Yamaha RX-V459 Dolby Digital or DTS, Sources cannot be, Played. Dolby Digital, Or DTS indicator

Page 86

TROUBLESHOOTING

Problem

Cause

Remedy

See

page

 

 

 

Dolby Digital or DTS

The connected component is not set to

Make an appropriate setting following the operating

—

sources cannot be

output Dolby Digital or DTS digital

instructions for your component.

 

played. (Dolby Digital

signals.

 

 

or DTS indicator in

 

 

 

“INPUT MODE” is set to “ANALOG”.

Set “INPUT MODE” to “AUTO” or “DTS”.

32

the front panel

display does not light

 

 

 

up.)

 

 

 

 

 

 

 

A humming sound is

Incorrect cable connections.

Connect the audio cables firmly. If the problem

—

heard.

 

persists, the cables may be defective.

 

 

 

 

 

The volume level

The component connected to the AUDIO

Turn on the power of the component.

—

cannot be increased,

OUT (REC) jacks of this unit is turned

 

 

or the sound is

off.

 

 

distorted.

 

 

 

 

 

 

 

The sound effect

It is not possible to record the sound effect

 

 

cannot be recorded.

with a recording component.

 

 

 

 

 

 

A source cannot be

The source component is not connected to

Connect the source component to the analog AUDIO

18–20

recorded by an

the analog AUDIO IN jacks of this unit.

IN jacks.

 

analog component

 

 

 

connected to the

 

 

 

AUDIO OUT (REC)

 

 

 

jacks.

 

 

 

 

 

 

 

The sound field

“MEMORY GUARD” in “SET MENU”

Set “MEMORY GUARD” to “OFF”.

75

parameters and some

is set to “ON”.

 

 

other settings of this

 

 

 

unit cannot be

 

 

 

changed.

 

 

 

 

 

 

 

This unit does not The internal microcomputer has been

operate properly. frozen by an external electric shock (such as lightning or excessive static electricity) or by a power supply with low voltage.

Disconnect the power cable from the AC wall outlet

—

and then plug it in again after about 30 seconds.

 

“CHECK SP WIRES” appears in the front panel display.

Speaker cables are short-circuited.

Make sure all speaker cables are connected correctly.

12

There is noise

This unit is too close to the digital or high-

Move this unit further away from such equipment.

—

interference from

frequency equipment.

 

 

digital or radio

 

 

 

frequency equipment.

 

 

 

 

 

 

 

The picture is

The video source uses scrambled or

 

 

disturbed.

encoded signals to prevent dubbing.

 

 

 

 

 

 

This unit suddenly

The internal temperature becomes too

Wait about 1 hour for this unit to cool down and then

—

enters the standby

high and the overheat protection circuitry

turn it back on.

 

mode.

has been activated.

 

 

 

 

 

 

84

Page 85 Page 87
Image 86
Page 85 Page 87
Contents RX-V459 For U.K. customers Special Instructions for U.K. ModelContents Features Getting Started Supplied accessoriesInstalling batteries in the remote control Check that you received all of the following partsControls and Functions Remote control sensorPRESET/TUNING l / h, Level +/- buttons Front panelSpeakers A/B buttons Front panel displayPhones Silent Cinema jack BASS/TREBLE +/- buttonRemote control Controlling this unitControlling the Tuner functions Using the remote controlB/C/D/E j / i, PRESET/CH u / d Numeric buttonsFront panel display HiFi DSP indicator Headphones indicatorNight indicator Sleep indicatorRear panel Asia and General models onlyConnections Placing speakersFront Connecting speakersFront speakers a Right Left Surround speakers CenterSurround terminals Front terminalsCenter terminals Surround Back terminalsLoosen the knob Connecting the speaker cableTighten the knob to secure the wire Audio jacks Video jacksVideo signal flow for Monitor OUT Audio and video signal flowAudio signal flow for Audio OUT REC Connecting a TV DVD Player Connecting a DVD player, a DVD recorder, a VCR or an STBConnecting a DVD player DVD recorder or Connecting a DVD recorder or a VCRConnecting an STB Cable TV receiver or Satellite receiverMD recorder or tape deck Connecting a CD player, an MD player or a tape deckCD Player Connecting a multi-format player or an external decoder PlayerSet up the AM loop antenna Connecting the AM loop antennaOther lead wire to the GND terminal Repeat steps 2 through 4 to connectMemory back-up Connecting the power cableAsia and General models only Following display appears in the front panel display Setting the speaker impedanceMake sure this unit is in the standby mode While holding DownWhen all connections are complete, turn on this unit Turning on this unit and setting it to the standby modeTurning on the power Setting this unit to the standby mode Remote control Front panelPress AMP on the remote control Basic SetupPress Enter to enter Basic Setup Press j / i to select the desired settingPress Enter to confirm your selection 6spkPress SET Menu to exit from Basic Setup Check OK? ..YESTurn on the video monitor connected to this unit Currently selected Input source Input modePlayback Available input sourcesTreble Currently selected sound Field programMuting the audio output Using Other FeaturesUsing Silent Cinema Analog Selecting the input modeDTS Lights up Using the sleep timerFlashes Adjusting the speaker level Selecting the Compressed Music Enhancer mode Enhancer 2CH L RChannel stereo Selecting the Multi CH Input componentEnjoying unprocessed input sources Displaying the input source information Enjoying pure hi-fi stereo soundPlaying video sources in the background Auto Auto Enjoying Surround SoundEnjoying multi-channel sources in surround DecodersEnjoying 2-channel sources in surround PRO LogicUsing Virtual Cinema DSP Recording FM/AM Tuning Automatic tuningAs the input source Press PRESET/TUNING l / h to tune into Press Tuning Mode AUTO/MAN’L so thatAuto indicator disappears from the front Panel displayFM appears in the front panel display Automatic preset tuningPress FM/AM to select FM as the reception band Press and hold Memory MAN’L/AUTO FM for more than 3 secondsSee pages 43 and 44 for tuning instructions Manual preset tuningAutomatic preset tuning options Tune into a station automatically or manuallyRepeat steps 1 through 5 to store other stations Selecting preset stationsPreset station number Displayed station has been stored as C3Press and hold Edit for more than 3 seconds Exchanging preset stationsSee Selecting preset stations on A5FM Press Edit againProgram Radio Data System Tuning Europe Models onlyPress PRESET/CH u / d on the remote Control to select the desired program typeUsing the Radio Data System station network POP MDisplaying the Radio Data System information Frequency display Selecting sound field programs Front panel operations Remote control operationsSound Field Programs Elements of a sound fieldStereo Sound field program descriptionsFor movie/video sources MusicSUR. Standard For music sourcesMovie Theater SUR. EnhancedSettings INIT. DLY Sound field parameter descriptionsDSP Level INIT.DLYRoom Size P.ROOM Size S.ROOM Size SB RM Size Liveness S.LIVENESS SB LivenessREV.DELAY REV.TIMECT Level REV.LEVELDirect SL Level SR LevelCT Width DimensionPanorama ImageSound field program speaker layouts Monaural StereoSUR. Standard Dolby Digital PRO Logic DTS Neo6 Cinema Neo6 MusicChannel audio 6.1-channel audio Monaural Stereo SET Menu CPARAM. INI Adisplay SETBmemory Guard Dmulti ZonePress Enter to enter Manual Setup Using SET MenuPress u / d to select Manual Setup and then press Enter Press AMP and then press SET Menu to enter SET MenuPress i to increase the value Press j to decrease the value Press SET Menu to exit from SET MenuCenter speaker Center Speaker settings Aspeaker SETFront speakers Front Surround left/right speakers SUR. LRLFE/Bass out Bass OUT Subwoofer phase Swfr PhaseSpeaker level B SP Level Crossover CrossoverLow-frequency effect level Elfe Level Speaker distance CSP DistanceCenter graphic equalizer Dcenter GEQ Input assignment Audio settings Gaudio SETDynamic range FD. Range DVD My DVD Speaker B setting SP B Display settings Adisplay SETUse this menu to adjust the optional system parameters Parameter initialization CPARAM. ININame of the selected parameter appears Advanced SetupPress the Program l / h buttons on See page 77 for a complete list of available parametersTuner frequency step TU Asia and General models only Factory presets PresetSpeaker impedance SP IMP Controlling this unit Controlling a TV Remote Control FeaturesControlling this unit, a TV, or other components Controlling other components VCRCategory Setting remote control codesRemote Control Code Default Settings Press STANDBY/ON on the front panel to Resetting the SystemFront panel to select Preset Troubleshooting GeneralSound is heard from Sound suddenlyGoes off Speaker on oneOther settings of this Unit cannot be Changed Or DTS indicatorVolume level Check SP Wires appears in the front panel displayRemote control TunerGlossary Audio informationVideo information Sound field program information Virtual Cinema DSPSpecifications Audio SectionDVD Player All rights reserved

RX-V459 specifications

The Yamaha RX-V459 is a versatile and powerful AV receiver that has become a popular choice among home theater enthusiasts. Known for its impressive features and sound quality, this model stands out in its category, making it an excellent addition to any audio setup.

One of the key features of the RX-V459 is its 7.1-channel surround sound capability. This means it can support up to seven speakers and a subwoofer, ensuring an immersive audio experience. The receiver delivers an impressive power output of 100 watts per channel, which is adequate for filling large rooms with high-quality sound. The RX-V459 also supports various surround sound formats, including Dolby Digital, DTS, and Pro Logic II, providing flexibility for different audio sources.

The RX-V459 includes Yamaha's proprietary YPAO (Yamaha Parametric room Acoustic Optimizer) technology. This innovative feature automatically analyzes your room's acoustics and adjusts the receiver settings for optimal sound performance. By using a provided microphone, YPAO determines the best speaker configuration and calibrates the audio settings accordingly, ensuring a balanced listening experience.

Another notable technology integrated into the RX-V459 is the extensive connectivity options it offers. The receiver is equipped with multiple HDMI inputs, allowing users to connect various devices like Blu-ray players, gaming consoles, and streaming devices easily. Additionally, the RX-V459 supports 1080p video pass-through, ensuring high-definition picture quality for a more enjoyable viewing experience.

Music lovers will appreciate the built-in support for various audio formats, including MP3, WMA, and AAC. The receiver also features a multi-zone functionality, allowing users to enjoy audio in different rooms of the home. This feature enables independent volume and source control, providing flexibility for simultaneous usage.

Furthermore, the RX-V459 incorporates a sleek design that complements modern home entertainment systems. Its clear LCD display and intuitive remote control make operation user-friendly. The receiver also comes with a range of listening modes, allowing users to customize their sound settings to suit different genres of music or movie content.

In conclusion, the Yamaha RX-V459 is an all-around excellent AV receiver that combines power, versatility, and advanced technology. With its capable surround sound processing, room calibration technology, and multiple connectivity options, it’s a solid choice for anyone looking to elevate their home audio and visual experience. Whether for movies, music, or gaming, the RX-V459 provides an enriched atmosphere that appeals to audiophiles and casual listeners alike.
Top Page Image Contents