Front Panel, Bridging, Soft Clipping, Power

mode or with low-impedance loudspeakers. Connect the loudspeakers with heavy-duty (16-gauge or thick- er) stranded wire.

Connections may be made in either of two ways. [See Figure 2.]

(1)Strip off a half-inch (1 cm) of insulation from each speaker wire. In each conductor, twist the thin strands of wire together. Unscrew the knob, insert the bare wire into the opening at the base of the bind- ing post, and tighten the knob until it grasps the wire securely. Check to be sure that no loose strand of wire is touching the chassis or an adjacent terminal.

(2)Install banana plugs on your speaker wires, and plug them into the end of each binding post. The terminals are separated by 3/4 inch (19mm), so they will accept dual-banana plugs.

Connect the wires from the left-channel speaker to the CH 1 + and CH 1 - terminals and the wires from the right-channel speaker to the CH 2 + and CH 2 - terminals.

NOTE — Stereo speakers must operate in phase with each other in order to produce a focused stereo image and to reinforce rather than cancel each other’s output at low frequencies. When connecting speakers, take care that the red (positive) terminal on each loudspeaker is connected to the corresponding red (positive) terminal on the amplifier.

6. BRIDGING

The two amplifiers within the Model 912 can be “bridged” to form a single amplifier of about three times the power per channel.

To convert to bridged operation:

(1)Switch the POWER off.

(2)Disconnect any input and output cables.

(3)Set the bridging switch to ON.

(4)Select the cable from the speaker that is to be driven by the 912. Connect its “positive” conductor to the CH 1 + terminal and its “negative” conductor to the CH 2 + terminal (i.e. to the two red terminals). DO NOT connect any wires to the black terminals (CH 1 - and CH 2 -).

CAUTION: In the bridged mode, wires must be connected directly from the amplifier to the speakers, not to a speaker switch, headphone adapter, or any other device that shares a common ground between channels.

(5)Connect the signal lead from the source chosen to be amplified by the bridging amplifier to the input socket of the CH 1 amplifier.

(6)Turn the POWER on.

NOTE — If you are using two pairs of speakers on one channel, or if you are in the bridged mode, we recommend that the speakers have a nominal imped- ance of 8 or more.

7. SOFT CLIPPING

When an amplifier is driven beyond its specified power output it normally produces “hard clipping” of the signal with harsh distortion and power-supply buzz as the output transistors saturate. The NAD

SOFT CLIPPING circuit gently limits the output wave- form and minimizes audible distortion when the amplifier is overdriven. We recommend that it be switched ON when playing music at levels that might exceed the amplifier’s power capacity.

FRONT PANEL

1. POWER

Press this button to switch the amplifier on or off. A green LED above the power button illuminates when the power is on.

NAD

912 specifications

The NAD 912 is a prominent piece of audio equipment renowned for its exceptional sound quality and robust performance. As part of NAD's celebrated lineup of audio products, the 912 is specifically designed to cater to the needs of audiophiles and music enthusiasts looking for a powerful amplifier that can enhance their listening experience.

One of the main features of the NAD 912 is its powerhouse performance, boasting a significant output power that can drive even the most demanding speakers with ease. With a rated output of 100 watts per channel into 8 ohms, and the ability to drive lower impedance loads without compromising sound quality, the 912 ensures that music is delivered with clarity and authority across all frequencies.

The NAD 912 utilizes advanced technologies that set it apart from many of its competitors. Among these is the innovative PowerDrive technology, which allows the amplifier to deliver consistent power levels regardless of the load impedance. This ensures that the sound remains dynamic and punchy without introducing distortion even at high volume levels. NAD’s proprietary Soft Clipping feature further enhances the listening experience by allowing the amplifier to handle transient peaks smoothly, preserving musical integrity while preventing harsh clipping.

In addition to its robust power and performance capabilities, the NAD 912 incorporates a variety of input options, making it compatible with a vast array of audio sources. The back panel features multiple RCA inputs, allowing users to connect various devices such as CD players, turntables, and streaming devices. The inclusion of a rear speaker terminal facilitates easy connections to speakers, while the option for bi-wiring enhances connectivity and sound quality.

Another noteworthy characteristic of the NAD 912 is its build quality. Constructed with a solid chassis and high-quality components, this amplifier is designed to last and withstand the rigors of daily use. The sleek design not only adds to its visual appeal but also aids in heat dissipation, thereby promoting long-term reliability.

In conclusion, the NAD 912 stands out as a premium amplifier that combines high-performance audio engineering with user-friendly features. Its impressive output, advanced technologies, versatile connectivity options, and durable design make it an ideal choice for anyone looking to elevate their audio experience while enjoying the rich and detailed sound that NAD is known for. Whether used in a home stereo setup or as part of a larger audio system, the NAD 912 proves to be a worthy investment for discerning listeners.