Yamaha RX-V2500 Multi CH, Amp/Source/Tv, Mute, Exit, Night, Display, Extd. Sur, Re-Name, Clear

Page 9

IMULTI CH IN

Selects MULTI CH INPUT when using an external decoder (etc.).

JSELECT k / n

Selects another component that you can control independently of the input component selected with the input selector buttons.

KVOL +/–

Increases or decreases the volume level.

LAMP/SOURCE/TV

Selects the component you want to control with the remote control.

AMP: Set to this position to operate this unit.

SOURCE: Set to this position to operate the component selected with an input selector button.

TV: Set to this position to operate the television. To set the remote control codes for components, see page 70.

MMUTE

Mutes the sound. Press again to restore the audio output to the previous volume level.

NPURE DIRECT

Turns on or off PURE DIRECT mode (see page 37).

OEXIT

Use to exit the graphical user interface (GUI) mode.

PNIGHT

Turns on or off the night listening modes (see page 37).

QDISPLAY

Use to enter into the front panel display menu mode.

RSTRAIGHT/EFFECT

Switches the sound fields off or on. When STRAIGHT is selected, input signals (2-channel or multi-channel) are output directly from their respective speakers without effect processing.

SEXTD. SUR

Switches between 5.1 or 6.1/7.1 channel playback of multi-channel software.

TSPEAKERS A/B

Turn on or off the set of front speakers connected to the A and/or B terminals on the rear panel at each time the corresponding button is pressed.

URE-NAME

Used to change the input source name in the display window (see page 74).

VCLEAR

Used to clear functions acquired when using the learn, macro and rename features, or setting remote control codes (see page 77).

CONTROLS AND FUNCTIONS

WLEARN

Used to set up the remote control code or program functions from other remote controls (see page 72).

■U.K. and Europe models only

XRDS tuning buttons

(Available when this unit is in tuner mode)

FREQ/RDS

Press this button when the unit is receiving an RDS station to cycle the display between the PS mode, PTY mode, RT mode, CT mode (if the station offers those RDS data services) and/or the frequency display (see page 44).

EON

Press this button to select a radio program type (NEWS, INFO, AFFAIRS, SPORT) to tune in automatically (see page 46).

PTY SEEK MODE

Press this button to set the unit to the PTY SEEK mode (see page 45).

PTY SEEK START

Press this button to begin searching for a station after the desired program type has been selected in the PTY SEEK mode (see page 45).

INTRODUCTION

English

7

Page 8 Page 10
Image 9
Page 8 Page 10
Contents RX-V2500 Special Instructions for U.K. Model For U.K. customersContents Built-in 7-channel power amplifier FeaturesSound field features Other featuresInstalling batteries in the remote controls Supplied accessoriesRemote control Getting StartedFront panel Controls and FunctionsOpening and closing the front panel Door Europe models onlyRemote control AMP/SOURCE/TV Multi CHMute ExitUsing the remote control Handling the remote controlApproximately 6 m 20 feet Front panel display LFE indicator 96/24 indicatorInput channel indicators Presence and surround back speaker indicatorsRear panel AC InletAC Outlets Speaker placement Speaker SetupSpeaker connections Di-pole speaker layout10 mm 3/8 Tighten the knob to secure the wire Connecting to PRESENCE/ZONE 2 or Presence speaker terminalsBanana plug connections Speaker terminal wrench Red positive + Black negativeA. model Right Left Surround speakers Surround back speakers FrontCenter terminals Front terminalsSurround terminals Subwoofer jackCable indications ConnectionsAnalog jacks Digital jacksConnections for DVD playback Connecting video componentsDVD player Video MonitorConnecting to the Multi CH Input jacks For 6-channel input For 8-channel inputMulti-format player External decoder Video AUX jacks on the front panel Connections for other video componentsConnecting audio components Connecting a turntableConnections for audio components Connecting to an external amplifier Connecting the antennas Connecting the AM loop antenna75-ohm/300-ohm antenna adapter U.K. model only Connecting the AC power cable Connecting the power cableAsia and General models only Memory back-upSpeaker impedance setting Turning on the powerPress STANDBY/ON to exit the setting Auto Setup Optimizer microphone setupIntroduction For Wiring, Distance, Size or Level, select Press k / n repeatedly to select Auto Setup, then press hTop display appears SubwooferPress l to move back to Setup Menu Once you have selected the desired settingPress n to select Setup Type, then select For Equalizing, press k / n to selectIf you set Setup Type to Step If you set Setup Type to AutoConfirming the results Troubleshooting for the auto setup procedure Before auto setupDuring auto setup W1Out of Phase After auto setupW3Level Error W2Over DistanceBasic operations PlaybackFront panel operation Selecting sound field programsSelect a sound field program if desired Rotate Program to select the desired programTo adjust the tone Remote control operationTo listen with headphones Additional operationsEnjoying multi-channel software 7.1 channel surround Selecting the Multi CH InputDecoders select with l / h Off OFFPress Select on the remote control to select the decoder When you select the SUR. Standard programEnjoying 2-channel software in surround This adjusts the level of compression To cancel, press Pure Direct againListening to high fidelity stereo sound Night listening modesDownmixing to 2 channels Listening to unprocessed input signalsVirtual Cinema DSP Playing video sources BackgroundDisplaying information about the input Source Selecting input modesAutomatic and manual tuning TuningAutomatic tuning Manual tuningPresetting stations Automatically presetting FM stationsAutomatic preset tuning options Tune into a station Manually presetting stationsPress Memory MAN’L/AUTO FM Repeat steps 1 to 5 to store other stationsExchanging preset stations Selecting preset stationsPress and hold PRESET/TUNING Edit for more than 3 seconds Press PRESET/TUNING Edit againPTY Program Type mode PS Program Service name modeRT Radio Text mode CT Clock Time modeTo exit from the PTY Seek mode, press PTY Seek Mode again Press PTY Seek Mode to set this unit in the PTY Seek modePTY Seek function Selected program type appears on the front panel displayEON function To cancel this functionSpecial considerations when recording DTS software RecordingREC OUT For movie/video sources Sound Field Program DescriptionsSources Programs Sound FieldSUR. Standard PRO Logic Music For music sourcesSetting the sleep timer Using the sleep timerCanceling the sleep timer Advanced OperationsSystem Options Manual Setup Manual setupStereo/Surround Stereo/Surround Input Select Input selectAudio Info. Audio signal information Auto Setup Auto setupSystem Memory System memory Option OptionChanging parameter settings Use the remote control to access and adjust each parameterPress Exit Input Select Volume Trim Volume trimAssignment Input / output assignment Set AMP/SOURCE/TV to AMPRename Rename Press l / h to select OK and press Enter when completeMulti CH Assign Multi channel assignment Input ChannelsLFE Level Low-frequency effect level Manual setup SoundDynamic Range Dynamic range Speaker SpeakerSelect Exit and press Enter to exit the settings window Press h to access the settings windowParametric EQ Parametric equalizer Tone Control Tone controlAudio Option Audio option Audio Delay Audio delayBass Bass control Treble Treble controlSpeaker Set Speaker set Manual setup BasicTest Tone Test tone Front Front speakersSurround Surround left/right speakers Surround Back Surround back left/right speakersChoices Large x1, Small x1, Small Large x2, None Presence Presence speakers Swfr Phase Subwoofer PhaseChoices None, Yes Bass Out Bass outSpeaker Level Speaker level Speaker Distance Speaker distanceUnit Unit Speaker DistancesManual setup Option Display DisplayEnter Surr.Initialize Surround initialize Multi Zone Multi zoneTo save settings Input Mode Input modePress Enter to save the settings System MemoryTo recall settings Press Enter to recall the settingsLoad Enter appears in the bottom right corner of the window Control area Remote Control FeaturesControlling this unit Controlling other componentsRemote Control Code Default Settings Setting remote control codesControlling optional components Optn area Set AMP/SOURCE/TV to SourceControl See Setting SettingPress Enter Control IDPress Learn again to exit from the setup mode OK appears in the display window if setting was successfulPress Enter to set the number Press an input selector button to select a source componentPress Learn using a ballpoint pen or similar object Press Learn again to exit the learning modeLearn appears in the display window Display window Changing source namesUsing the Macro feature Press a macro buttonMacro buttons First Second Third Macro operations Press Macro using a ballpoint pen or similar objectProgramming macro operations Set Macro ON/OFF to on Press a macro buttonPress k / n to select the clear mode Press Clear by using a ballpoint pen or similar objectClearing function sets Clear appears in the display windowPress Clear to exit from the clear mode Clearing individual functionsClearing a learned function Clearing a macro function Press Clear to exit the clearing modePress Learn again to exit Press Macro again to exitVCR Controlling each componentUsing external amplifiers System configuration and connections exampleZone 2/ZONE Zone 2/Zone 3 connectionsTo enable Zone mode on the remote Control To control Zone 2/ZoneSOURCE/REMOTE Turning this unit to either on or standby Press Select k / n to exit from the Zone Zone 3 modeSpecial considerations for DTS software For DVDs encoded with DTSFront Panel Display Menus Advanced setup menuFront panel display system options menu Auto SetupBasic Menu Manual SetupInput Menu Sound MenuCSURR.INI Option MenuResetting parameters to the factory values What is a sound field?Editing Sound Field Parameters Elements of a sound fieldSound Field Parameter Descriptions Init. Delay Initial delayDSP Level DSP level Room Size Room sizeSB Init.Delay Surround back initial delay Sur.Init.Delay Surround initial delayLiveness Liveness Sur.Room Size Surround room sizeRev.Delay Reverberation delay Rev.Time Reverberation timeRev.Level Reverberation level Dialogue Lift Dialog lift DimensionFor 7ch Stereo Center WidthFor THX Cinema Decode Type Decoder type For Movie TheaterFor Surround Standard For Surround EnhancedGeneral TroubleshootingGoes off Sound suddenlyOnly the speaker on One side can beVolume level is Or DTS indicator onRecord Volume level Dolby Digital or DTSTuner Does not work nor Remote controlFunction properly Does not learn newAudio formats GlossaryPCM Linear PCM Sound field programsLFE 0.1 channel Audio informationSampling frequency and number Quantized bits THX Cinema processingVideo signal information Frequency Parametric Equalizer InformationFactor GainSpecifications

RX-V2500 specifications

The Yamaha RX-V2500 is a sophisticated audio-video receiver designed for audiophiles and home theater enthusiasts seeking a blend of advanced technology and superior sound quality. Released as part of Yamaha’s acclaimed RX series, the RX-V2500 offers a wealth of features that enhance both music listening and movie watching experiences.

One of the standout features of the RX-V2500 is its power handling capability. With a robust output of 130 watts per channel, this receiver can effortlessly drive a wide range of speakers, ensuring that your audio output is both rich and dynamic. The RX-V2500 supports Dolby Digital EX, DTS-ES, and other multi-channel surround formats, providing an immersive audio experience that brings movies and music to life.

The RX-V2500 also incorporates Yamaha's Cinema DSP technology, which simulates the acoustics of different environments, such as concert halls and theaters. This technology adds depth and realism to sound reproduction, making it feel as though you are part of the action. Additionally, the receiver features multiple listening modes, allowing users to adjust audio settings according to their preferences and the specific content being played.

For connectivity, the RX-V2500 is well-equipped, with a range of inputs and outputs including HDMI ports for high-definition video and audio. This ensures compatibility with a variety of source devices, such as Blu-ray players, gaming consoles, and streaming devices. The receiver also supports HD Radio and is fully compatible with various audio formats, making it an excellent choice for music lovers.

Another notable feature is the YPAO (Yamaha Parametric room Acoustic Optimizer) system. This automatic calibration technology analyzes the room's acoustics and optimizes the receiver's settings to deliver the best possible sound quality based on the environment. It provides a hassle-free setup process, eliminating the guesswork associated with speaker placement and tuning.

The RX-V2500’s user interface is straightforward, making it easy for users to navigate through its numerous features and settings. The remote control is intuitive, allowing convenient access to all functions without needing to physically interact with the receiver.

In terms of build quality, the RX-V2500 is constructed to last, showcasing Yamaha's commitment to durability and performance. This receiver not only offers comprehensive features and advanced technology; it also embodies the brand's dedication to delivering superior sound and movie experiences, making it a worthy investment for any home theater setup.
Top Page Image Contents