NAD 163AV owner manual Quickstart, Play a DVD Movie

Page 9

QUICKSTART

In case you simply cannot wait to experience the performance of your new NAD T 163 tuner preamplifier, we provide the following “Quickstart” instructions to get you underway. The steps below connect your DVD player and multi-channel amplifier to the T 163; be sure to read “Input Setup”.

PLAY A DVD MOVIE

Connect the T 163’s preamplifier outputs to your multi-channel amplifier. (cables not supplied)

Connect the T 163’s composite video or S-Video MONITOR OUT jack to your TV/monitor’s corresponding input. (cables not supplied)

Connect your DVD player’s composite video or S-Video output to the T 163’s corresponding DVD input. (cables not supplied)

Connect the DVD player’s optical digital output to the T 163’s optical DIGITAL IN 1 input (Optical cable not supplied).

Connect your left and right front speakers to the multi-channel amplifier’s FRONT L and R outputs, being sure to connect red to red (“+”) and black to black (“-”), with care to avoid stray wires or strands crossing between terminals. (Connect center, surround, and surround-back speakers as well, if you like). If your system includes a powered subwoofer, connect the T 163’s AUDIO PRE-OUT SW1, 2 or both jacks to its line inputs.

Press in the main power switch (black pushbutton) on the T 163’s rear panel (this puts the T 163 into STANDBY mode and illuminates an amber LED to indicate it is ready to receive remote commands), then use the HTR 2’s [ON] key to power up the tuner preamplifier. Be sure the multi-channel amplifier and TV/ monitor is powered up, with the correct input selected.

Start playback of the DVD player. Press the HTR 2 remote’s [Amp] Device Selector key, and then its (red) DVD/numeric 1 key to select the DVD input. You should hear multichannel or stereo sound, and see an image on the TV/monitor. (If one or the other fails to appear, you may need to use the tuner preamplifier’s on-screen menu system to check assignment of audio, video, and digital inputs; see “Setting Up the T 163”.)

Enjoy the movie or music, but be sure to set aside time to read this manual thoroughly, and to set up, calibrate, and configure your T 163 carefully and completely.

ENGLISH

9

Image 9
Contents 163 Explanation of Graphical Symbols Safety InformationPrecautions InstallationMaintenance Electric PowerDamage Requiring Service Do not Attempt to Service the Unit Yourself OWNER’S RecordTable of Contents Using the HTR 2 Remote Control Troubleshooting SpecificationsGetting the Most from the NAD T Connecting AM Antenna Unpacking and SetupWHAT’S in the BOX Choosing a LocationR.S., Matrix and Digital Surround About the TEase of USE IntegrationUpgradability About the HTR 2 System Remote Control Play a DVD Movie QuickstartSearch Front PanelDigital Input Jack Rear Panel Rear Panel Connecting the T 163 to a MULTI-CHANNEL Amplifier Setting UP the T Getting StartedDealing with HUM and Noise Input Settings Input SetupAbout the ON-SCREEN Displays OSD and FRONT-PANEL Readout Display the OSDSpeaker Settings Speaker SetupListening Mode Front L/RUsing AN SPL Meter CHANNEL-BALANCE Test SetupSetting Channel Balance Setting Speaker DistanceRecalling Presets Creating PresetsUsing the T Setting Radio Presets Tuning StationsSelecting Radio Presets Choosing the FM Mute / ModeDTS-ES Discrete DTS-ES Expanded Surround DTS ESDTS-ES Matrix DTS NEO 6 SurroundDolby PRO Logic II Surround Dolby PRO LogicDolby PRO Logic II Movie Dolby PRO Logic II MusicDisplaying the Signal Mode Selecting Listening ModesDTS Adjusting Listening Modes Adjusting Channel Levels on the FLY Surround Sound Channel ChartTo Adjust Channel Levels Adjusting the Tone ControlsSpecifications Using the HTR 2 Remote ControlControlling the T Learning Codes from Other RemotesMacro Commands Copy a Command from Another KEYPUNCH-THROUGH Recording MacrosFactory Reset KEY-ILLUMINATION TimeoutDelete Mode Loading CODE-LIBRARIESTrigger Setup Using the ZR 2 Remote ControlSummary of HTR 2 Modes Assigning the Trigger OutputCondition Possible Causes Possible Solutionss Physical Specifications SpecificationsAV Tuner Preamplifier PRE-AMP SectionNAD