Speco Technologies SIPT5, SIPSD10X instruction manual MPEG4

Page 33

RTP B2 Frame

Checkbox to enable the B2 frame in RTP streaming

Enable

 

 

Audio

Select enable or disable the audio function.

Input Sensitivity

Select HIGH or LOW of the audio input sensitivity

Multicast IP

Select the multicast IP. Default settings is 228.5.6.1

Multicast TTL

Select the multicast TTL. Default setting is 255.

 

Select video type connected to the video-in of this IP

IGMP

device. If you use an incorrect video type, some images

 

might be lost.

Resolution

Select the video resolution of the IP device.

 

Select the frame rate mode.

 

Constant: The streaming’s frame rate remains

Frame rate mode

 

constant at all conditions.

Variable: The streaming’s frame rate will variants

 

 

 

according to the images variability to keep the

 

 

image quality good.

Frame rate

Select the frame rate of the video streaming.

 

Select the encoder’s compression type.

Encoder Type

1.

MPEG4

 

2.

MJPEG

 

Select the video bitrate mode.

Video Bitrate

Constant Bit Rate: The streaming’s bitrate remains

constant at all conditions.

Mode

Variable Bit Rate: The streaming’s bitrate will

 

variants according to the images variability to keep the

 

image quality good.

Video Maximum

Select the Maximum bitrate of the video straming.

Designating a limited bit rate may reduce frame

Bitrate

rate. Doing so will also disable Bit Rate setting below.

 

 

Select the bit rate of the video streaming. You can select

 

from 28Kbps to 3Mbps.

Bitrate

Note: Lower bit rate consumes less bandwidth but

delivers lower quality images.

 

 

High bit rate consumes more bandwidth but delivers

 

higher quality images.

Serial Port Baud

Select the Baud Rate setting of serial port.

Rate

 

 

Serial Port Control

Select the Control setting of serial port.

RTSP port

Select the port for this IP device to support RTSP

Video RTP Over

Enable/disable the multicast video streaming via RTP

Multicast

protocol

 

Audio RTP Over

Enable/disable the multicast audio streaming via RTP

Multicast

protocol

 

Video control port

Select the port for this IP device to support video control

function of the application program.

Video streaming

Select the port for this IP device to support video

port (TCP Only)

streaming function of the application program.

Video multicast

Select the port for this IP device to support video multicast

port (Multicast

function of the application program.

2-29

Image 33
Contents Speco Internet Protocol SIP Series Table of Contents Appendix Page Features Dimensions Dimension and Connector DescriptionSIPD3 SIPD4 SIPT5 SIPSD10X Sipmpb Sipmpd ① 12 Volts DC Power Input ② Audio Output Connector Description⑧ OSD control joystick Installation Setup your PC network Preparation before setupStep Double-click the Network and Internet connections icon Step Click the OK button and the window dialog box closes Configuring the IP device Page Video Display Page Host Setting Host Setting100Mbps / Full duplex WAN Setting WAN Setting Page SNTP/NTP Date SettingManually set date and time will be gone, if power off Video setting Video SettingMPEG4 Only Video Adjustment Page Camera setting Camera SetupOUTDOOR1 Select the outdoor white balance BLC Camera Setup PTZ camera modelSelect exposure mode PTZ PT/TZ Camera only Page User Account Management System info System InfoPage Firmware Upgrade You can always get the latest version at our website Factory Default Save Reboot Logout Function OSD SettingF T Down Setup OSD Menu SettingOperating Camera OSD Menu Page Brightness Page Page Page OFF / LOW / Middle / High OFF / on Auto Gain Control AGCWhite Balance Wite BAL Page When selected ‘GAIN’ menu OFF, DNR will not work Intensifier Next Camera Title Page Camera Title Sync Privacy Reverse Detail Default Operating Camera OSD Menu SIPSD10X only Dome SET Recover Default SettingDome SET Camera ID Dome SET Manual SpeedDome SET Next page Password Dome SET AlarmDome SET Zoom Speed Dome SET LanguageDome SET Next page OSD Display Enter Password By Entering Preset Code ConfirmDome SET Next page Initialization Dome SET Next page System StatusTour Clear Are YOU SURE? YES no Dome SET Next page Exit Dome SET Next page Save and ExitCamera SET Camera SET FlickerlessCamera SET D/N Mode Camera SET WB ModeCamera SET DSS Mode Digital Slow Shutter Camera SET D ZoomPreset Preset no Preset SETPreset Preset ID Preset PAN XXX.X TiltPreset Exit Preset SaveAuto Scan SET Auto SCAN- Start AngleAuto Scan Speed Auto Scan EndlessAuto Scan Dwell Time Auto Scan Save and ExitTour SET Tour SET Preset noTour SET Tour no Tour SET Tour TitleTour SET Save Tour SET SpeedTour SET Exit Privacy SETPrivacy SET Save Privacy SET ACTIONMOVE/ADJUSTPrivacy SET Exit Pattern SETPattern SET Patt Title Pattern SET Patt noPattern SET Data Fill Pattern SET SaveAlaram SET Alarm no Alarm SETAlaram SET Alarm Input Alaram SET Alarm ACTSector SET Default Setting Sector SET Sector noSector SET Sector ID Sector SET Sector StartSector SET Save Sector SET ExitExit ID Setting SIPSD10X only DIP SW Setting SIPSD10X onlyProtocol SIPSD10X only Baud Rate Setting SIPSD10X onlySIP Camera Series AppendixCamera Spec SIPB2 SIPD3 SIPD4 SIPT5 BLC On / OFF DNS, DDNS, NTP, ICMP, IGMP, ARP, #GPP Sipmp Camera SeriesCamera Spec Sipmpd SIPMPT5

SIPSD10X, SIPT5 specifications

Speco Technologies is a well-known provider of innovative and high-quality security solutions, and their SIPT5 and SIPSD10X models epitomize their commitment to excellence. Both products are designed to cater to a range of surveillance applications, making them pivotal in enhancing security measures for residential and commercial purposes.

The Speco Technologies SIPT5 is an advanced intercom system that is particularly known for its two-way audio and video capabilities. With its user-friendly interface, it offers seamless communication and monitoring. The SIPT5 employs IP technology, allowing for integration with existing security networks. One of its standout features is the high-definition video camera, which provides clear and crisp images, ensuring that users can identify visitors with utmost clarity. The device supports PoE (Power over Ethernet), enabling simplified installation by supplying power and data through a single cable. Additionally, the SIPT5’s versatility is reflected in its compatibility with various mobile devices, allowing users to monitor their surroundings remotely through secure applications.

On the other hand, the SIPSD10X is an exceptional outdoor-rated speaker designed to be paired with the SIPT5 system. This speaker features a robust construction that withstands various environmental conditions, making it ideal for outdoor installations. One of the main characteristics of the SIPSD10X is its high sound output, which ensures that audio signals are effectively transmitted, even in noisy environments. It integrates perfectly with the SIPT5, allowing for clear audio communication, whether users are outdoors or indoors. The speaker also supports a wide frequency response, which enhances the quality of sound reproduction during intercom conversations.

Both the SIPT5 and SIPSD10X leverage advanced digital signal processing technology to minimize noise and enhance audio clarity. They are also equipped with secure encryption protocols, ensuring that all data transmission is safe from unauthorized access. Together, these products create a robust intercom system that not only enhances communication but also elevates security monitoring capabilities.

In conclusion, Speco Technologies' SIPT5 and SIPSD10X represent a significant advancement in intercom and speaker technology, combining high-definition video, robust audio performance, and the reliability of IP infrastructure, making them essential components for effective security solutions. Whether for residential use or in commercial settings, these products provide a seamless, efficient, and secure user experience essential for modern security requirements.