Yamaha RX-396RDS/396 Antenna Connections, English, ➀ ➂ ➁, Connecting the AM loop antenna

Page 9

ANTENNA CONNECTIONS

ANTENNA CONNECTIONS

●Each antenna should be connected to the designated terminal(s) correctly, referring to the following diagram.

●Both AM and FM indoor antennas are supplied to this unit. In general, these antennas will provide sufficient signal strength. Nevertheless, a properly installed outdoor antenna will give clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may result in improvement.

Outdoor FM antenna			Outdoor AM antenna

Indoor FM antenna (included)

English

75-ohm/300-ohm antenna adapter

75-ohm coaxial cable

75-ohm/300-ohm antenna adapter

300-ohm feeder

75Ω

UNBAL.

FM

ANT

GND

AM

ANT

AM loop antenna (included)

Ground

Connecting the AM loop antenna

1

2

3

➀

➂

➁

Orient so that the best reception is obtained.

*The AM loop antenna should be placed apart from the main unit. The antenna may be hung on a wall.

*The AM loop antenna should be kept connected, even if an outdoor AM antenna is connected to this unit.

GND terminal

For maximum safety and minimum interference, connect the GND terminal to a good earth ground, which is a metal stake driven into moist earth.

Notes

●When connecting the indoor FM antenna, insert its connector into the FM ANT

terminal firmly.

●If you need an outdoor

FM antenna to improve FM reception quality, either

300-ohm feeder or coaxial cable may be used. In locations troubled by electrical interference, a coaxial cable is preferable.

9

Image 9

Contents RX-496RDS/496 RX-396RDS/396 MANUAL DE INSTRUCCIONES GEBRUIKSAANWIJZINGNatural Sound Stereo Receiver Récepteur stéréo Natural Sound StereoreceiverIndoor FM Antenna Antenne FM intérieure CONTENTS FEATURESEnglish RX-496RDSand RX-496For U.K. customers CAUTION READ THIS BEFORE OPERATING YOUR UNITSpecial Instructions for U.K. Model 13.Voltage Selector General Model onlyBattery installation NOTES ABOUT THE REMOTE CONTROL TRANSMITTERRemote control transmitter operation range Battery replacementCONNECTIONS WITH OTHER COMPONENTS CONNECTIONSU.S.A. model AC* OUTLETS SWITCHED CONNECTING SPEAKERSHow to Connect GND* terminal For turntable useIMPEDANCE SELECTOR IMPEDANCE SELECTOR switchFor U.S.A. model only For Canada model onlyConnecting the AM loop antenna ANTENNA CONNECTIONSEnglish ➀ ➂ ➁RX-496RDSand RX-496 CONTROLS AND THEIR FUNCTIONSC DEFG IJ L RX-396RDSand RX-3962Remote control sensor 1STANDBY/ON switch6VOLUME control 8SPEAKERS switchesFor Control of This Unit REMOTE CONTROL TRANSMITTERFor Other Component Control 2SLEEP timer keyPage When you finish using this unit BASIC OPERATIONSNotes on using the input selector buttons RX-496RDSand RX-496onlyVOLUME, BASS, TREBLE, BALANCE and LOUDNESS TO RECORD OR DUB A SOURCE TO TAPE OR MDEnglish Adjusting the BASS and TREBLE controls Adjusting the BALANCE controlUsing the PURE DIRECT switch Selecting the SPEAKER systemTUNING OPERATIONS EnglishRX-496RDSand RX-396RDSonly MANUAL PRESET TUNING PRESET TUNINGTo recall a preset station To store stationsDOWN TUNING UP AUTOMATIC PRESET TUNINGRX-496RDSand RX-396RDSonly FM/AMWhen the automatic preset tuning is finished EXCHANGING PRESET STATIONSTo recall a preset station RX-496RDS, RX-396RDSRECEIVING RDS STATIONS PS Program Service name modeRX-496RDSand RX-396RDSonly Displaying RDS dataNEWS News Program types in the PTY modeSPORT Sport DRAMA DramaEnglish Changing the RDS modesTo cancel this function To cancel this function EnglishPress once TROUBLESHOOTING Page Page YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A