Yamaha HTR-5760 owner manual Sound suddenly, Goes off, Only the speaker on, One side can be, Heard

Page 75

TROUBLESHOOTING

Problem

Cause

Remedy

Refer to

page

 

 

 

 

 

 

 

The sound suddenly

The protection circuitry has been activated

Check that the impedance selector setting is correct.

23

goes off.

because of a short circuit, etc.

 

 

Check that the speaker wires are not touching each

—

 

 

 

 

other and then turn this unit back on.

 

 

 

 

 

 

The sleep timer has turned the unit off.

Turn on the power, and play the source again.

—

 

 

 

 

 

The sound is muted.

Press MUTE to cancel a mute.

31

 

 

 

 

Only the speaker on

Incorrect cable connections.

Connect the cables properly. If the problem persists,

12

one side can be

 

the cables may be defective.

 

heard.

 

 

 

Incorrect balance settings in SET MENU.

Adjust the SPEAKER LEVEL settings.

55

 

 

 

 

 

Only the center

When playing a monaural source with a

 

 

speaker outputs

CINEMA DSP program, the source signal

 

 

substantial sound.

is directed to the center channel, and the

 

 

 

front and surround speakers output effect

 

 

 

sounds.

 

 

 

 

 

 

No sound from the

The sound field programs are turned off.

Press STRAIGHT (EFFECT) to turn them on.

36

effect speakers.

 

 

 

You are using a source or program

Try another sound field program.

44

 

 

combination that does not output sound

 

 

 

from all channels.

 

 

 

 

 

 

No sound from the

The output level of the center speaker is

Raise the level of the center speaker.

55

center speaker.

set to minimum.

 

 

 

 

 

 

 

“CENTER SP” in SET MENU is set to

Select the appropriate setting for the center speaker.

53

 

NONE.

 

 

 

 

 

 

 

One of the Hi-Fi DSP programs (except

Try another sound field program.

44

 

for 7ch Stereo) has been selected.

 

 

 

 

 

 

No sound from the

The output level of the surround speakers

Raise the output level of the surround speakers.

55

surround speakers.

is set to minimum.

 

 

 

 

 

 

 

“SURR L/R SP” in SET MENU is set to

Select the appropriate setting for the surround left and

53

 

NONE.

right speakers.

 

 

 

 

 

 

A monaural source is being played with

Press STRAIGHT (EFFECT) to turn on the sound

—

 

STRAIGHT.

fields.

 

 

 

 

 

No sound from the

Presence speakers are selected.

Select surround back speakers in PR/SB SELECT.

57

surround back

 

 

 

“SURR L/R SP” in SET MENU is set to

If the surround left and right speakers are set to

53

speakers.

 

NONE.

NONE, the surround back speaker setting is

 

 

 

automatically set to NONE. Select the appropriate

 

 

 

setting for the surround speakers.

 

 

 

 

 

 

“SURR B L/R SP” in SET MENU is set to

Select LRGx1 or SMLx1.

54

 

NONE.

 

 

 

 

 

 

No sound from the

“LFE/BASS OUT” in SET MENU is set

Select SWFR or BOTH.

54

subwoofer.

to FRNT when a Dolby Digital or DTS

 

 

 

signal is being played.

 

 

 

 

 

 

 

“LFE/BASS OUT” in SET MENU is set

Select BOTH.

54

 

to SWFR or FRNT when a 2-channel

 

 

 

source is being played.

 

 

 

 

 

 

 

The source does not contain low bass

 

 

 

signals.

 

 

 

 

 

 

 

INFORMATION

ADDITIONAL

 

 

 

 

 

 

 

English

 

 

 

 

71

Page 74 Page 76
Image 75
Page 74 Page 76
Contents HTR-5760 Important Safety Instructions FCC Information for US customers Serial No For Canadian CustomersContents Other features FeaturesBuilt-in 7-channel power amplifier Sound field featuresPlease check that you received all of the following parts Supplied accessoriesInstalling batteries in the remote control Getting StartedFront panel Controls and FunctionsStraight Effect PRESET/TUNING EditInput Mode Speakers A/BRemote control On Screen Using the remote controlHandling the remote control SET Menu A/B/C/D/EFront panel display Presence and surround back speaker indicators 96/24 indicatorLFE indicator Input channel indicatorsAC Outlets Rear panelSpeaker placement Speaker SetupConnecting to Presence speaker terminals Speaker connectionsBanana plug connections Right Left Front speakers a Surround back Speakers Subwoofer System Presence speakersRight Left FrontSubwoofer jack Front terminalsCenter terminals Surround terminalsDigital jacks ConnectionsCable indications Analog jacksConnecting video components Connections for DVD playbackA. model Video Monitor Connecting to the Multi CH Input jacks For 6-channel input A. modelFor 8-channel input A. model Connections for other video components Video AUX jacks on the front panelUse these jacks to connect any video source, such as a MD recorder or Tape deck Connecting audio componentsConnections for audio components A. model CD playerConnecting to an external amplifier Connecting the antennas Connecting the AM loop antenna75-ohm/300-ohm antenna adapter U.K. model only Connecting the power supply cord Connecting the AC power cordMemory back-up Impedance Selector switch Impedance Selector switchTurning on the power Turn on the video monitor connected to this unitFront panel Optimizer microphone position Auto SetupOptimizer microphone setup IntroductionStarting the setup ResultwiringAutomenu Resultexit ErrorError E-5 If an error screen appearsPress u / d to select Result LIST, then press Select When you are finished, press SelectResultwiring screen appears If a warning screen appearsTroubleshooting for auto setup procedure Before auto setupErrors during auto setup Select the input source Adjust the volume to the desired output levelPlayback Basic operationsTo mute the sound To listen with headphones Silent CinemaTo adjust the tone Select a sound field program if desiredFront panel operation Selecting sound field programsMulti CH Input Selecting Multi CH InputDecoders select with j Remote control operationEnjoying multi-channel software Auto AutoPRO Logic SUR. Enhanced Press q/DTS on the remote control to select the decoderEnjoying 2-channel software PRO Logic SUR. StandardThis adjusts the level of compression Listening to high fidelity stereo sound Direct StereoNight listening modes Downmixing to 2 channels Listening to unprocessed input signalsSelecting input modes StraightPress u / d to display the following Information about the input signalDisplaying information about the input SourceTuning Automatic and manual tuningAutomatic tuning Press FM/AM to select the FM band Presetting stationsManual tuning Automatically presetting FM stationsManually presetting stations Automatic preset tuning optionsRepeat steps 1 to 5 to store other stations Selecting preset stationsWhen performing this operation with the remote Control, first press Tuner to set the remote toSee Selecting preset stations Exchanging preset stationsRecording Special considerations when recording DTS softwareFor movie/video sources Sound Field Program DescriptionsSUR. Standard Dolby DigitalSUR. Standard Dolby Digital SUR. EnhancedSUR. Standard PRO Logic PRO LogicRock Concert For music sourcesConcert Hall Jazz ClubP08 Movie Theater Selecting the OSD mode Using the sleep timerSetting the sleep timer Advanced OperationsSleep OFF Canceling the sleep timerPress j / i to adjust the speaker output level Press Select when you have completed your adjustmentUsing the test tone Outputting the test tone from the Presence speakersPress AMP Press Test Option Menu SET MenuSound Menu Input MenuTo exit, press SET Menu when finished Using SET MenuPress u / d to select Manual Setup Press Select to enter Manual SetupSurr L/R SP Sound Menu 1/2Center SP Front SPCross Over Surr B L/R SPPresence SP LFE/BASS OUT02ASUBWOOFER Phase CSP DistanceSpeaker distance CSP Distance Gaudio SET Dcenter GEQElfe Level Fdynamic RangeOptical OUT HPR/SB SelectInput Menu CMPNT-V InputAdisplay SET Binput ModeCoaxial Option MENU1/2Parameter initialization CPARAM. INI Bmemory GuardCPARAM. INI Dzone SETControlling other components Remote Control FeaturesControl area Controlling this unitInput area Category Manufacturer Setting manufacturer codesPress Code SET using a ballpoint pen or similar object Transmit indicator on the remote control flashes twiceMD/CD Controlling other componentsClearing a setup manufacturer code for component control Clearing setup manufacturer codesWhat is a sound field Changing parameter settings Editing Sound Field ParametersElements of a sound field Resetting parameters to the factory presets INIT. DLY Initial delay Sound Field Parameter DescriptionsRoom SIZE/P. Room Size Room size Liveness Surround liveness INIT. DLY Surround initial delaySB INIT. DLY Surround back initial delay Room Size Surround room sizeREV.DELAY Reverberation delay REV.TIME Reverberation timeREV. Level Reverberation level For DTS Neo6 Music Image Center image DIALG.LIFT Dialog liftFor 7ch Stereo CT Width Center widthGeneral TroubleshootingOne side can be Sound suddenlyGoes off Only the speaker onSources cannot be Or DTS indicator onVolume level Dolby Digital or DTSTuner Remote control Does not work norFunction properly Press Straight Effect to select the desired setting Resetting the Factory PresetsBe sure this unit is in standby mode Factory Preset appears in the front panel displayAudio formats GlossaryPCM Linear PCM Sound field programsAudio information LFE 0.1 channelVideo signal Video signal informationComponent video signal Composite video signalSpecifications List of Manufacturer Codes VCR Cable TVSatellite Tuner DBSCD Player DVD PlayerDVD Recorder LD PlayerCD Recorder MD RecorderTape Deck WC85600

HTR-5760 specifications

The Yamaha HTR-5760 is a comprehensive home theater receiver that delivers exceptional audio and video performance, making it an excellent choice for both casual listeners and serious audiophiles. This model combines advanced technology with user-friendly features, ensuring a versatile and immersive home entertainment experience.

One of the standout features of the HTR-5760 is its robust power output, which typically offers up to 100 watts per channel across seven channels. This capability allows the receiver to drive various speaker configurations, ensuring that users can enjoy powerful, clear sound whether they are watching movies or listening to music. The receiver is also equipped with Dolby Digital and DTS decoding, providing support for high-definition sound formats that enhance the overall audio experience.

The HTR-5760 employs Yamaha’s proprietary YPAO (Yamaha Parametric room Acoustic Optimizer) technology. This innovative feature automatically analyzes the room's acoustics and adjusts the receiver's settings to achieve optimal sound performance, tailoring the audio output for the best possible experience in any environment.

In terms of video capabilities, the HTR-5760 features onboard support for component video upconversion, allowing users to connect various source devices without the need for multiple cables. This feature provides convenience and reduces clutter when setting up a home theater system. The receiver is also HDMI-compliant, enabling users to connect the latest high-definition devices and enjoy enhanced picture quality across all compatible devices.

Another noteworthy characteristic is the HTR-5760’s multiple inputs and outputs, which include various analog and digital audio connections, video inputs, and even zone capabilities for multi-room audio distribution. It also includes numerous preset sound modes to enhance different types of media, from sports to music and movies.

Furthermore, the Yamaha HTR-5760 boasts a sleek and elegant design that fits seamlessly into any home setup. Its intuitive remote control makes it easy to navigate through the various settings and options available.

In summary, the Yamaha HTR-5760 is a feature-rich receiver that excels in delivering high-quality audio and video, backed by advanced technologies. Whether you are a movie enthusiast or a music lover, this home theater receiver stands out as a solid choice for creating a captivating audio-visual experience at home. Its blend of power, innovation, and user-friendly design ensures it remains relevant in the evolving landscape of home entertainment.
Top Page Image Contents