Yamaha RX-V2500 owner manual Manual setup Option, Display Display, Enter

Page 67

Manual setup: Option

This menu adjusts the optional system settings.

1Set AMP/SOURCE/TV to AMP.

AMP

SOURCE

TV

2Press TOP on the remote control.

3Select Manual Setup, then press h.

4Select Option then press h.

Sound

Display

Basic

Multi Zone

Option

Surr.Initialize

 

Input Mode

 

Memory Guard

5Select the desired parameters, then press h to access and adjust.

6When finished adjusting parameters, press

ENTER.

■Display (Display)

Use this feature to adjust the GUI and front panel displays.

Manual Setup > Option > Display >

 

Dimmer

 

Video Conv.

Display

Short Message

Multi Zone

Position

Surr.Initialize

Wall Paper

Dimmer (Dimmer)

Use to adjust the brightness of the front panel display. Choices: –4 to 0

SYSTEM OPTIONS

Video Conv. (Video conversion)

Use this feature to turn on/off conversion of composite (VIDEO) signals to both S-video and component signals. This allows you to output converted video signals from the S VIDEO or COMPONENT VIDEO jacks when no S-video or component signals are input. This feature also converts S-video signals to component signals when no component signals are input.

Choices: Off, On

•Select “Off” not to convert any signals.

•Select “On” to convert composite signals to S-video and component signals, and to convert S-video signals to component signals.

y

When using the THX system, we recommend setting Video Conv. to “Off”.

Notes

•Converted video signals are only output to the MONITOR OUT jacks. When recording you must make the same type of video connections (composite or S-video) between each component.

•When converting composite video or S-video signals from a VCR to component video signals, the picture quality may suffer depending on your VCR.

Short Message (Short message)

Use this feature to turn on/off the short message display. Choices: Off, On

•Select “Off” to turn off the short message display.

•Select “On” to turn on the short message display.

Notes

•The short message display may not display properly depending on the type of input signal and video monitor used.

•If Video Conv. is set to “Off”, the short message display is not displayed even if “On” is selected.

Position (Position)

Use to adjust the vertical and horizontal position of the GUI display.

Choices: –5 (downward/left) to +5 (upward/right)

•Press k to raise the position of the GUI display.

•Press n to lower the position of the GUI display.

•Press h to shift the position of the GUI display to the right.

•Press lto shift the position of the GUI display to the left.

Wall Paper (Wallpaper)

Use this feature to select the background when no image is input from an external source. If you do not want to display the background, select None.

Choices: None, Yes, Gray Back

Note

If Video Conv. is set to “Off”, no background is displayed even if “Yes” is selected.

y

This menu item is also available in the front panel display system options menu (see page 85).

OPERATION

ADVANCED

 

 

English

65

Page 66 Page 68
Image 67
Page 66 Page 68
Contents RX-V2500 Special Instructions for U.K. Model For U.K. customersContents Other features FeaturesBuilt-in 7-channel power amplifier Sound field featuresGetting Started Supplied accessoriesInstalling batteries in the remote controls Remote controlFront panel Controls and FunctionsOpening and closing the front panel Door Europe models onlyRemote control Exit Multi CHAMP/SOURCE/TV MuteHandling the remote control Using the remote controlApproximately 6 m 20 feet Front panel display Presence and surround back speaker indicators 96/24 indicatorLFE indicator Input channel indicatorsAC Inlet Rear panelAC Outlets Speaker placement Speaker SetupDi-pole speaker layout Speaker connections10 mm 3/8 Speaker terminal wrench Red positive + Black negative Connecting to PRESENCE/ZONE 2 or Presence speaker terminalsTighten the knob to secure the wire Banana plug connectionsA. model Right Left Surround speakers Surround back speakers FrontSubwoofer jack Front terminalsCenter terminals Surround terminalsDigital jacks ConnectionsCable indications Analog jacksVideo Monitor Connecting video componentsConnections for DVD playback DVD playerFor 6-channel input For 8-channel input Connecting to the Multi CH Input jacksMulti-format player External decoder Video AUX jacks on the front panel Connections for other video componentsConnecting a turntable Connecting audio componentsConnections for audio components Connecting to an external amplifier Connecting the AM loop antenna Connecting the antennas75-ohm/300-ohm antenna adapter U.K. model only Memory back-up Connecting the power cableConnecting the AC power cable Asia and General models onlyTurning on the power Speaker impedance settingPress STANDBY/ON to exit the setting Optimizer microphone setup Auto SetupIntroduction Subwoofer Press k / n repeatedly to select Auto Setup, then press hFor Wiring, Distance, Size or Level, select Top display appearsFor Equalizing, press k / n to select Once you have selected the desired settingPress l to move back to Setup Menu Press n to select Setup Type, then selectIf you set Setup Type to Auto If you set Setup Type to StepConfirming the results Before auto setup Troubleshooting for the auto setup procedureDuring auto setup W2Over Distance After auto setupW1Out of Phase W3Level ErrorBasic operations PlaybackRotate Program to select the desired program Selecting sound field programsFront panel operation Select a sound field program if desiredAdditional operations Remote control operationTo adjust the tone To listen with headphonesOff OFF Selecting the Multi CH InputEnjoying multi-channel software 7.1 channel surround Decoders select with l / hWhen you select the SUR. Standard program Press Select on the remote control to select the decoderEnjoying 2-channel software in surround Night listening modes To cancel, press Pure Direct againThis adjusts the level of compression Listening to high fidelity stereo soundPlaying video sources Background Listening to unprocessed input signalsDownmixing to 2 channels Virtual Cinema DSPDisplaying information about the input Source Selecting input modesManual tuning TuningAutomatic and manual tuning Automatic tuningAutomatically presetting FM stations Presetting stationsAutomatic preset tuning options Repeat steps 1 to 5 to store other stations Manually presetting stationsTune into a station Press Memory MAN’L/AUTO FMPress PRESET/TUNING Edit again Selecting preset stationsExchanging preset stations Press and hold PRESET/TUNING Edit for more than 3 secondsCT Clock Time mode PS Program Service name modePTY Program Type mode RT Radio Text modeSelected program type appears on the front panel display Press PTY Seek Mode to set this unit in the PTY Seek modeTo exit from the PTY Seek mode, press PTY Seek Mode again PTY Seek functionEON function To cancel this functionRecording Special considerations when recording DTS softwareREC OUT For movie/video sources Sound Field Program DescriptionsSources Programs Sound FieldSUR. Standard PRO Logic Music For music sourcesAdvanced Operations Using the sleep timerSetting the sleep timer Canceling the sleep timerInput Select Input select Manual Setup Manual setupSystem Options Stereo/Surround Stereo/SurroundOption Option Auto Setup Auto setupAudio Info. Audio signal information System Memory System memoryUse the remote control to access and adjust each parameter Changing parameter settingsPress Exit Set AMP/SOURCE/TV to AMP Volume Trim Volume trimInput Select Assignment Input / output assignmentInput Channels Press l / h to select OK and press Enter when completeRename Rename Multi CH Assign Multi channel assignmentSpeaker Speaker Manual setup SoundLFE Level Low-frequency effect level Dynamic Range Dynamic rangeTone Control Tone control Press h to access the settings windowSelect Exit and press Enter to exit the settings window Parametric EQ Parametric equalizerTreble Treble control Audio Delay Audio delayAudio Option Audio option Bass Bass controlFront Front speakers Manual setup BasicSpeaker Set Speaker set Test Tone Test toneSurround Back Surround back left/right speakers Surround Surround left/right speakersChoices Large x1, Small x1, Small Large x2, None Bass Out Bass out Swfr Phase Subwoofer PhasePresence Presence speakers Choices None, YesSpeaker Distances Speaker Distance Speaker distanceSpeaker Level Speaker level Unit UnitDisplay Display Manual setup OptionEnter Surr.Initialize Surround initialize Multi Zone Multi zoneSystem Memory Input Mode Input modeTo save settings Press Enter to save the settingsPress Enter to recall the settings To recall settingsLoad Enter appears in the bottom right corner of the window Controlling other components Remote Control FeaturesControl area Controlling this unitSet AMP/SOURCE/TV to Source Setting remote control codesRemote Control Code Default Settings Controlling optional components Optn areaControl ID SettingControl See Setting Press EnterPress an input selector button to select a source component OK appears in the display window if setting was successfulPress Learn again to exit from the setup mode Press Enter to set the numberPress Learn again to exit the learning mode Press Learn using a ballpoint pen or similar objectLearn appears in the display window Display window Changing source namesPress a macro button Using the Macro featureMacro buttons First Second Third Set Macro ON/OFF to on Press a macro button Press Macro using a ballpoint pen or similar objectMacro operations Programming macro operationsClear appears in the display window Press Clear by using a ballpoint pen or similar objectPress k / n to select the clear mode Clearing function setsClearing individual functions Press Clear to exit from the clear modeClearing a learned function Press Macro again to exit Press Clear to exit the clearing modeClearing a macro function Press Learn again to exitVCR Controlling each componentZone 2/Zone 3 connections System configuration and connections exampleUsing external amplifiers Zone 2/ZONETo control Zone 2/Zone To enable Zone mode on the remote ControlSOURCE/REMOTE For DVDs encoded with DTS Press Select k / n to exit from the Zone Zone 3 modeTurning this unit to either on or standby Special considerations for DTS softwareFront Panel Display Menus Advanced setup menuFront panel display system options menu Auto SetupBasic Menu Manual SetupInput Menu Sound MenuCSURR.INI Option MenuElements of a sound field What is a sound field?Resetting parameters to the factory values Editing Sound Field ParametersRoom Size Room size Init. Delay Initial delaySound Field Parameter Descriptions DSP Level DSP levelSur.Room Size Surround room size Sur.Init.Delay Surround initial delaySB Init.Delay Surround back initial delay Liveness LivenessRev.Time Reverberation time Rev.Delay Reverberation delayRev.Level Reverberation level Center Width DimensionDialogue Lift Dialog lift For 7ch StereoFor Surround Enhanced Decode Type Decoder type For Movie TheaterFor THX Cinema For Surround StandardGeneral TroubleshootingOne side can be Sound suddenlyGoes off Only the speaker onDolby Digital or DTS Or DTS indicator onVolume level is Record Volume levelTuner Does not learn new Remote controlDoes not work nor Function properlyAudio formats GlossaryPCM Linear PCM Sound field programsTHX Cinema processing Audio informationLFE 0.1 channel Sampling frequency and number Quantized bitsVideo signal information Gain Parametric Equalizer InformationFrequency FactorSpecifications

RX-V2500 specifications

The Yamaha RX-V2500 is a sophisticated audio-video receiver designed for audiophiles and home theater enthusiasts seeking a blend of advanced technology and superior sound quality. Released as part of Yamaha’s acclaimed RX series, the RX-V2500 offers a wealth of features that enhance both music listening and movie watching experiences.

One of the standout features of the RX-V2500 is its power handling capability. With a robust output of 130 watts per channel, this receiver can effortlessly drive a wide range of speakers, ensuring that your audio output is both rich and dynamic. The RX-V2500 supports Dolby Digital EX, DTS-ES, and other multi-channel surround formats, providing an immersive audio experience that brings movies and music to life.

The RX-V2500 also incorporates Yamaha's Cinema DSP technology, which simulates the acoustics of different environments, such as concert halls and theaters. This technology adds depth and realism to sound reproduction, making it feel as though you are part of the action. Additionally, the receiver features multiple listening modes, allowing users to adjust audio settings according to their preferences and the specific content being played.

For connectivity, the RX-V2500 is well-equipped, with a range of inputs and outputs including HDMI ports for high-definition video and audio. This ensures compatibility with a variety of source devices, such as Blu-ray players, gaming consoles, and streaming devices. The receiver also supports HD Radio and is fully compatible with various audio formats, making it an excellent choice for music lovers.

Another notable feature is the YPAO (Yamaha Parametric room Acoustic Optimizer) system. This automatic calibration technology analyzes the room's acoustics and optimizes the receiver's settings to deliver the best possible sound quality based on the environment. It provides a hassle-free setup process, eliminating the guesswork associated with speaker placement and tuning.

The RX-V2500’s user interface is straightforward, making it easy for users to navigate through its numerous features and settings. The remote control is intuitive, allowing convenient access to all functions without needing to physically interact with the receiver.

In terms of build quality, the RX-V2500 is constructed to last, showcasing Yamaha's commitment to durability and performance. This receiver not only offers comprehensive features and advanced technology; it also embodies the brand's dedication to delivering superior sound and movie experiences, making it a worthy investment for any home theater setup.
Top Page Image Contents