NAD 163AV owner manual Specifications, AV Tuner Preamplifier, PRE-AMP Section, Tuner Section

Page 32

SPECIFICATIONS

AV TUNER PREAMPLIFIER	T 163

Decoding Formats	Dolby Digital, Dolby Pro Logic II, DTS-ES, NEO:6, Dolby EX

Sampling Rates	32 kHz, 44.1 kHz, 48 kHz, 96 kHz (PCM)

PRE-AMP SECTION

Input sensitivity and impedance	400mV / 50k ohms

IM distortion	0.08%

Total harmonic distortion	0.08%

Frequency response	5 to 20,000 Hz ±0.8dB

Signal/noise ratio; ref to 2V output	> 90dB

Signal/noise ratio; ref 500mV Input / 500mV output	> 80dB

Remote Control	HTR 2 / ZR 2

Maximum output level	> 5V RMS

Output Impedance	< 100Ω (PRE OUT)

TUNER SECTION

Input sensitivity Mono	16.1dBf

50dB Stereo:	36.1dBf

Harmonic Distortion; FM Mono	0.25%

Harmonic Distortion; FM Stereo	0.5%

Signal / noise; Mono	60dB

Signal / noise; Stereo	55dB

Stereo separation at 1kHz	40dB

Frequency Response; ± 1.5dB	30Hz - 15kHz

PHYSICAL SPECIFICATIONS

Dimensions (W x H x D)	17-1/8 x 5-15/16 x 15-3/8"
	(435 x 150 x 399 mm)

Net Weight	17.6 lbs (8 kg)

Shipping Weight	22.4 lbs (10.2 kg)

Specifications are subject to change without notice. For updated documentation and features please log onto www.nadelectronics.com for the latest information about your T 163.

32

Image 32

Contents 163 Safety Information Explanation of Graphical SymbolsPrecautions InstallationElectric Power MaintenanceDamage Requiring Service Do not Attempt to Service the Unit Yourself OWNER’S RecordTable of Contents Getting the Most from the NAD T Using the HTR 2 Remote ControlTroubleshooting Specifications Unpacking and Setup Connecting AM AntennaWHAT’S in the BOX Choosing a LocationAbout the T R.S., Matrix and Digital SurroundEase of USE IntegrationUpgradability About the HTR 2 System Remote Control Quickstart Play a DVD MovieFront Panel SearchDigital Input Jack Rear Panel Rear Panel Connecting the T 163 to a MULTI-CHANNEL Amplifier Dealing with HUM and Noise Setting UP the TGetting Started Input Setup Input SettingsAbout the ON-SCREEN Displays OSD and FRONT-PANEL Readout Display the OSDSpeaker Setup Speaker SettingsListening Mode Front L/RCHANNEL-BALANCE Test Setup Using AN SPL MeterSetting Channel Balance Setting Speaker DistanceCreating Presets Recalling PresetsUsing the T Tuning Stations Setting Radio PresetsSelecting Radio Presets Choosing the FM Mute / ModeDTS-ES Expanded Surround DTS ES DTS-ES DiscreteDTS-ES Matrix DTS NEO 6 SurroundDolby PRO Logic Dolby PRO Logic II SurroundDolby PRO Logic II Movie Dolby PRO Logic II MusicDTS Displaying the Signal ModeSelecting Listening Modes Adjusting Listening Modes Surround Sound Channel Chart Adjusting Channel Levels on the FLYTo Adjust Channel Levels Adjusting the Tone ControlsUsing the HTR 2 Remote Control SpecificationsControlling the T Learning Codes from Other RemotesCopy a Command from Another KEY Macro CommandsPUNCH-THROUGH Recording MacrosKEY-ILLUMINATION Timeout Factory ResetDelete Mode Loading CODE-LIBRARIESUsing the ZR 2 Remote Control Trigger SetupSummary of HTR 2 Modes Assigning the Trigger OutputCondition Possible Causes Possible Solutionss Specifications Physical SpecificationsAV Tuner Preamplifier PRE-AMP SectionNAD