration of the shutter time selected. It can be the first 9 step in normal or 1023 steps in programmable shutter. SM=0 or SM=1. Shutter selections SH 10 will result in 1/8381 sec. This mode will operate with full and partial scanning and with all binning modes. Partial scanning together with binning will work, but it is not described, and no timing diagrams are documented. An EEN pulse will indicate the active accumulation time, and a WEN pulse indicates that the resulting video is being read out.

To use this mode:

 

 

Set function:

Trigger mode “Edge Pre-select”

TR = 1

 

Shutter mode “Normal” or “Programmable”

SM=0, SM=1

 

“Shutter Speed”

SH=0 through 9

 

“Programmable exposure”

PE=1 through 1023

 

Polarity and other functions

 

Input:

Ext. trigger to pin 5 on 6 pin connector (or pin 11 on 12-pin connector).

 

Ext. HD to pin 6 on12-pin connector. (If used).

 

Important notes on using this mode.

The start of exposure will start synchronized to the internal H signal. The start may be shifted max 1H. To avoid this shift (1 H jitter), synchronize the camera to an external HD and make sure that the trigger pulse aligns to the HD as shown in fig. 17.

The duration of the trigger should be >1H to <2000H.

A new trigger must not be applied before WEN is high.

In trigger modes there are no continuous VD out, only after each trigger input.

1H = 83.6 s

No equalize and serration pulses.

Table showing the figures for the different modes.

 

A

B

C

D

E

Max frame rate

Remarks

Scan mode

 

 

CCD array line #

Effective video

 

fps

 

Full

10H

14H

4 to 1038

1035H

18H

11

 

1/2 Partial

17H

33H

271 to 783

513H

25H

20

 

1/3 Partial

17H

33H

357 to 697

341H

25H

28

 

1/6 Partial

17H

33H

442 to 612

171H

25H

46

 

H binning

10H

14H

4 to 1038

1035H

18H

11

 

V binning

10H

14H

18 to 1019

501H

18H

22

 

V+H binning

10H

14H

18 to 1019

501H

18H

22

 

Fig. 20. Timing for Edge Pre-select with partial scanning and binning.

- 11 -

Image 12
Contents CV-A1-20 Table of Contents CV-A1-20Standard Composition Main Features GeneralLocations and Functions Pin Multi-connector DC-IN/VIDEO OUT, EXT.HD/VD Pin Multi-connector TriggerPin Assignment Input and Output Circuits Video outputTrigger input HD and VD inputCV-A1 Block Diagram Functions and OperationsBasic functions PWC H synchronous accumulation PWC asynchronous accumulation Input-output of HD/VD Signals Ext. HD and ext. VD phase conditionsContinuous Operation Non triggered External Trigger Modes Edge Pre-select Mode.TR=1Edge Pre-select Mode Table showing the figures for the different modesPulse Width Control Mode Pulse Width Control trigger modeFrame-delay read out Mode Frame Delay read out modeLong Time Exposure Mode Long time exposureStart/Stop Mode Start/Stop modeSmearless Mode Smearless ModeConfiguring the Camera Other FunctionsRS-232C control CV-A1-20 RS-232C command list Timing and shutter related commandsCamera Control Tool for CV-A1-20 External Appearance and Dimensions Internal Switch and Jumper SettingsSpecifications Spectral SensitivityPrecautions Typical CCD CharacteristicsAppendix Users Record Declaration of Conformity