Yamaha RX-V2500 owner manual Connecting the antennas, Connecting the AM loop antenna

Page 25

Connecting the antennas

Both AM and FM indoor antennas are included with this unit. In general, these antennas should provide sufficient signal strength. Connect each antenna correctly to the designated terminals.

Indoor FM antenna

AM loop antenna

(included)

(included)

TUNER

FM ANT

75Ω

UNBAL.

GND

AM

ANT

COMPONENT VIDEO

Y PB PR

DVD

DTV

CBL/

SAT

MONITOR

OUT

Ground (GND terminal)

For maximum safety and minimum interference, connect the antenna GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth.

■Connecting the AM loop antenna

1Set up the AM loop antenna, then connect it to the terminals on this unit.

2Press and hold the tab to insert the AM loop antenna lead wires into the AM ANT and GND terminals.

CONNECTIONS

3Orient the AM loop antenna for the best reception.

Notes

•The AM loop antenna should be placed away from this unit.

•The AM loop antenna should always be connected, even if an outdoor AM antenna is connected to this unit.

•A property installed outdoor antenna provides clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may improve the quality. Consult the nearest authorized YAMAHA dealer or service center about outdoor antennas.

■75-ohm/300-ohm antenna adapter (U.K. model only)

1Open the cover of the

included 75-ohm/300-ohm antenna adapter.

2Cut the external sleeve

of the 75-ohm coaxial

11 (7/16)

Unit:

8 (5/16)

 

mm (in)

cable and prepare it for 6 (1/14)

connection.

 

 

3 Cut the lead wire and

 

 

remove it.

 

Lead wire

4 Insert the cable

 

 

wire into the slot,

Clamp

Clamp

and clamp it with

 

 

pliers.

 

 

 

Insert the wire

 

 

into the slot

 

5 Snap the cover into place.

PREPARATION

English

23

Page 24 Page 26
Image 25
Page 24 Page 26
Contents RX-V2500 Special Instructions for U.K. Model For U.K. customersContents Built-in 7-channel power amplifier FeaturesSound field features Other featuresInstalling batteries in the remote controls Supplied accessoriesRemote control Getting StartedFront panel Controls and FunctionsOpening and closing the front panel Door Europe models onlyRemote control AMP/SOURCE/TV Multi CHMute ExitHandling the remote control Using the remote controlApproximately 6 m 20 feet Front panel display LFE indicator 96/24 indicatorInput channel indicators Presence and surround back speaker indicatorsAC Inlet Rear panelAC Outlets Speaker placement Speaker SetupDi-pole speaker layout Speaker connections10 mm 3/8 Tighten the knob to secure the wire Connecting to PRESENCE/ZONE 2 or Presence speaker terminalsBanana plug connections Speaker terminal wrench Red positive + Black negativeA. model Right Left Surround speakers Surround back speakers FrontCenter terminals Front terminalsSurround terminals Subwoofer jackCable indications ConnectionsAnalog jacks Digital jacksConnections for DVD playback Connecting video componentsDVD player Video MonitorFor 6-channel input For 8-channel input Connecting to the Multi CH Input jacksMulti-format player External decoder Video AUX jacks on the front panel Connections for other video componentsConnecting a turntable Connecting audio componentsConnections for audio components Connecting to an external amplifier Connecting the AM loop antenna Connecting the antennas75-ohm/300-ohm antenna adapter U.K. model only Connecting the AC power cable Connecting the power cableAsia and General models only Memory back-upTurning on the power Speaker impedance settingPress STANDBY/ON to exit the setting Optimizer microphone setup Auto SetupIntroduction For Wiring, Distance, Size or Level, select Press k / n repeatedly to select Auto Setup, then press hTop display appears SubwooferPress l to move back to Setup Menu Once you have selected the desired settingPress n to select Setup Type, then select For Equalizing, press k / n to selectIf you set Setup Type to Auto If you set Setup Type to StepConfirming the results Before auto setup Troubleshooting for the auto setup procedureDuring auto setup W1Out of Phase After auto setupW3Level Error W2Over DistanceBasic operations PlaybackFront panel operation Selecting sound field programsSelect a sound field program if desired Rotate Program to select the desired programTo adjust the tone Remote control operationTo listen with headphones Additional operationsEnjoying multi-channel software 7.1 channel surround Selecting the Multi CH InputDecoders select with l / h Off OFFWhen you select the SUR. Standard program Press Select on the remote control to select the decoderEnjoying 2-channel software in surround This adjusts the level of compression To cancel, press Pure Direct againListening to high fidelity stereo sound Night listening modesDownmixing to 2 channels Listening to unprocessed input signalsVirtual Cinema DSP Playing video sources BackgroundDisplaying information about the input Source Selecting input modesAutomatic and manual tuning TuningAutomatic tuning Manual tuningAutomatically presetting FM stations Presetting stationsAutomatic preset tuning options Tune into a station Manually presetting stationsPress Memory MAN’L/AUTO FM Repeat steps 1 to 5 to store other stationsExchanging preset stations Selecting preset stationsPress and hold PRESET/TUNING Edit for more than 3 seconds Press PRESET/TUNING Edit againPTY Program Type mode PS Program Service name modeRT Radio Text mode CT Clock Time modeTo exit from the PTY Seek mode, press PTY Seek Mode again Press PTY Seek Mode to set this unit in the PTY Seek modePTY Seek function Selected program type appears on the front panel displayEON function To cancel this functionRecording Special considerations when recording DTS softwareREC OUT For movie/video sources Sound Field Program DescriptionsSources Programs Sound FieldSUR. Standard PRO Logic Music For music sourcesSetting the sleep timer Using the sleep timerCanceling the sleep timer Advanced OperationsSystem Options Manual Setup Manual setupStereo/Surround Stereo/Surround Input Select Input selectAudio Info. Audio signal information Auto Setup Auto setupSystem Memory System memory Option OptionUse the remote control to access and adjust each parameter Changing parameter settingsPress Exit Input Select Volume Trim Volume trimAssignment Input / output assignment Set AMP/SOURCE/TV to AMPRename Rename Press l / h to select OK and press Enter when completeMulti CH Assign Multi channel assignment Input ChannelsLFE Level Low-frequency effect level Manual setup SoundDynamic Range Dynamic range Speaker SpeakerSelect Exit and press Enter to exit the settings window Press h to access the settings windowParametric EQ Parametric equalizer Tone Control Tone controlAudio Option Audio option Audio Delay Audio delayBass Bass control Treble Treble controlSpeaker Set Speaker set Manual setup BasicTest Tone Test tone Front Front speakersSurround Back Surround back left/right speakers Surround Surround left/right speakersChoices Large x1, Small x1, Small Large x2, None Presence Presence speakers Swfr Phase Subwoofer PhaseChoices None, Yes Bass Out Bass outSpeaker Level Speaker level Speaker Distance Speaker distanceUnit Unit Speaker DistancesDisplay Display Manual setup OptionEnter Surr.Initialize Surround initialize Multi Zone Multi zoneTo save settings Input Mode Input modePress Enter to save the settings System MemoryPress Enter to recall the settings To recall settingsLoad Enter appears in the bottom right corner of the window Control area Remote Control FeaturesControlling this unit Controlling other componentsRemote Control Code Default Settings Setting remote control codesControlling optional components Optn area Set AMP/SOURCE/TV to SourceControl See Setting SettingPress Enter Control IDPress Learn again to exit from the setup mode OK appears in the display window if setting was successfulPress Enter to set the number Press an input selector button to select a source componentPress Learn again to exit the learning mode Press Learn using a ballpoint pen or similar objectLearn appears in the display window Display window Changing source namesPress a macro button Using the Macro featureMacro buttons First Second Third Macro operations Press Macro using a ballpoint pen or similar objectProgramming macro operations Set Macro ON/OFF to on Press a macro buttonPress k / n to select the clear mode Press Clear by using a ballpoint pen or similar objectClearing function sets Clear appears in the display windowClearing individual functions Press Clear to exit from the clear modeClearing a learned function Clearing a macro function Press Clear to exit the clearing modePress Learn again to exit Press Macro again to exitVCR Controlling each componentUsing external amplifiers System configuration and connections exampleZone 2/ZONE Zone 2/Zone 3 connectionsTo control Zone 2/Zone To enable Zone mode on the remote ControlSOURCE/REMOTE Turning this unit to either on or standby Press Select k / n to exit from the Zone Zone 3 modeSpecial considerations for DTS software For DVDs encoded with DTSFront Panel Display Menus Advanced setup menuFront panel display system options menu Auto SetupBasic Menu Manual SetupInput Menu Sound MenuCSURR.INI Option MenuResetting parameters to the factory values What is a sound field?Editing Sound Field Parameters Elements of a sound fieldSound Field Parameter Descriptions Init. Delay Initial delayDSP Level DSP level Room Size Room sizeSB Init.Delay Surround back initial delay Sur.Init.Delay Surround initial delayLiveness Liveness Sur.Room Size Surround room sizeRev.Time Reverberation time Rev.Delay Reverberation delayRev.Level Reverberation level Dialogue Lift Dialog lift DimensionFor 7ch Stereo Center WidthFor THX Cinema Decode Type Decoder type For Movie TheaterFor Surround Standard For Surround EnhancedGeneral TroubleshootingGoes off Sound suddenlyOnly the speaker on One side can beVolume level is Or DTS indicator onRecord Volume level Dolby Digital or DTSTuner Does not work nor Remote controlFunction properly Does not learn newAudio formats GlossaryPCM Linear PCM Sound field programsLFE 0.1 channel Audio informationSampling frequency and number Quantized bits THX Cinema processingVideo signal information Frequency Parametric Equalizer InformationFactor GainSpecifications

RX-V2500 specifications

The Yamaha RX-V2500 is a sophisticated audio-video receiver designed for audiophiles and home theater enthusiasts seeking a blend of advanced technology and superior sound quality. Released as part of Yamaha’s acclaimed RX series, the RX-V2500 offers a wealth of features that enhance both music listening and movie watching experiences.

One of the standout features of the RX-V2500 is its power handling capability. With a robust output of 130 watts per channel, this receiver can effortlessly drive a wide range of speakers, ensuring that your audio output is both rich and dynamic. The RX-V2500 supports Dolby Digital EX, DTS-ES, and other multi-channel surround formats, providing an immersive audio experience that brings movies and music to life.

The RX-V2500 also incorporates Yamaha's Cinema DSP technology, which simulates the acoustics of different environments, such as concert halls and theaters. This technology adds depth and realism to sound reproduction, making it feel as though you are part of the action. Additionally, the receiver features multiple listening modes, allowing users to adjust audio settings according to their preferences and the specific content being played.

For connectivity, the RX-V2500 is well-equipped, with a range of inputs and outputs including HDMI ports for high-definition video and audio. This ensures compatibility with a variety of source devices, such as Blu-ray players, gaming consoles, and streaming devices. The receiver also supports HD Radio and is fully compatible with various audio formats, making it an excellent choice for music lovers.

Another notable feature is the YPAO (Yamaha Parametric room Acoustic Optimizer) system. This automatic calibration technology analyzes the room's acoustics and optimizes the receiver's settings to deliver the best possible sound quality based on the environment. It provides a hassle-free setup process, eliminating the guesswork associated with speaker placement and tuning.

The RX-V2500’s user interface is straightforward, making it easy for users to navigate through its numerous features and settings. The remote control is intuitive, allowing convenient access to all functions without needing to physically interact with the receiver.

In terms of build quality, the RX-V2500 is constructed to last, showcasing Yamaha's commitment to durability and performance. This receiver not only offers comprehensive features and advanced technology; it also embodies the brand's dedication to delivering superior sound and movie experiences, making it a worthy investment for any home theater setup.
Top Page Image Contents