NAD NAD 911 Introduction to the NAD-911 DIS- Tribution Preamplifier, Rear Panel Connections MIC

Page 4

GB

NAD 911 DISTRIBUTION PREAMPLIFIER

INTRODUCTION TO THE NAD-911 DIS- TRIBUTION PREAMPLIFIER.

The NAD-911 Distribution Preamplifier has been designed to control sound in multi-room or multi- speaker installations where both music and messag- ing is required. It will take mono or stereo signals from a mixer or hi-fi preamplifier and control the distri- bution of sound in up to six separately controllable speaker zones. Each level control will alter the vol- ume of one particular speaker zone so that the sys- tem can deliver music at different levels in different areas of the installation. With the built-in microphone section, the NAD-911 can selectively deliver announcements and messages to individual parts of the system.

Several NAD-911s can be connected together to control music and messages in larger installations. With a range of internal configuration presets, the NAD-911 has the flexibility to be configured to match the needs of most setups.

This manual outlines the use of the NAD-911 in the most common types of installation. The unit can also be configured for a wide range of specialist setups and a qualified installation engineer will be able to advise on connecting and configuring the NAD-911 within more complex installations.

REAR PANEL CONNECTIONS.

1.MIC IN

Input for a Microphone. This Input is suitable for most medium to high impedance microphones.

The microphone circuitry has a bass roll-off filter that will reduce low frequency microphone handling noises being passed to the speakers. A limiter has been added to the microphone circuit to reduce over- load distortion on very loud sounds. The Microphone is selected by using the front panel MASTER INSERT button (6) together with the individual channel INSERT buttons (4) and adjusting MICROPHONE LEVEL control (5). Plugging in a microphone into this socket automatically switches off the LINE INSERT IN connector.

2.LINE INSERT IN

Input for a line level source. This is used as an alternative to the microphone for message sources such as pre-recorded announcements. This is only active when MIC IN is unused. The MIC IN and LINE INSERT IN signal can be at a fixed or variable level depending on the settings of the internal configuration presets.

IMPORTANT INFORMATION.

The NAD- 911 should be placed on a firm level sur- face. Dampness can damage electronic components, so the unit should not be placed in areas of high humidity or where liquid could be splashed on it or spilt over it.

If liquid is spilt over the unit then disconnect from the AC socket and have the unit inspected by quali- fied service personnel before attempting to use it again.

The NAD-911 uses standard RCA and 1/4” jack connections and it is recommended that you use high quality connectors and cables throughout the installa- tion as this will improve the reliability and the overall performance of the system.

If the unit is not going to be used for some time, disconnect the power plug from the AC socket.

There are installation presets inside the unit and these should be adjusted by qualified installation per- sonnel only. Ensure the top cover is securely replaced before using your NAD Distribution Preamplifier.

3.MIC LINE OUT

Direct output for the microphone signal. The NAD- 911 amplifies the microphone input to line level so it can be used as the microphone feed to additional NAD-911s in a larger installation. The output of this socket can be at a fixed or variable level depending on the settings of the internal configuration presets.

4.INPUT (CHANNELS 1 -6)

Line level inputs for each of the six channels. These can be connected to any type of audio system such as a hi-fi preamplifier, cassette deck, CD player, mixer or the audio outputs of a video player. For mono sources use a single channel, for stereo sources use two adjacent channels.

5.FIXED OUT (CHANNELS 1-6)

Direct output for each channel. The level of the signal on this connector remains the same regardless of the front panel level controls. The INSERT signal does not appear on the FIXED OUT connections. The level is suitable for driving standard hi-fi components and amplifiers and can be used with leads up to 1nF total capacitance.

CLEANING.

Use a soft cloth to clean the NAD-911. If neces- sary, lightly dampen the cloth with soapy water. Do not use solutions containing benzol or other volatile agents.

6.VARIABLE OUT (CHANNELS 1-6)

Direct output for each channel. The level of the signal on this connector is altered by the front panel LEVEL controls (5). The INSERT signal will appear mixed on the VARIABLE OUT connections when selected by pressing the INSERT buttons. At its high- er settings of the LEVEL control, this output will drive professional (20dBu/600ohm) amplifiers. The variable output has a low impedance so it can be used to drive long cable runs up to 22nF total capacitance.

NAD

4

7.POWER CABLE

Fixed power AC cord for connection to AC socket.

Page 3 Page 5
Image 4
Page 3 Page 5
Contents NAD Important Safety Instructions Rear Panel Connections Front Panel Controls Cleaning Introduction to the NAD-911 DIS- Tribution PreamplifierRear Panel Connections MIC Important InformationFront Panel Controls Channels 1Microphone CablesBasic Connection and Operation Using Several NAD-911s TAMPER-PROOF CoversConfiguring the NAD-911 Internal Jumpers SERVICING, Installation and CON- Figuration IntructionsLevels Configuration Settings No Line Level Insert Signal No Microphone Signal or FeedbackNo Sound No Sound ONE ChannelInformations Importantes Branchements SUR LE Panneau ArriereCommandes SUR LA Face PAR- Lante Cables Branchement DES EntreesConnexion ET Fonctionnement DE Base Interconnexion DES VoiesFonctionnement DE Base Couvercles ANTI-DEREGLAGE Configuration DES Cavaliers Internes DU NAD-911 Configuration Utilisee Tion Variable INS VariableRecherche DES Pannes Wichtige Information RückwandverbindungenReinigung MICKanäle Bedienung AN DER GerätefrontMikrofon Kabel Verbindung DER EingängeDIE Verbindung VON Kanälen Verbindung DER OUTPUT-BUCHSENDIE Verteilung DES Insert Signals AN Alle Kanäle DIE Verteilung DES Insert Signals AN Bestimmte KanäleEinstellung DER Mikrofonlautstärke Allgemeine BedienungEinstellungsschutzabdeckungen SERVICE, Installation UND Bedienungsanweisungen Insert SystemkonfigurationKonfiguration DER Internen NAD-911 Jumpereinstellung Konfiguration DER MIKROFON- UND MusikeinstellungenAusschaltung DES MIKROFONEIN- Satzes AUF Einem Kanal Verbindung VON Mikrofon UND EingangslautstärkeKonfiguration DER Einstellungen Fehlerbehebung NAD 911 Technical Specifications THD+NNAD Electronics

NAD 911 specifications

The NAD NAD 911 is a significant addition to the realm of audio amplification, showcasing the brand's commitment to producing high-quality audio equipment. This model has garnered attention due to its refined sound reproduction capabilities, which appeal to both audiophiles and casual listeners alike.

At the core of the NAD 911 is its powerful amplification system, featuring a robust power output that suits a wide range of speaker configurations. With a clean and dynamic sound, this amplifier is designed to handle everything from delicate classical music to intense rock anthems, providing a rich auditory experience. The specifications boast an impressive wattage per channel, ensuring that listeners can enjoy their favorite tracks at satisfying volumes without distortion.

One of the standout technologies integrated into the NAD 911 is its proprietary PowerDrive technology. This feature optimizes power delivery to the speakers, adapting the amplifier's output to the demands of the connected load. It allows the NAD 911 to maintain high performance, delivering maximum output when required while providing a smooth and controlled sound even at high volumes.

In addition to its amplification prowess, the NAD 911 is designed with user convenience in mind. The amplifier includes a well-thought-out input selection process, offering multiple inputs to accommodate various audio sources. This makes it easy for users to connect their CD players, turntables, and streaming devices. With a simple and intuitive layout, the NAD 911 is accessible even for those who may not be tech-savvy.

The build quality of the NAD 911 reflects the brand's longstanding reputation for durability and reliability. The chassis is crafted from high-grade materials, ensuring that the amplifier can withstand the rigors of daily use while maintaining its performance integrity.

Moreover, the NAD 911 features advanced heat dissipation mechanisms, which help it operate efficiently without overheating. This not only prolongs the lifespan of the components but also contributes to the overall sound quality by minimizing interference.

Overall, the NAD NAD 911 strikes a fine balance between performance, versatility, and user-friendly design. It embodies the essence of NAD’s commitment to delivering high-fidelity sound experiences, making it an ideal choice for anyone looking to enhance their home audio setup. With its blend of innovative technology and classic audio engineering, the NAD 911 is set to leave a lasting impression in the audio community.
Top Page Image Contents